->prereset() returns -ENOENT to tell libata that the port is empty and
reset sequencing should be stopped.  This is not an error condition.
Update ata_eh_reset() such that it sets device classes to ATA_DEV_NONE
and return success in on -ENOENT.  This makes spurious error message
go away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Since d9a9cdfb <linux/sysfs.h> is using
ENOSYS without including <linux/errno.h> if CONFIG_SYSFS is disabled.

Fixed by including <linux/errno.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These leaks were reported by: Catalin Marinas <catalin.marians@gmail.com>
and I have been able to very by inspection they are possible.

When converting tty_io.c to store pids as struct pid pointers instead
of pid_t values it appears I overlooked two places where we stop using
the pid value.  The very obvious one is in do_tty_hangup, and the one
the less obvious one in __proc_set_tty.

When looking into the code __proc_set_tty only has pids that need to
be put because of failures of other parts of the code to properly
perform hangup processing.   Fixing the leak here in __proc_set_tty
is easy and obviously correct so I am doing that first.

Fixing the places that should be performing hangup processing is much
less obviously correct.  So those I'm aiming those patches at -mm.
for now, so the can age a while before they are merged.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Build fix:  sa1100/generic.c should already have included <asm/gpio.h>,
but it didn't ... causing a build problem with a recent patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When PM-Timer is available for local APIC timer calibration we can skip the
verification of the calibrated time value.  The resulting error is quite
small on a bunch of evaluated platforms and is less harming than the
observed false positives.

We need to keep the verification on systems, which have no PM-Timer to
avoid bogus local APIC timer calibrations in the range of factor 2-10,
which can be observed when swicthing off the PM-timer support in the kernel
configuration.

The wrong calibration values are probably caused by SMM code trying to
emulate a PS/2 keyboard from a (maybe connected or not) USB keyboard.  This
prohibits the accurate delivery of PIT interrupts, which are used to
calibrate the local APIC timer.  Unfortunately we have no way to disable
this BIOS misfeature in the early boot process.

Add also the dropped cpu_relax() back to the wait loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix atomicity of TIF update in flush_thread() for x86_64

Race :

parent process executing :
sys_ptrace()
 (lock_kernel())
 (ptrace_get_task_struct(pid))
 arch_ptrace()
   ptrace_detach()
     ptrace_disable(child);
       clear_singlestep(child);
         clear_tsk_thread_flag(child, TIF_SINGLESTEP);
         (which clears the TIF_SINGLESTEP flag atomically from a different
	  process)
 (put_task_struct(child))
 (unlock_kernel())

And at the same time, in the child process :
sys_execve()
 do_execve()
   search_binary_handler()
     load_elf_binary()
       flush_old_exec()
         flush_thread()
           doing a non-atomic thread flag update
Signed-off-by: Rebecca Schultz <rschultz@google.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/char/watchdog/machzwd.c: In function 'zf_ioctl':
drivers/char/watchdog/machzwd.c:327: warning: passing argument 1 of 'zf_ping' makes integer from pointer without a cast

Also some coding-style repairs.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a missing #define for the platform_kernel_launch_event.  Without this
fix, a call to platform_kernel_launch_event() becomes a noop on generic
kernels.  SN systems require this fix to successfully kdump/kexec from
certain hardware errors.

[bwalle@suse.de: fix it]
Signed-off-by: John Keller <jpk@sgi.com>
Cc: Bernhard Walle <bwalle@suse.de>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Jay Lan <jlan@sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In sn_io_slot_fixup(), the parent is re-set from the bus to
io(port|mem)_resource because the address is changed in a way that it's not
child of the bus any more.

However, only the root is set but not the parent/child/sibling relationship
in the resource tree which causes 'cat /proc/iomem' to stop after this
memory area.  Depding on the poition in the tree the iomem may be nearly
completely empty.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: John Keller <jpk@sgi.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_TABLE=m
CONFIG_X86_P4_CLOCKMOD=y

arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_verify':p4-clockmod.c:(.text.cpufreq_p4_verify+0x8): undefined reference to `cpufreq_frequency_table_verify'
arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_cpu_exit':p4-clockmod.c:(.text.cpufreq_p4_cpu_exit+0x8): undefined reference to `cpufreq_frequency_table_put_attr'
arch/x86_64/kernel/built-in.o: In function `cpufreq_p4_cpu_init':p4-clockmod.c:(.text.cpufreq_p4_cpu_init+0x13b): undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'linus' of git://kvm.qumranet.com/home/avi/kvm:
  KVM: MMU: Fix host memory corruption on i386 with >= 4GB ram
  KVM: MMU: Fix guest writes to nonpae pde
  KVM: Fix guest sysenter on vmx
  KVM: Unset kvm_arch_ops if arch module loading failed

* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
  [ALSA] hda-intel - Fix HDA buffer alignment
  [ALSA] hda-codec - Add model for HP Compaq d5750
  [ALSA] hda-codec - Add support for MacBook Pro 1st generation
  [ALSA] version 1.0.14rc3
  [ALSA] hda-codec - Add model for HP Compaq d5700
  [ALSA] intel8x0 - Fix Oops at kdump crash kernel
  [ALSA] hda-codec - Fix speaker output on MacPro
  [ALSA] hda-codec - more systems for Analog Devices
  [ALSA] hda-intel - Fix codec probe with ATI contorllers
  [ALSA] hda-codec - Add suppoprt for Asus M2N-SLI motherboard
  [ALSA] intel8x0 - Fix speaker output after S2RAM
  [ALSA] ac97 - fix AD shared shared jack control logic
  [ALSA] soc - Fix dependencies in Kconfig files

PAGE_MASK is an unsigned long, so using it to mask physical addresses on
i386 (which are 64-bit wide) leads to truncation.  This can result in
page->private of unrelated memory pages being modified, with disasterous
results.

Fix by not using PAGE_MASK for physical addresses; instead calculate
the correct value directly from PAGE_SIZE.  Also fix a similar BUG_ON().
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>

KVM shadow page tables are always in pae mode, regardless of the guest
setting.  This means that a guest pde (mapping 4MB of memory) is mapped
to two shadow pdes (mapping 2MB each).

When the guest writes to a pte or pde, we intercept the write and emulate it.
We also remove any shadowed mappings corresponding to the write.  Since the
mmu did not account for the doubling in the number of pdes, it removed the
wrong entry, resulting in a mismatch between shadow page tables and guest
page tables, followed shortly by guest memory corruption.

This patch fixes the problem by detecting the special case of writing to
a non-pae pde and adjusting the address and number of shadow pdes zapped
accordingly.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>

The vmx code currently treats the guest's sysenter support msrs as 32-bit
values, which breaks 32-bit compat mode userspace on 64-bit guests.  Fix by
using the native word width of the machine.
Signed-off-by: Avi Kivity <avi@qumranet.com>

Otherwise, the core module thinks the arch module is loaded, and won't
let you reload it after you've fixed the bug.
Signed-off-by: Avi Kivity <avi@qumranet.com>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Use Kconfig.preempt

* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide: remove CONFIG_IDEDMA_{ICS,PCI}_AUTO config options
  ide: don't allow DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n
  scc_pata: dependency fix
  jmicron: make ide jmicron driver play nice with libata ones
  ide: remove static prototypes from include/asm-mips/mach-au1x00/au1xxx_ide.h
  ide: au1xxx: fix use of mixed declarations and code
  cmd64x: fix recovery time calculation (take 3)

* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
  [PATCH] x86: Export _proxy_pda for gcc 4.2
  [PATCH] i386: Don't use the TSC in sched_clock if unstable
  [PATCH] x86-64: fix section mismatch warnings
  [PATCH] i386: Enforce GPLness of VMI ROM
  [PATCH] x86-64: wire up compat sched_rr_get_interval(2)
  [PATCH] i386: Update defconfig
  [PATCH] x86-64: Update defconfig

Signed-off-by: David S. Miller <davem@davemloft.net>

All modern distributions have been setting these options to "y" for ages.
(additionally "n" cases have been obsoleted for few years).  Therefore use
DMA by default and remove CONFIG_IDEDMA_{ICS,PCI}_AUTO (also remove no longer
needed CONFIG_IDEDMA_AUTO).  This fixes DMA support for rare configurations
where CONFIG_IDEDMA_{ICS,PCI}_AUTO was set to "n" but "hdparm -d 1" was used
to enable DMA support and which were forced to PIO mode by "ide: don't allow
DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n" patch.  There is no
functionality loss because "ide=nodma" kernel option is still available.

Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

For CONFIG_IDEDMA_{ICS,PCI}_AUTO=n and/or "ide=nodma" option the host/device
are not programmed for DMA and it is also explicitly disabled by ide_set_dma()
(->ide_dma_check returns "-1").  However the code responsible for manually
enabling DMA ("hdparm -d 1") has a bug which results in DMA being erroneously
enabled - ide_set_dma() incorrectly passes "0" return value to set_using_dma().
This may work if BIOS/firmware configured the host/device for DMA and chipset
allows independent configuration of DMA/PIO modes but won't work after suspend
and is generally unsafe on many chipsets (possibly including data corruption
if the same registers are used for DMA/PIO timings).

This patch fixes kernel bugzilla bug #8169 (piix host driver fixes for
setting PIO mode exposed the problem described above).  The side-effect of
the fix is that some rare configuration may be forced to PIO mode when DMA
mode was previously used - this is addressed by the next patch which removes
CONFIG_IDEDMA_{PCI,ICS}_AUTO config option completely.

Thanks goes out to Patrick Horn for reporting the issue, narrowing it down
to the specific commit and testing the fix.  Also thanks to Sergei Shtylyov
for help in debugging the problem.

Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch fixes:
* the dependency of scc_pata on BLK_DEV_IDEDMA_PCI
* incorrect link to ide-core
* move scc_pata from ide/ppc to ide/pci
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Al Viro <viro@ftp.linux.org.uk>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

When libata is configured, the device is configured such that SATA and
PATA ports live in separate functions with different programming
interfaces.  pata_jmicron and ide jmicron drivers can drive only the
PATA part.

This patch makes jmicron match PCI class code such that it doesn't
attach itself to the SATA part preventing the proper ahci driver from
attaching.

This change is suggested by Bartlomiej.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: justin@jmicron.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch removes the static prototypes from the au1xxx_ide.h, some of
them were not even implemented. Also, they caused build breakage since
they differed from the functions actually implemented in
drivers/ide/mips/au1xxx-ide.c.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/mips/au1xxx-ide.c:684: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver wrongly takes the address setup time into account when calculating
the PIO recovery time -- this leads to slight overclocking of the PIO modes 0
and 1 (so, the prayers failed to help, as usual :-).  Rework the code to be
calculating recovery clock count as a difference between the total cycle count
and the active count (we don't need to calculate the recovery time itself since
it's not specified for the PIO modes 0 to 2, and for modes 3 and 4 this formula
gives enough recovery time anyway in the chip's supported PCI frequency range).

This patch has been inspired by reading the datasheets and looking at what the
libata driver does; it has been compile-tested only (as usual :-) but anyway,
the new code gives the same or longer recovery times than the old one...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

I finally found a dual core box, which survives suspend/resume without
crashing in the middle of nowhere. Sigh, I never figured out from the
code and the bug reports what's going on.

The observed hangs are caused by a stale state transition of the clock
event devices, which keeps the RCU synchronization away from completion,
when the non boot CPU is brought back up.

The suspend/resume in oneshot mode needs the similar care as the
periodic mode during suspend to RAM. My assumption that the state
transitions during the different shutdown/bringups of s2disk would go
through the periodic boot phase and then switch over to highres resp.
nohz mode were simply wrong.

Add the appropriate suspend / resume handling for the non periodic
modes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6]: ipv6_fl_socklist is inadvertently shared.
  [TCP]: Fix tcp_mem[] initialization.
  [NET]: Copy mac_len in skb_clone() as well
  [IPV4]: Do not disable preemption in trie_leaf_remove().

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Get DEBUG_PAGEALLOC working again.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Kconfig: Move missplaced NR_CPUS default from SMTC to VSMP.
  [MIPS] Lockdep: Fix recursion bug.
  [MIPS] RTLX: Handle copy_*_user return values.
  [MIPS] RTLX: Protect rtlx_{read,write} with mutex.
  [MIPS] RTLX: Harden against compiler reordering and optimization.
  [MIPS] RTLX: Don't use volatile; it's fragile.
  [MIPS] Lasat: Downgrade 64-bit kernel from experimental to broken.
  [MIPS] Compat: Fix build if CONFIG_SYSVIPC is disabled.
  [CHAR] lcd: Fix two warnings.
  [MIPS] FPU ownership management & preemption fixes
  [MIPS] Check FCSR for pending interrupts, alternative version
  [MIPS] IP27, IP35: Fix warnings.

The maximum seconds value we can handle on 32bit is LONG_MAX.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix typo in sync_constant_test_bit()'s name, so sync_bitops.h is consistent
with bitops.h
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The set_cs field of struct s3c24xx_spi is declared as returning a int but
the value returned but set_cs is never fixed.  Moreover, the default
function for set_cs and the set_cs defintion in the platform data are
returning void.

I'm proposing to change the prototype to void (*set_cs)(...). By doing
this, I'm also fixing 2 build warnings:

  drivers/spi/spi_s3c24xx.c: In function 's3c24xx_spi_probe':
  drivers/spi/spi_s3c24xx.c:330: warning: assignment from incompatible pointer type
  drivers/spi/spi_s3c24xx.c:335: warning: assignment from incompatible pointer type
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This bug was seen on ppc64, but it could have occurred on any
architecture with a page size of 64k or above.  The problem is that in
fs/binfmt_elf.c:randomize_stack_top() randomizes the stack to within
0x7ff pages.  On 4k page machines, this is 8MB; on 64k page boxes, this
is 128MB.

The problem is that the new binary layout (selected in
arch_pick_mmap_layout) places the mapping segment 128MB or the stack
rlimit away from the top of the process memory, whichever is larger.  If
you chose an rlimit of less than 128MB (most defaults are in the 8Mb
range) then you can end up having your entire stack randomized away.

The fix is to make randomize_stack_top() only steal at most 8MB, which this
patch does.  However, I have to point out that even with this, your stack
rlimit might not be exactly what you get if it's > 128MB, because you're
still losing the random offset of up to 8MB.

The true fix should be to leave an explicit gap for the randomization plus
a buffer when determining mmap_base, but that would involve fixing all the
architectures.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes a bogus lockdep warning which causes lockdep to disable itself.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Looking at oom_kill.c, found that the intention to not kill the selected
process if any of its children/siblings has OOM_DISABLE set, is not being
met.
Signed-off-by: Ankita Garg <ankita@in.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove the misleading "Presently only useful on the IA-64 platform" text
from the EFI partition Kconfig.

EFI partitions are also used by Apple on their Intel-based machines and
thus you need EFI partition support if you (for example) want to attach
such a machine in target disk mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Testing of -rt by IBM uncovered a locking bug in wake_futex_pi(): the PI
state needs to be locked before we access it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Marcel Selhorst <tpm@selhorst.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>