- 12 Dec, 2022 40 commits
-
-
Hans J. Schultz authored
When an ATU violation occurs, the switch uses the ATU FID register to report the FID of the MAC address that incurred the violation. It would be good for the driver to know the FID value for purposes such as logging and CPU-based authentication. Up until now, the driver has been calling the mv88e6xxx_g1_atu_op() function to read ATU violations, but that doesn't do exactly what we want, namely it calls mv88e6xxx_g1_atu_fid_write() with FID 0. (side note, the documentation for the ATU Get/Clear Violation command says that writes to the ATU FID register have no effect before the operation starts, it's only that we disregard the value that this register provides once the operation completes) So mv88e6xxx_g1_atu_fid_write() is not what we want, but rather mv88e6xxx_g1_atu_fid_read(). However, the latter doesn't exist, we need to write it. The remainder of mv88e6xxx_g1_atu_op() except for mv88e6xxx_g1_atu_fid_write() is still needed, namely to send a GET_CLR_VIOLATION command to the ATU. In principle we could have still kept calling mv88e6xxx_g1_atu_op(), but the MDIO writes to the ATU FID register are pointless, but in the interest of doing less CPU work per interrupt, write a new function called mv88e6xxx_g1_read_atu_violation() and call it. The FID will be the port default FID as set by mv88e6xxx_port_set_fid() if the VID from the packet cannot be found in the VTU. Otherwise it is the FID derived from the VTU entry associated with that VID. Signed-off-by:
Hans J. Schultz <netdev@kapio-technology.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vladimir Oltean authored
Currently, the MV88E6XXX_PORT_ASSOC_VECTOR_INT_AGE_OUT bit (interrupt on age out) is not enabled by the driver, and as a result, the print for age out violations is dead code. Remove it until there is some way for this to be triggered. Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'for-net-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Luiz Augusto von Dentz says: ==================== bluetooth-next pull request for net-next: - Add a new VID/PID 0489/e0f2 for MT7922 - Add Realtek RTL8852BE support ID 0x0cb8:0xc559 - Add a new PID/VID 13d3/3549 for RTL8822CU - Add support for broadcom BCM43430A0 & BCM43430A1 - Add CONFIG_BT_HCIBTUSB_POLL_SYNC - Add CONFIG_BT_LE_L2CAP_ECRED - Add support for CYW4373A0 - Add support for RTL8723DS - Add more device IDs for WCN6855 - Add Broadcom BCM4377 family PCIe Bluetooth * tag 'for-net-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (51 commits) Bluetooth: Wait for HCI_OP_WRITE_AUTH_PAYLOAD_TO to complete Bluetooth: ISO: Avoid circular locking dependency Bluetooth: RFCOMM: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: hci_core: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: hci_bcsp: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: hci_h5: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: hci_ll: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: hci_qca: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: btusb: don't call kfree_skb() under spin_lock_irqsave() Bluetooth: btintel: Fix missing free skb in btintel_setup_combined() Bluetooth: hci_conn: Fix crash on hci_create_cis_sync Bluetooth: btintel: Fix existing sparce warnings Bluetooth: btusb: Fix existing sparce warning Bluetooth: btusb: Fix new sparce warnings Bluetooth: btusb: Add a new PID/VID 13d3/3549 for RTL8822CU Bluetooth: btusb: Add Realtek RTL8852BE support ID 0x0cb8:0xc559 dt-bindings: net: realtek-bluetooth: Add RTL8723DS Bluetooth: btusb: Add a new VID/PID 0489/e0f2 for MT7922 dt-bindings: bluetooth: broadcom: add BCM43430A0 & BCM43430A1 Bluetooth: hci_bcm4377: Fix missing pci_disable_device() on error in bcm4377_probe() ... ==================== Link: https://lore.kernel.org/r/20221212222322.1690780-1-luiz.dentz@gmail.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-nextJakub Kicinski authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS updates for net-next 1) Incorrect error check in nft_expr_inner_parse(), from Dan Carpenter. 2) Add DATA_SENT state to SCTP connection tracking helper, from Sriram Yagnaraman. 3) Consolidate nf_confirm for ipv4 and ipv6, from Florian Westphal. 4) Add bitmask support for ipset, from Vishwanath Pai. 5) Handle icmpv6 redirects as RELATED, from Florian Westphal. 6) Add WARN_ON_ONCE() to impossible case in flowtable datapath, from Li Qiong. 7) A large batch of IPVS updates to replace timer-based estimators by kthreads to scale up wrt. CPUs and workload (millions of estimators). Julian Anastasov says: This patchset implements stats estimation in kthread context. It replaces the code that runs on single CPU in timer context every 2 seconds and causing latency splats as shown in reports [1], [2], [3]. The solution targets setups with thousands of IPVS services, destinations and multi-CPU boxes. Spread the estimation on multiple (configured) CPUs and multiple time slots (timer ticks) by using multiple chains organized under RCU rules. When stats are not needed, it is recommended to use run_estimation=0 as already implemented before this change. RCU Locking: - As stats are now RCU-locked, tot_stats, svc and dest which hold estimator structures are now always freed from RCU callback. This ensures RCU grace period after the ip_vs_stop_estimator() call. Kthread data: - every kthread works over its own data structure and all such structures are attached to array. For now we limit kthreads depending on the number of CPUs. - even while there can be a kthread structure, its task may not be running, eg. before first service is added or while the sysctl var is set to an empty cpulist or when run_estimation is set to 0 to disable the estimation. - the allocated kthread context may grow from 1 to 50 allocated structures for timer ticks which saves memory for setups with small number of estimators - a task and its structure may be released if all estimators are unlinked from its chains, leaving the slot in the array empty - every kthread data structure allows limited number of estimators. Kthread 0 is also used to initially calculate the max number of estimators to allow in every chain considering a sub-100 microsecond cond_resched rate. This number can be from 1 to hundreds. - kthread 0 has an additional job of optimizing the adding of estimators: they are first added in temp list (est_temp_list) and later kthread 0 distributes them to other kthreads. The optimization is based on the fact that newly added estimator should be estimated after 2 seconds, so we have the time to offload the adding to chain from controlling process to kthread 0. - to add new estimators we use the last added kthread context (est_add_ktid). The new estimators are linked to the chains just before the estimated one, based on add_row. This ensures their estimation will start after 2 seconds. If estimators are added in bursts, common case if all services and dests are initially configured, we may spread the estimators to more chains and as result, reducing the initial delay below 2 seconds. Many thanks to Jiri Wiesner for his valuable comments and for spending a lot of time reviewing and testing the changes on different platforms with 48-256 CPUs and 1-8 NUMA nodes under different cpufreq governors. The new IPVS estimators do not use workqueue infrastructure because: - The estimation can take long time when using multiple IPVS rules (eg. millions estimator structures) and especially when box has multiple CPUs due to the for_each_possible_cpu usage that expects packets from any CPU. With est_nice sysctl we have more control how to prioritize the estimation kthreads compared to other processes/kthreads that have latency requirements (such as servers). As a benefit, we can see these kthreads in top and decide if we will need some further control to limit their CPU usage (max number of structure to estimate per kthread). - with kthreads we run code that is read-mostly, no write/lock operations to process the estimators in 2-second intervals. - work items are one-shot: as estimators are processed every 2 seconds, they need to be re-added every time. This again loads the timers (add_timer) if we use delayed works, as there are no kthreads to do the timings. [1] Report from Yunhong Jiang: https://lore.kernel.org/netdev/D25792C1-1B89-45DE-9F10-EC350DC04ADC@gmail.com/ [2] https://marc.info/?l=linux-virtual-server&m=159679809118027&w=2 [3] Report from Dust: https://archive.linuxvirtualserver.org/html/lvs-devel/2020-12/msg00000.html * git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next: ipvs: run_estimation should control the kthread tasks ipvs: add est_cpulist and est_nice sysctl vars ipvs: use kthreads for stats estimation ipvs: use u64_stats_t for the per-cpu counters ipvs: use common functions for stats allocation ipvs: add rcu protection to stats netfilter: flowtable: add a 'default' case to flowtable datapath netfilter: conntrack: set icmpv6 redirects as RELATED netfilter: ipset: Add support for new bitmask parameter netfilter: conntrack: merge ipv4+ipv6 confirm functions netfilter: conntrack: add sctp DATA_SENT state netfilter: nft_inner: fix IS_ERR() vs NULL check ==================== Link: https://lore.kernel.org/r/20221211101204.1751-1-pablo@netfilter.orgSigned-off-by: -
Luiz Augusto von Dentz authored
This make sure HCI_OP_WRITE_AUTH_PAYLOAD_TO completes before notifying the encryption change just as is done with HCI_OP_READ_ENC_KEY_SIZE. Signed-off-by:Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
Luiz Augusto von Dentz authored
This attempts to avoid circular locking dependency between sock_lock and hdev_lock: WARNING: possible circular locking dependency detected 6.0.0-rc7-03728-g18dd8ab0a783 #3 Not tainted ------------------------------------------------------ kworker/u3:2/53 is trying to acquire lock: ffff888000254130 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}, at: iso_conn_del+0xbd/0x1d0 but task is already holding lock: ffffffff9f39a080 (hci_cb_list_lock){+.+.}-{3:3}, at: hci_le_cis_estabilished_evt+0x1b5/0x500 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (hci_cb_list_lock){+.+.}-{3:3}: __mutex_lock+0x10e/0xfe0 hci_le_remote_feat_complete_evt+0x17f/0x320 hci_event_packet+0x39c/0x7d0 hci_rx_work+0x2bf/0x950 process_one_work+0x569/0x980 worker_thread+0x2a3/0x6f0 kthread+0x153/0x180 ret_from_fork+0x22/0x30 -> #1 (&hdev->lock){+.+.}-{3:3}: __mutex_lock+0x10e/0xfe0 iso_connect_cis+0x6f/0x5a0 iso_sock_connect+0x1af/0x710 __sys_connect+0x17e/0x1b0 __x64_sys_connect+0x37/0x50 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x62/0xcc -> #0 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: __lock_acquire+0x1b51/0x33d0 lock_acquire+0x16f/0x3b0 lock_sock_nested+0x32/0x80 iso_conn_del+0xbd/0x1d0 iso_connect_cfm+0x226/0x680 hci_le_cis_estabilished_evt+0x1ed/0x500 hci_event_packet+0x39c/0x7d0 hci_rx_work+0x2bf/0x950 process_one_work+0x569/0x980 worker_thread+0x2a3/0x6f0 kthread+0x153/0x180 ret_from_fork+0x22/0x30 other info that might help us debug this: Chain exists of: sk_lock-AF_BLUETOOTH-BTPROTO_ISO --> &hdev->lock --> hci_cb_list_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(hci_cb_list_lock); lock(&hdev->lock); lock(hci_cb_list_lock); lock(sk_lock-AF_BLUETOOTH-BTPROTO_ISO); *** DEADLOCK *** 4 locks held by kworker/u3:2/53: #0: ffff8880021d9130 ((wq_completion)hci0#2){+.+.}-{0:0}, at: process_one_work+0x4ad/0x980 #1: ffff888002387de0 ((work_completion)(&hdev->rx_work)){+.+.}-{0:0}, at: process_one_work+0x4ad/0x980 #2: ffff888001ac0070 (&hdev->lock){+.+.}-{3:3}, at: hci_le_cis_estabilished_evt+0xc3/0x500 #3: ffffffff9f39a080 (hci_cb_list_lock){+.+.}-{3:3}, at: hci_le_cis_estabilished_evt+0x1b5/0x500 Signed-off-by: -
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 81be03e0 ("Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 9238f36a ("Bluetooth: Add request cmd_complete and cmd_status functions") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 43eb12d7 ("Bluetooth: Fix/implement Three-wire reliable packet sending") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 166d2f6a ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 0ff252c1 ("Bluetooth: hciuart: Add support QCA chipset for UART") Signed-off-by:
-
Yang Yingliang authored
It is not allowed to call kfree_skb() from hardware interrupt context or with interrupts being disabled. So replace kfree_skb() with dev_kfree_skb_irq() under spin_lock_irqsave(). Fixes: 803b5836 ("Bluetooth: btusb: Implement driver internal packet reassembly") Signed-off-by:
-
Wang ShaoBo authored
skb allocated by __hci_cmd_sync would not be used whether in checking for supported iBT hardware variants or after, we should free it in all error branches, this patch makes the case read version failed or default error case free skb before return. Fixes: c86c7285 ("Bluetooth: btintel: Fix the legacy bootloader returns tlv based version") Fixes: 019a1caa ("Bluetooth: btintel: Refactoring setup routine for bootloader devices") Signed-off-by:
Wang ShaoBo <bobo.shaobowang@huawei.com> Reviewed-by:
Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
When attempting to connect multiple ISO sockets without using DEFER_SETUP may result in the following crash: BUG: KASAN: null-ptr-deref in hci_create_cis_sync+0x18b/0x2b0 Read of size 2 at addr 0000000000000036 by task kworker/u3:1/50 CPU: 0 PID: 50 Comm: kworker/u3:1 Not tainted 6.0.0-rc7-02243-gb84a13ff4eda #4373 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-1.fc36 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl+0x19/0x27 kasan_report+0xbc/0xf0 ? hci_create_cis_sync+0x18b/0x2b0 hci_create_cis_sync+0x18b/0x2b0 ? get_link_mode+0xd0/0xd0 ? __ww_mutex_lock_slowpath+0x10/0x10 ? mutex_lock+0xe0/0xe0 ? get_link_mode+0xd0/0xd0 hci_cmd_sync_work+0x111/0x190 process_one_work+0x427/0x650 worker_thread+0x87/0x750 ? process_one_work+0x650/0x650 kthread+0x14e/0x180 ? kthread_exit+0x50/0x50 ret_from_fork+0x22/0x30 </TASK> Fixes: 26afbd82 ("Bluetooth: Add initial implementation of CIS connections") Signed-off-by:
-
Luiz Augusto von Dentz authored
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btintel.c:1041:38: warning: cast to restricted __le32 drivers/bluetooth/btintel.c:1786:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1795:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1796:25: warning: cast to restricted __le16 drivers/bluetooth/btintel.c:1797:25: warning: cast to restricted __le16 Signed-off-by: -
Luiz Augusto von Dentz authored
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btusb.c:3426:28: warning: cast to restricted __le32 Signed-off-by: -
Luiz Augusto von Dentz authored
This fix the following warnings detect with make W=1 C=1: drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16 drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16 Signed-off-by: -
Gongwei Li authored
* /sys/kernel/debug/usb/devices T: Bus=03 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=b85b Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Gongwei Li <ligongwei@kylinos.cn> Signed-off-by:
-
Artem Lukyanov authored
Add the support ID(0x0cb8, 0xc559) to usb_device_id table for Realtek RTL8852BE. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cb8 ProdID=c559 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Artem Lukyanov <dukzcry@ya.ru> Signed-off-by:
-
Samuel Holland authored
RTL8723DS is another variant of the RTL8723 WiFi + Bluetooth chip. It is already supported by the hci_uart/btrtl driver. Document the compatible. Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Alistair Francis <alistair@alistair23.me> Signed-off-by:
Samuel Holland <samuel@sholland.org> Signed-off-by:
-
Andy Chi authored
Add VID/PID 0489/e0f2 for MediaTek MT7922 Bluetooth chip. Found and tested with HP ProBook. From /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f2 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by:
Andy Chi <andy.chi@canonical.com> Signed-off-by:
-
Luca Weiss authored
Document the compatible string for BCM43430A0 bluetooth used in lg-lenok and BCM43430A1 used in asus-sparrow. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
-
Yang Yingliang authored
pci_disable_device() need be called while module exiting, switch to use pcim_enable(), pci_disable_device() will be called in pcim_release() after probe() failure. Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards") Signed-off-by:Sven Peter <sven@svenpeter.dev> Signed-off-by:
-
Raman Varabets authored
Identifies as "Realtek Bluetooth Radio"; used in UGREEN CM390 (P/N 80889). Device description at /sys/kernel/debug/usb/devices: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2b89 ProdID=8761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Raman Varabets <linux-bluetooth@cyborgize.sg> Signed-off-by:
-
Sven Peter authored
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple machines. This driver adds support for the Bluetooth function which exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic. Signed-off-by:
-
Sven Peter authored
Broadcom 4378/4387 controllers found in Apple Silicon Macs claim to support getting MWS Transport Layer Configuration, < HCI Command: Read Local Supported... (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) [...] Get MWS Transport Layer Configuration (Octet 30 - Bit 3)] [...] , but then don't actually allow the required command: > HCI Event: Command Complete (0x0e) plen 15 Get MWS Transport Layer Configuration (0x05|0x000c) ncmd 1 Status: Command Disallowed (0x0c) Number of transports: 0 Baud rate list: 0 entries 00 00 00 00 00 00 00 00 00 00 Signed-off-by: -
Sven Peter authored
Broadcom 4377 controllers found in Apple x86 Macs with the T2 chip claim to support extended scanning when querying supported states, < HCI Command: LE Read Supported St.. (0x08|0x001c) plen 0 > HCI Event: Command Complete (0x0e) plen 12 LE Read Supported States (0x08|0x001c) ncmd 1 Status: Success (0x00) States: 0x000003ffffffffff [...] LE Set Extended Scan Parameters (Octet 37 - Bit 5) LE Set Extended Scan Enable (Octet 37 - Bit 6) [...] , but then fail to actually implement the extended scanning: < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Unknown HCI Command (0x01) Signed-off-by: -
Sven Peter authored
Broadcom controllers present on Apple Silicon devices use the upper 8 bits of the event type in the LE Extended Advertising Report for the channel on which the frame has been received. These bits are reserved according to the Bluetooth spec anyway such that we can just drop them to ensure that the advertising results are parsed correctly. The following excerpt from a btmon trace shows a report received on channel 37 by these controllers: > HCI Event: LE Meta Event (0x3e) plen 55 LE Extended Advertising Report (0x0d) Num reports: 1 Entry 0 Event type: 0x2513 Props: 0x0013 Connectable Scannable Use legacy advertising PDUs Data status: Complete Reserved (0x2500) Legacy PDU Type: Reserved (0x2513) Address type: Public (0x00) Address: XX:XX:XX:XX:XX:XX (Shenzhen Jingxun Software [...]) Primary PHY: LE 1M Secondary PHY: No packets SID: no ADI field (0xff) TX power: 127 dBm RSSI: -76 dBm (0xb4) Periodic advertising interval: 0.00 msec (0x0000) Direct address type: Public (0x00) Direct address: 00:00:00:00:00:00 (OUI 00-00-00) Data length: 0x1d [...] Flags: 0x18 Simultaneous LE and BR/EDR (Controller) Simultaneous LE and BR/EDR (Host) Company: Harman International Industries, Inc. (87) Data: [...] Service Data (UUID 0xfddf): Name (complete): JBL Flip 5 Signed-off-by: -
Sven Peter authored
Add bluetooth controller nodes and the required brcm,board-type properties to be able to select the correct firmware to all board device trees. Signed-off-by:
-
Sven Peter authored
These chips are combined Wi-Fi/Bluetooth radios which expose a PCI subfunction for the Bluetooth part. They are found in Apple machines such as the x86 models with the T2 chip or the arm64 models with the M1 or M2 chips. Signed-off-by:
-
Sven Peter authored
Bluetooth controllers share the common local-bd-address property. Add a generic YAML schema to replace bluetooth.txt for those. Signed-off-by:
-
Marek Vasut authored
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress. This chip is present e.g. on muRata 2AE module. This chip has additional quirk where the HCI command 0xfc45, used on older chips to switch UART clock from 24 MHz to 48 MHz, to support baudrates over 3 Mbdps, is no longer recognized by this newer chip. This newer chip can configure the 4 Mbdps baudrate without the need to issue HCI command 0xfc45, so add flag to indicate this and do not issue the command on this chip to avoid failure to set 4 Mbdps baud rate. It is not clear whether there is a way to determine which chip does and which chip does not support the HCI command 0xfc45, other than trial and error. Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Marek Vasut authored
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress. This chip is present e.g. on muRata 2AE module. Extend the binding with its DT compatible. Acked-by:
-
Kang Minchul authored
Replace kmalloc+memset by kzalloc for better readability and simplicity. This addresses the cocci warning below: WARNING: kzalloc should be used for d, instead of kmalloc/memset Signed-off-by:
Kang Minchul <tegongkang@gmail.com> Signed-off-by:
-
Shengyu Qu authored
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10) Windows driver download address: https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/ thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads /driver-list/ Signed-off-by:
Shengyu Qu <wiagn233@outlook.com> Signed-off-by:
-
Christophe JAILLET authored
'err' is known to be <0 at this point. So, some cases can not be reached because of a missing "-". Add it. Fixes: ca2045e0 ("Bluetooth: Add bt_status") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Luiz Augusto von Dentz authored
This adds CONFIG_BT_LE_L2CAP_ECRED which can be used to enable L2CAP Enhanced Credit Flow Control Mode by default, previously it was only possible to set it via module parameter (e.g. bluetooth.enable_ecred=1). Since L2CAP ECRED mode is required by the likes of EATT which is recommended for LE Audio this enables it by default. Signed-off-by:
-
Luiz Augusto von Dentz authored
poll_sync has been proven to fix races of USB data and event endpoints so this enables it by default. Signed-off-by:
-
Luiz Augusto von Dentz authored
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the default behavior of Bluetooth USB controller with respect to poll synchronization of its endpoits. Signed-off-by:
-
