- 06 Apr, 2022 7 commits
-
-
Lucas De Marchi authored
Since gen6 we use FPGA_DBG register to detect unclaimed MMIO registers. This register is in the display engine IP and can only ever detect unclaimed accesses to registers in this area. However sometimes there are reports of this triggering for registers in other areas, which should not be possible. Right now we always warn after the read/write of registers going through unclaimed_reg_debug(). However places using __raw_uncore_* may be triggering the unclaimed access and those being later accounted to a different register. Let's warn both before and after the read/write with a slightly different message, so it's clear if the register reported in the warning is actually the culprit. Commit dda96033 ("drm/i915: Just clear the mmiodebug before a register access") attempted to solve the same issue by removing the warning when if FPGA_DBG flags before the mmio read/write. However, it doesn't solve it completely as FPGA_DBG may remain set when reading registers outside display. So in the end the check after the mmio read/write triggers the warning pointing to the wrong register. Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220405001149.2675226-1-lucas.demarchi@intel.com
-
Imre Deak authored
Accessing the DDI_BUF_CTL register without the port's DDI clock being enabled (to set/clear the TypeC PHY ownership for the port) can lead to a corrupted value read during any i915 register access right after the DDI clock is enabled. The root cause is the way clock synchronization works for this register, controlled by the CHICKEN_DCPR_1 DDI_CLOCK_REG_ACCESS flag. Correctly this flag should be cleared on ADLP (see the Bspec link below), however after bootup the flag is set. One easily reproducible issue is an unclaimed register access of the PWR_WELL_CTL_DDI2 register, programmed right after DDI clock enabling to enable the port's DDI_IO power well (see the HSDES, VLK links below). With the correct setting above this problem can't be reproduced. Bspec: 49189 HSDES: 18019028154 VLK: 28328, 28655 Cc: Jouni Högander <jouni.hogander@intel.com> Cc: Arthur J Runyan <arthur.j.runyan@intel.com> Signed-off-by:
Imre Deak <imre.deak@intel.com> Acked-by:
Arthur J Runyan <arthur.j.runyan@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220323201749.288566-1-imre.deak@intel.com
-
Casey Bowman authored
Split i915_run_as_guest() into a more arch-friendly function as non-x86 builds do not support this functionality. Signed-off-by:
Casey Bowman <casey.g.bowman@intel.com> Acked-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
-
José Roberto de Souza authored
Instead of exit PSR when a frontbuffer invalidation happens, we can enable the PSR2 selective fetch continuous full frame, that will keep the panel updated like PSR was disabled but without keeping PSR active. So as soon as the frontbuffer flush happens we can disable the continuous full frame and start to do selective fetches much quicker than the path that would enable PSR, that will wait a few frames to actually activate PSR. Also this approach has proven to fix some glitches found in Alderlake-P when there are a lot of invalidations happening together with page flips. Some may ask why it is writing to CURSURFLIVE(), it is because that is the way that hardware team provided us to poke display to handle PSR updates, and it is being used since display 9. v2: - handling possible race conditions between frontbuffer rendering and page flips Reviewed-by:
Jouni Högander <jouni.hogander@intel.com> Cc: Khaled Almahallawy <khaled.almahallawy@intel.com> Cc: Shawn C Lee <shawn.c.lee@intel.com> Cc: Jouni Högander <jouni.hogander@intel.com> Cc: Mika Kahola <mika.kahola@intel.com> Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220405155344.47219-3-jose.souza@intel.com
-
José Roberto de Souza authored
Frontbuffer rendering and page flips can race with each other and this can potentialy cause issues with PSR2 selective fetch. And because pipe/crtc updates are time sentive we can't grab the PSR lock after intel_pipe_update_start() and before intel_pipe_update_end(). So here adding the lock and unlock functions and calls, the proper PSR2 selective fetch handling will come in a separated patch. v2: - fixed new functions documentation Reviewed-by:
-
José Roberto de Souza authored
Following up what was done in commit 804f4688 ("drm/i915/psr: Set "SF Partial Frame Enable" also on full update") and also setting partial frame enable when psr_force_hw_tracking_exit() is called. Also as PSR2_MAN_TRK_CTL is a double buffered registers do a RMW is not a good idea so here also setting the man_trk_ctl_enable_bit() that is required in TGL and only doing a register write. v2: - not doing a rmw v3: - removing the inline from functions that return PSR2_MAN_TRK_CTL bits Reviewed-by:
-
Ashutosh Dixit authored
Because VLV_GT_RENDER_RC6 == GEN6_GT_GFX_RC6, the IS_VALLEYVIEW() check is not needed. Neither is the check present in other code paths which call intel_rc6_residency_ns() (in functions gen6_drpc(), rc6_residency() and rc6_residency_ms_show()). v2: Elimintate VLV_GT_RENDER_RC6 #define (Jani) Cc: Jani Nikula <jani.nikula@linux.intel.com> Signed-off-by:
Ashutosh Dixit <ashutosh.dixit@intel.com> Reviewed-by:
Badal Nilawar <badal.nilawar@intel.com> Signed-off-by:
Anshuman Gupta <anshuman.gupta@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220314161310.6468-1-ashutosh.dixit@intel.com
-
- 05 Apr, 2022 12 commits
-
-
Animesh Manna authored
The request to aqquire gem resources is failing for DSB in rare scenario where it is busy and the register programming will be done through mmio fallback path. DSB has extra advantage of faster register programming which may go away through mmio path. Adding wait for gem resource also may not be right as anyways losing time. To make the CI execution happy replaced drm_err() to drm_info() for printing debug info during dsb buffer preparation. v1: Initial version. v2: Added print for mmio fallback at out label. [Nirmoy] v3: Improved debug message. [Nirmoy] Cc: Nirmoy Das <nirmoy.das@linux.intel.com> Signed-off-by:
Animesh Manna <animesh.manna@intel.com> Signed-off-by:
Uma Shankar <uma.shankar@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220325161140.11906-1-animesh.manna@intel.comReviewed-by:
Nirmoy Das <nirmoy.das@intel.com>
-
Ville Syrjälä authored
Our YCbCr output is always supposed to be limited range BT.709. That's what we send with native HDMI. The conn_state->colorspace stuff is entirely independent of that and is not supposed to alter the generated output in any way. If we want a way to do that then we need a new proprty for it. Make it so that the RGB->YCbCr conversion when performed by the DPF will match the BT.709 we would transmit with native HDMI. Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Signed-off-by:
-
Ville Syrjälä authored
With native HDMI we allow the user to override the mode with something that may not respect the downstream (sink,dual-mode adapter) TMDS clock limits. Let's reuse the same logic for DP HDMI DFPs so that behaviour is more or less uniform. Signed-off-by:
-
Ville Syrjälä authored
Currently we only support "4:2:0 also" modes on native HDMI. Extend that support for DP as well. With all the HDMI DFP TMDS clock handling sorted out this is now going to work for both native DP and DP->HDMI converters. As with native HDMI we first check if RGB output is possible, and if not we try YCbCr 4:2:0 instead. Signed-off-by:
-
Ville Syrjälä authored
Rework the HDMI DFP TMDS clock checks to also check at 8bpc. Previously we only checked the deep color cases. But I suppose a sink could potentially declare "4:2:0 also" modes that only actually fit within its own limits when using 4:2:0. Even if that is too nuts to be real there is no real harm in running through the full checks for everything. Signed-off-by:
-
Ville Syrjälä authored
Hoist the drm_mode_is_420_only() from intel_dp_output_format() into the caller. This will allow intel_dp_output_format() to be reused for "4:2:0 also" modes. Signed-off-by:
-
Ville Syrjälä authored
Prefer to use intel_connector over drm_connector. Also clean up the related variable names a bit. Signed-off-by:
-
Ville Syrjälä authored
Consolidate the double pfit call, and reorder things so that intel_dp_output_format() and intel_dp_compute_link_config() are back-to-back. They are intimately related, and will need to be called twice to properly handle the "4:2:0 also" modes. Signed-off-by:
-
Ville Syrjälä authored
intel_dp_hdmi_ycbcr420() does account for native DP 4:2:0 output as well, so lets rename it a bit. Signed-off-by:
-
Ville Syrjälä authored
Declutter intel_dp_compute_config() a bit by moving the has_audio computation into a helper. HDMI already does the same thing. Signed-off-by:
-
Ville Syrjälä authored
Currently we only look at the DFPs max TMDS clock limit when considering whether the mode is valid, or whether we can do deep color. The sink's max TMDS clock limit may be lower than the DFPs, so we need to account for it as well. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4095 Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2844Signed-off-by:
-
Ville Syrjälä authored
We're currently duplicating the DFP min/max TMDS clock checks in .mode_valid() and .compute_config(). Extract a helper suitable for both use cases. Signed-off-by:
-
- 04 Apr, 2022 3 commits
-
-
Ville Syrjälä authored
All the LFP data table pointers have uniform layout. Turn that into a struct. Signed-off-by:
Jani Nikula <jani.nikula@intel.com>
-
Ville Syrjälä authored
Remove some zombies from our device structure. Signed-off-by:
-
Ville Syrjälä authored
Stop hand rolling drm_connector_attach_hdr_output_metadata_property(). Signed-off-by:
-
- 31 Mar, 2022 11 commits
-
-
Ville Syrjälä authored
Nothing special about static DRRS on LVDS, it's just your bog standard modeset. Let's allow it. Signed-off-by:
-
Ville Syrjälä authored
Only seamless DRRS has specific hardware requirements so we can allow static DRRS on any eDP port. And we can replace these port checks and whatnot with a simple check to make sure the transcoder(s) we're about to use are capable of seamless DRRS. Signed-off-by:
-
Ville Syrjälä authored
intel_drrs_compute_config() is 100% DP specific. DRRS on other types of encoders wouldn't do any of these M2/N2 calculations etc. So let's move this into intel_dp.c so all the DP state calculation is more concentrated into one place. Signed-off-by:
-
Ville Syrjälä authored
We shouldn't restrict ourselves to just downclock modes with lower refresh rate than the preferred mode. Laptops these days can offer higher refresh rate modes as well. Remove the arbitrary limit and allow all modes that, apart from the clock, match the preferred mode. v2: s/add_edid_downclock_modes/add_edid_alt_fixed_modes/ (Jani) Signed-off-by:
-
Ville Syrjälä authored
Remove the "two fixed modes only" limit and grab as many downclock modes from the EDID as we can find. Signed-off-by:
-
Ville Syrjälä authored
Instead of duplicating the fixed/downclock modes we can just grab the originals straight from the probed_modes list and keep them. The next .get_modes() is going to repopulate the probed_modes list anyway so whatever we leave there is just going to sit around until that time wasting memory. In fact let's clear out the probed modes list entirely to make sure we get 100% consistent behaviour starting already from the very first real .get_modes(). Signed-off-by:
-
Ville Syrjälä authored
The intel_panel_add_edid_fixed_mode() vs. intel_panel_add_edid_downclock_mode() split is not really helpful. Let's just roll those into a single function so that the connector init code doesn't have to care too much about this. All we need to know is whether DRRS should be allowed or not. Signed-off-by:
-
Ville Syrjälä authored
intel_drrs_init() is a mostly pointless wrapper around intel_panel_add_edid_downclock_mode(), get rid of it. The only really useful thing left in there is the debug print regarding the DRRS type supported by the connector. Let's just move that into intel_panel_init(). Signed-off-by:
-
Ville Syrjälä authored
All the non-EDID fixed mode functions basically do the exact same thing. Let's refactor the common bits into a shared function. There are minor differences on how the mode types are populated, whether the display info physical size is updated, and the debug print. The differences are purely accidental, so unifying them is actually a good thing. Signed-off-by:
-
Ville Syrjälä authored
Rather than having the connector init get the fixed mode back from intel_panel and then feed it straight back into intel_panel_init() let's just make the fixed mode lookup put the mode directly onto the panel's fixed_modes list. Avoids the pointless round trip and opens the door for further enhancements to the fixed mode handling. v2: Make the debug message correct by using intel_panel_drrs_type() (Jani) Signed-off-by:
-
Ville Syrjälä authored
Pull all the eDP specific platform/port checks out from intel_drrs_init() into intel_edp_has_drrs(). Signed-off-by:
-
- 01 Apr, 2022 4 commits
-
-
José Roberto de Souza authored
This will make easy to extend MBUS joining support to future platforms that also supports this feature. Reviewed-by:
-
Jani Nikula authored
Clean up the massive i915_reg.h a bit with this isolated set of registers. v2: Remove stale comment (Lucas) Signed-off-by:
-
Jani Nikula authored
The macros are now only needed within intel_dmc.c, so move them there. Signed-off-by:
-
Jani Nikula authored
Only intel_dmc.c should be accessing dmc details directly. Need to add an i915_error_printf() stub for CONFIG_DRM_I915_CAPTURE_ERROR=n. v2: Add the stub (kernel test robot <lkp@intel.com>) Signed-off-by:
-
- 31 Mar, 2022 1 commit
-
-
Vinod Govindapillai authored
Update DG2 init bw info similar to other platforms even though DG2 has constant bandwidh. This will avoid branching out DG2 specific max bw calls. V3: Fix dg2_get_bw_info() and avoid handle special cases for DG2 (Ville Syrjälä) cc: Ville Syrjälä <ville.syrjala@linux.intel.com> cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by:Vinod Govindapillai <vinod.govindapillai@intel.com> Signed-off-by:
-
- 30 Mar, 2022 2 commits
-
-
José Roberto de Souza authored
PIPE_MBUS_DBOX_CTL was only being programmed when a pipe is being enabled but that could potentially cause issues as it could have mismatching values while pipes are being enabled. So here moving the PIPE_MBUS_DBOX_CTL programming of all pipes to be executed before the function that enables all pipes, leaving all pipes with a matching A_CREDIT value. While at it, also moving it to intel_pm.c as we are trying to reduce the gigantic size of intel_display.c and intel_pm.c have other MBUS programing sequences. v2: - do not program PIPE_MBUS_DBOX_CTL if pipe will not be active or when it do not needs modeset - remove the checks to wait a vblank v3: - checking if dbuf state is present in state before using it v4: - removing redundant checks - calling intel_atomic_get_new_dbuf_state instead of intel_atomic_get_dbuf_state BSpec: 49213 BSpec: 50343 Reviewed-by:
-
Caz Yokoyama authored
Alderlake-P has different MBUS DBOX BW and B credits than other platforms, so here setting it properly. BSpec: 49213 BSpec: 50343 Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Caz Yokoyama <caz.yokoyama@intel.com> Signed-off-by:
-
