potential uninitialized variable num_xfrms

fix compiler warning: 'num_xfrms' may be used uninitialized in this function.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
 net/xfrm/xfrm_policy.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_recv_ts_and_drops() is fat and slow (~ 4% of cpu time on some
profiles)

We can test all socket flags at once to make fast path fast again.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes vid/pid for Ericsson MBM devices from the whitelist set of
devices. The MBM devices are instead identified by GUID.

In order for cdc_ether to handle these devices the GUID in the MDLM descriptor
is tested. All MBM devices currently handled by cdc_ether as well as future
CDC Ethernet MBM devices can be identified by the GUID.

This is the same solution used in Carl Nordbeck's mbm driver,
http://kerneltrap.org/mailarchive/linux-usb/2008/11/17/4141384/thread

I post this as RFC to get feedback on however cdc_ether is the correct place to
do the binding, or if it should be done in a separate driver, e.g. zaurus.
Signed-off-by: Jonas Sjöquist <jonas.sjoquist@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following does the same thing without the extra overhead
of testing all the registers. It also handles the out of memory
case.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When queueing a skb to socket, we can immediately release its dst if
target socket do not use IP_CMSG_PKTINFO.

tcp_data_queue() can drop dst too.

This to benefit from a hot cache line and avoid the receiver, possibly
on another cpu, to dirty this cache line himself.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 95766fff ([UDP]: Add memory accounting.), 
each received packet needs one extra sock_lock()/sock_release() pair.

This added latency because of possible backlog handling. Then later,
ticket spinlocks added yet another latency source in case of DDOS.

This patch introduces lock_sock_bh() and unlock_sock_bh()
synchronization primitives, avoiding one atomic operation and backlog
processing.

skb_free_datagram_locked() uses them instead of full blown
lock_sock()/release_sock(). skb is orphaned inside locked section for
proper socket memory reclaim, and finally freed outside of it.

UDP receive path now take the socket spinlock only once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in your merge in 5c01d566 you added "int
i;" into wl1271_main.c which is unused in that function.

This patch fixes the merge problem:
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
o Bugfix: Flow control was causing the device to be destroyed.
o Bugfix: Handle CAIF channel connect failures.
o If the underlying link layer is gone the net-device is no longer removed,
  but closed.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
 This is a complete re-write of the socket layer. Making the socket
 implementation more aligned with the other socket layers and using more
 of the support functions available in sock.c. Lots of code is copied
 from af_unix (and some from af_irda).
 Non-blocking mode should be working as well.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
o Function cfcnfg_disconn_adapt_layer is changed to do asynchronous
  disconnect, not waiting for any response from the modem. Due to this
  the function cfcnfg_linkdestroy_rsp does nothing anymore.
o Because disconnect may take down a connection before a connect response
  is received the function cfcnfg_linkup_rsp is checking if the client is
  still waiting for the response, if not a disconnect request is sent to
  the modem.
o cfctrl is no longer keeping track of pending disconnect requests.
o Added function cfctrl_cancel_req, which is used for deleting a pending
  connect request if disconnect is done before connect response is received.
o Removed unused function cfctrl_insert_req2
o Added better handling of connect reject from modem.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
o Added functions cfsrvl_get and cfsrvl_put.
o Added support release_client to use by socket and net device.
o Increase reference counting for in-flight packets from cfmuxl
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
 o Renamed cfcnfg_del_adapt_layer to cfcnfg_disconn_adapt_layer
 o Fixed typo cfcfg to cfcnfg
 o Renamed linkid to channel_id
 o Updated documentation in caif_dev.h
 o Minor formatting changes
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
   o Added permission checks for installing. CAP_SYS_ADMIN and
     CAP_SYS_TTY_CONFIG can install the ldisc.
   o Check if allocation of skb was successful.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a core TX queue and 2 hardware TX queues for each channel.
If separate_tx_channels is set, create equal numbers of RX and TX
channels instead.

Rewrite the channel and queue iteration macros accordingly.
Eliminate efx_channel::used_flags as redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes no immediate difference, but we definitely do not want
to test all TX queues once we allocate a pair of TX queues to each
channel.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for this to be unsigned long; make it unsigned int.
It does need a line in kernel-doc, so add that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently TX completions do not count towards the NAPI budget.  This
means a continuous stream of TX completions can cause the polling
function to loop indefinitely with scheduling disabled.  To avoid
this, follow the common practice of reporting the budget spent after
processing one ring-full of TX completions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When set, an event is not sent whenever periodic MAC statistics are
raised.  This avoids unnecessary wake-ups.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parity errors in different blocks of SRAM may set one of two different
interrupt flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Siena has two problems with legacy interrupts:
  1. There is no synchronisation between the ISR read completion,
     and the interrupt deassert message.
  2. A downstream read at the "wrong" moment can return 0, and
     suppress generating the next interrupt.

Falcon should suffer from both of these, and it appears it does.
Enable EFX_WORKAROUND_15783 on Falcon as well.

Also, when we see queues == 0, ensure we always schedule or rearm
every event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a regression introduced in d3245b28
"sfc: Refactor link configuration".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The aim of this code was to avoid a spurious XGMII fault over a MAC
reconfigure. It's less relevant now that the PHY reconfigure isn't
called from the MAC reconfigure.

After applying this patch, our link stress test passed 48 hours of
testing without ever resetting the PHY.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'Fatal' errors set an interrupt flag associated with a specific event
queue; only read the syndrome vector if we see that queue's flag set
(legacy interrupts) or in the interrupt handler for that queue (MSI).

Do not ignore an interrupt if the fatal error flag is set but specific
error flags are all zero.  Even if we don't schedule a reset, we must
respect the queue mask and rearm the appropriate event queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some cases failing functions were returning 0 which is obviously wrong.
In other cases they were returning inappropriate error codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Siena has a separate SRAM bank for each port.  On single-port boards
these can be merged together, so each port has an interrupt flag for
parity errors in the other port's SRAM.  Currently we do not enable
such merging and should mask this interrupt source.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This replace the PCI DMA state API (include/linux/pci-dma.h) with the
DMA equivalents since the PCI DMA state API will be obsolete.

No functional change.

For further information about the background:

http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Even on 64bit arches, sizeof(struct sk_buff) < 256
2) No need to prefetch same pointer twice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Eliezer Tamir <eliezer@tamir.org.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to an errata in 82598 parts MSI-X needs to be disabled
in certain ixgbe devices designed to transfer peer-to-peer
traffic on the PCIe bus. This patch sets the default
interrupt type to MSI rather than MSI-X for specific Cisco
ixgbe adapters.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move some declarations around to make it clearer which variables
are being used inside loop.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recently introduced bridge mulitcast port group list was only
partially using RCU correctly. It was missing rcu_dereference()
and missing the necessary barrier on deletion.

The code should have used one of the standard list methods (list or hlist)
instead of open coding a RCU based link list.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix unsafe usage of RCU. Would never work on Alpha SMP because
of lack of rcu_dereference()
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

By coding slightly differently, there are only two cases
to deal with: add at head and add after previous entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds registers (,tx/rx rings' status and so on) printout
code just before resetting adapters. This will be helpful for detecting
the root cause of adapters reset.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>