Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on information from the ZTE Windows drivers.

Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

usb: fixes for v3.7-rc2

Here's the first set of fixes for v3.7-rc cycle.

DesignWare Core USB3 Driver (dwc3) got two fixes. The first one fixes a long
standing bug which would keep endpoint with BUSY flag set forever if we cancel
a transfer which has already been started by the controller. The second fix
will just switch PHYs back off when DWC3 driver is removed.

MUSB fixed a bug which would cause a Kernel Oops at least on AM3517 when
removing a device. For some reason that particular device can fall into a
situation where you have both Disconnect and Endpoint IRQs happen
simultaneously (have both bits set in IRQ_STATUS register) and, because
Disconnect Interrupt is handled before Endpoint Interrupts, we would try to
transfer data over a disconnected device, thus generating a kernel oops.

Renensas' USB DRD driver got two fixes which are a) fixing an off-by-one bug on
the pipe iterator implementation and b) fixing Interrupt Status Clear procedure
in order to properly clear a single Interrupt event without clearing (and
masking) other events we didn't handle yet.

This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.

System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure port data is initialised before creating sysfs attributes to
avoid a race.

A recent patch ("USB: io_ti: fix port-data memory leak") got the
sysfs-attribute creation and port-data initialisation ordering wrong.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure sysfs attributes are created at port probe.

A recent patch ("USB: iuu_phoenix: fix port-data memory leak") removed
the sysfs-attribute creation by mistake.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the write waitqueue was initialised but never used.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the write waitqueue was initialised but never used.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current code assumes that CSIZE is 0000060, which appears to be
wrong on some arches (such as powerpc).
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on arch-vt8500 when using devicetree.

Without this patch, arch-vt8500 cannot detect ehci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Device-tree probed devices don't get a dev.dma_mask set. This patch
sets a default 32bit mask on platforms using devicetree.

Without this patch, arch-vt8500 cannot detect uhci attached devices.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the write endpoint is interrupt type, usb_sndintpipe() should
be passed to usb_fill_int_urb() instead of usb_sndbulkpipe().

Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.

Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are no users of this macro anymore in the kernel tree, so finally
delete it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1615) fixes a bug in the Garmin USB serial driver.  It
uses attach, disconnect, and release routines to carry out actions
that should be handled by port_probe and port_remove routines, because
they access port-specific data.

The bug causes an oops when the device in unplugged, because the
private data for each port structure now gets erased when the port is
unbound from the driver, resulting in a null-pointer dereference.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported--by: Markus Schauler <mschauler@gmail.com>
Tested-by: Markus Schauler <mschauler@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by allocating and freeing port data in
port_probe/remove rather than in attach/release, and by introducing
serial private data to store the device type which is interface rather
than port specific.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port data memory leak by replacing port private data with serial
private data.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at
release.

The private data is used to store the control interface number, but as
this is the same for all ports on an interface it should be stored as
usb-serial data anyway.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the write waitqueue was initialised but never used.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.

Note that the write waitqueue was initialised but never used.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix NULL-pointer dereference at release by replacing attach and release
with port_probe and port_remove.

Since commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is NULL when release is called.

Compile-only tested.

Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The STOTG04 is an replacement for ISP1301.

Most of the registers on STOTG04 are the same as on ISP1301, but the
register ISP1301_I2C_OTG_CONTROL_2 (address 0x10) doesn't exist on the
ST part.

This is a work around for this by using the interrupt source register that
should behave the same on both parts and has the needed information.
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When interrupt happened, renesas_usbhs driver gets irq status
by usbhs_status_get_each_irq(), and cleared all status by using 0.
But, this method is incorrect,
since extra interrupt might occur between them.
This patch cleared corresponding bits only
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

__usbhs_for_each_pipe() is the macro which moves around each pipe,
but it has a bug which didn't care about 1st pipe's position.
Because of this bug, it moves around
pipe0, pipe2, pipe3 ... even though it requested pipe1, pipe2, pipe3...
This patch modifies it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Composite gadget support is now available as a library instead of being
built with each gadget. Composite drivers need to select
USB_LIBCOMPOSITE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We call usb_phy_init() from dwc3_core_init() during
probe, so adding usb_phy_shutdown() to dwc3_core_exit()
while removing the device so we don't keep PHYs
turned on, consuming power, unnecessarily.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

On AM3517, tx and rx interrupt are detected together with
the disconnect event. This generates a kernel panic in musb_interrupt,
because rx / tx are handled after disconnect.
This issue was seen on a Technexion's TAM3517 SOM. Unplugging a device,
tx / rx interrupts together with disconnect are detected. This brings
to kernel panic like this:

[   68.526153] Unable to handle kernel NULL pointer dereference at virtual address 00000011
[   68.534698] pgd = c0004000
[   68.537536] [00000011] *pgd=00000000
[   68.541351] Internal error: Oops: 17 [#1] ARM
[   68.545928] Modules linked in:
[   68.549163] CPU: 0    Not tainted  (3.6.0-rc5-00020-g9e05905 #178)
[   68.555694] PC is at rxstate+0x8/0xdc
[   68.559539] LR is at musb_interrupt+0x98/0x858
[   68.564239] pc : [<c035cd88>]    lr : [<c035af1c>]    psr: 40000193
[   68.564239] sp : ce83fb40  ip : d0906410  fp : 00000000
[   68.576293] r10: 00000000  r9 : cf3b0e40  r8 : 00000002
[   68.581817] r7 : 00000019  r6 : 00000001  r5 : 00000001  r4 : 000000d4
[   68.588684] r3 : 00000000  r2 : 00000000  r1 : ffffffcc  r0 : cf23c108
[   68.595550] Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment ke

Note: this behavior is not seen with a USB hub, while it is
easy to reproduce connecting a USB-pen directly to the USB-A of
the board.

Drop tx / rx interrupts if disconnect is detected.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org # 3.5 3.6
Tested-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If a USB transfer has already been started, meaning
we have already issued StartTransfer command to that
particular endpoint, DWC3_EP_BUSY flag has also
already been set.

When we try to cancel this transfer which is already
in controller's cache, we will not receive XferComplete
event and we must clear DWC3_EP_BUSY in order to allow
subsequent requests to be properly started.

The best place to clear that flag is right after issuing
DWC3_DEPCMD_ENDTRANSFER.

Cc: stable@vger.kernel.org # v3.4 v3.5 v3.6
Reported-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Sync up to a known-good point in Linus's tree to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>