SATA PHY needs a new compatible ID. Add it to the DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add wakeup, system and reference clocks to DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When the request length is aligned to maxpacketsize, sometimes
the return length ret > the user space requested len.

At that time, we will use min_t(size_t, ret, len) to limit the
size in case of user data buffer overflow.

But we need return the min_t(size_t, ret, len) to tell the user
space rightly also.

[ balbi@ti.com: also fix comment's indentation ]
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

According to:"On-The-Go and Embedded Host Supplement to the USB Revision 2.0
Specification July 27, 2012 Revision 2.0 version 1.1a"
- From a_host to a_wait_bcon if !b_conn
- Add transition from a_host to a_wait_vfall if id state is high or a_bus_drop
- From a_wait_vfall to a_idle if a_wait_vfall_tmout
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In order to reduce the interrupt times in the embedded system,
a receiving workqueue is introduced.
This modification also enhanced the overall throughput as the
benefits of reducing interrupt occurrence.

This work was derived from previous work:
u_ether: move hardware transmit to RX workqueue.
Which should be base on codeaurora's work.

However, the benchmark on my platform shows the throughput
with workqueue is slightly better than NAPI.
Signed-off-by: Weinn Jheng <clanlab.proj@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We know what "value" is and it upsets static checkers that we appear to
have doubts about it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

These were cut and paste from the ->disconnect function.

Fixes commit 30d577b9bcc4 ('usb: dwc3: gadget: call gadget driver's
->suspend/->resume')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move omap-control binding information to the right location.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This reworks the way SuperSpeed descriptors are added and instead of
having a magic after full and high speed descriptors, it reworks the
whole descriptors block to include a flags field which lists which
descriptors are present and makes future extensions possible.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Allow userspace to pass SuperSpeed descriptors and
handle them in the driver accordingly.
This change doesn't modify existing desc_header and thereby
keeps the ABI changes backward compatible i.e. existing
userspace drivers compiled with old header (functionfs.h)
would continue to work with the updated kernel.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

commit 511f3c53 (usb: gadget: udc-core: fix a regression during gadget driver
unbinding) introduced a crash when DEBUG is enabled.

The debug trace in the atmel_usba_stop function made the assumption that the
driver pointer passed in parameter was not NULL, but since the commit above,
such assumption was no longer always true.

This commit now uses the driver pointer stored in udc which fixes this
issue.

[ balbi@ti.com : improved commit log a bit ]

Cc: <stable@vger.kernel.org> # v3.2+
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If no endpoints are present in the device tree, the kernel will crash with the
following error:

Unable to handle kernel paging request at virtual address 00101008
[...]
[<c0222ff4>] (composite_dev_prepare) from [<c022326c>] (composite_bind+0x5c/0x190)
[<c022326c>] (composite_bind) from [<c021ff8c>] (udc_bind_to_driver+0x48/0xf0)
[<c021ff8c>] (udc_bind_to_driver) from [<c02208e0>] (usb_gadget_probe_driver+0x7c/0xa0)
[<c02208e0>] (usb_gadget_probe_driver) from [<c0008970>] (do_one_initcall+0x94/0x140)
[<c0008970>] (do_one_initcall) from [<c04b4b50>] (kernel_init_freeable+0xec/0x1b4)
[<c04b4b50>] (kernel_init_freeable) from [<c0376cc4>] (kernel_init+0x8/0xe4)
[<c0376cc4>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
Code: e5950014 e1a04001 e5902008 e3a010d0 (e5922008)
---[ end trace 35c74bdd89b373d0 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b

This checks for that case and returns an error, not allowing the driver to be
loaded with no endpoints.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

After clear portsc.phcd, PHY needs 200us stable time for switch
32K clock to AHB clock.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We need this to keep PHY's power on or off during the system
suspend mode. If we need to enable USB wakeup, then we
must keep PHY's power being on during the system suspend mode.
Otherwise, we need to keep PHY's power being off to save power.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When we need the PHY can be waken up by external signals,
we can call this API. Besides, we call mxs_phy_disconnect_line
at this API to close the connection between USB PHY and
controller, after that, the line state from controller is SE0.
Once the PHY is out of power, without calling mxs_phy_disconnect_line,
there are unknown wakeups due to dp/dm floating at device mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This API is used to set wakeup enable at PHY registers, in that
case, the PHY can be waken up from suspend due to external events,
like vbus change, dp/dm change and id change.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It is used to access un-regulator registers according to
different controllers.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Two PHY bugs are fixed by IC logic, but these bits are not
enabled by default, so we enable them at driver.
The two bugs are: MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST
which are described at code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Change "high speed" to "HS"
Change "non-high speed" to "FS/LS"

Implementation of notify_suspend and notify_resume will be different
according to mxs_phy_data->flags.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It is needed by imx6 SoC series, but not for imx23 and imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add anatop phandle which is used to access anatop registers to
control PHY's power and other USB operations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The auto setting is used to open related power and clocks
automatically after receiving wakeup signal.

With this feature, the PHY's clock and power can be recovered
correctly from low power mode, it is guaranteed by IC logic.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The mxs-phy has several bugs and features at different
versions, the driver code can get it through of_device_id.data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add "fsl,imx6q-usbphy" for imx6dq and imx6dl, add
"fsl,imx6sl-usbphy" for imx6sl, and "fsl,imx23-usbphy"
is still a fallback for other strings.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds suspend/resume support to s3c-hsotg driver. It makes UDC
driver more power efficient.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Reprogramming the DMA after tear down is initiated leads to warning.
This is mainly seen with ISOCH since we do a delayed completion for
ISOCH transfers. In ISOCH transfers dma_completion should not reprogram
if the channel tear down is initiated.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().

However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since PHYs for dwc3 is optional (not all SoCs having PHYs for DWC3
should be programmed), do not return from probe if the USB PHY library
returns -ENODEV as that indicates the platform does not have a
programmable PHY.

While this can be considered as a temporary fix, a long term solution
would be to add 'nop' PHY for platforms that does not have programmable
PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since now we have a separate folder for phy, move the PHY dt binding
documentation of TI to that folder.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>

commit 388e5c51 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.

Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

we need to pre-start stream transfers otherwise we
will never know when to start them.
Signed-off-by: Felipe Balbi <balbi@ti.com>

When going into bus suspend/resume we _must_
call gadget driver's ->suspend/->resume callbacks
accordingly. This patch implements that very feature
which has been missing forever.
Signed-off-by: Felipe Balbi <balbi@ti.com>

It's not always we need to force a transfer to be removed
from the core's internal cache. This extra argument will
help differentiating those two cases.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

During superspeed, HIRD threshold should always
be zero. Curent driver wasn't making sure that
was the case.
Signed-off-by: Felipe Balbi <balbi@ti.com>

if we have hibernation configured, Databook
instructs us to set KEEP_CONNECT bit together
with RUN_STOP bit, in step 9 of section 12.3.6.1
Initialization for Hibernation Support.
Signed-off-by: Felipe Balbi <balbi@ti.com>

no functional changes, just converting spaces
into tab.
Signed-off-by: Felipe Balbi <balbi@ti.com>

We must read HWPARAMS4 register to figure out
how many scratch buffers we should allocate.

Later patch will use "Set Scratchpad Buffer
Array" command to pass the pointer to the
IP so it can be used during hibernation.
Signed-off-by: Felipe Balbi <balbi@ti.com>

That argument will be used in later patches when we
have working hibernation support. For now, always
pass it as false.

The idea of this patch is to decrease to size of
following patches and slowly add hibernation building
blocks to the gadget side of dwc3 so that it becomes
very easy to review the actual hibernation code.

[ balbi@ti.com : rewrote patch on top of current
	tree. Added commit log. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>