Ethernet hangs off OTG
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Get serial port working for now
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The i.MX51 ECSPI has a fifo size of 64 entries instead of 8 entries as
found on the other cspi bus devices.

Cc: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.

This fix should not hurt already working CPUs, as they are using the written
register value already.

Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.

While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This fixes

	arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
	arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used

when USB_ULPI is not selected.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on work done earlier by Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Also, remove the deprecated symbols from arch/arm/mach-mx3/cpu.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>

This patch add a LED class driver for LEDs found on the LaCie 2Big and
5Big Network v2 boards. The LEDs are wired to a CPLD and are controlled
through a GPIO extension bus.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>

dev_set_drvdata() can't be used to set the driver private data pointer.
This would overwrite the led classdev object previously registered by
led_classdev_register().

Note that despite this mistake, the driver work fine because led_dat and
led_dat->cdev are at the same memory address.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>

Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: David Miller <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>

The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.

This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.

Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
 bit 0:
     0 => 1 sd/mmc slot
     1 => 2 sd/mmc slots connectors (board from revision C)

system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore.
Change wrong configuration variables that were remaining.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.

The other boards revision will be specified via system_rev.

for 9g45ekes, m10g45ekes and m10g45ek boards and revisions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Octeon: Place cnmips_cu2_setup in __init memory.
  MIPS: Don't place cu2 notifiers in __cpuinitdata
  MIPS: Calculate VMLINUZ_LOAD_ADDRESS based on the length of vmlinux.bin
  MIPS: Alchemy: Resolve prom section mismatches
  MIPS: Fix syscall 64 bit number comments.
  MIPS: Hookup fanotify_init, fanotify_mark, and prlimit64 syscalls.
  MIPS: TX49xx: Rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
  MIPS: N32: Fix getdents64 syscall for n32
  MIPS: Remove pr_<level> uses of KERN_<level>
  MIPS: PNX8550: Sort out machine halt, restart and powerdown functions.
  MIPS: GIC: Remove dependencies from Malta files.
  MIPS: Kconfig: Fix and clarify kconfig help text for VSMP and SMTC.
  MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.
  MIPS: Audit: Fix hang in entry.S.
  MIPS: Document why RELOC_HIDE is there.
  MIPS: Octeon: Determine if helper needs to be built
  MIPS: Use generic atomic64 for 32-bit kernels
  MIPS: RM7000: Symbol should be static
  MIPS: kspd: Adjust confusing if indentation
  MIPS: Fix a typo.

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  writeback: always use sb->s_bdi for writeback purposes

* 'v2.6.36-rc6-urgent-fixes' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
  xen: do not initialize PV timers on HVM if !xen_have_vector_callback
  xen: do not set xenstored_ready before xenbus_probe on hvm

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: Initialize total_len in fuse_retrieve()

Masking in the ack callback fails to work with handle_percpu_irq and handle_edge_irq.
The interrupt stays disabled after the first invocation since percpu and edge irq do
not unmask an interrupt after handling it. For handle_level_irq masking in the ack
is redundant because ack is always called after mask in the mask_ack function.

Masking in the ack function is required only when __do_IRQ was used instead of flow
handlers, but using __do_IRQ has been deprecated.

Remove the masking of interrupt from the ack callback.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>

Since powerpc uses -Werror on arch powerpc, the build was broken like
this:

  cc1: warnings being treated as errors
  arch/powerpc/kernel/module.c: In function 'module_finalize':
  arch/powerpc/kernel/module.c:66: error: unused variable 'err'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: rcu_read_lock_bh_held(): disabling irqs also disables bh
  generic-ipi: Fix deadlock in __smp_call_function_single

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf trace scripting: Fix extern struct definitions
  perf ui hist browser: Fix segfault on 'a' for annotate
  perf tools: Fix build breakage
  perf, x86: Handle in flight NMIs on P4 platform
  oprofile, ARM: Release resources on failure
  oprofile: Add Support for Intel CPU Family 6 / Model 29

The "flags" member of "struct wait_queue_t" is used in several places in
the kernel code without beeing initialized by init_wait().  "flags" is
used in bitwise operations.

If "flags" not initialized then unexpected behaviour may take place.
Incorrect flags might used later in code.

Added initialization of "wait_queue_t.flags" with zero value into
"init_wait".
Signed-off-by: Evgeny Kuznetsov <EXT-Eugeny.Kuznetsov@nokia.com>
[ The bit we care about does end up being initialized by both
   prepare_to_wait() and add_to_wait_queue(), so this doesn't seem to
   cause actual bugs, but is definitely the right thing to do -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>