- 15 Mar, 2016 9 commits
-
-
Hans Verkuil authored
commit 0ba4581c upstream. The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70 again after it has already been cleared. Instead it should use the cached irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since this has already been done. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Liad Kaufman authored
commit fb896c44 upstream. Until this patch, when TXing non-sta the pending_frames counter wasn't increased, but it WAS decreased in iwl_mvm_rx_tx_cmd_single(), what makes it negative in certain conditions. This in turn caused much trouble when we need to remove the station since we won't be waiting forever until pending_frames gets 0. In certain cases, we were exhausting the station table even in BSS mode, because we had a lot of stale stations. Increase the counter also in iwl_mvm_tx_skb_non_sta() after a successful TX to avoid this outcome. Signed-off-by:
Liad Kaufman <liad.kaufman@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> [ kamal: backport to 4.2: file rename ] Signed-off-by:
-
Arnd Bergmann authored
commit 287e6611 upstream. As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not work correctly in compat mode with libata. I have investigated the issue further and found multiple problems that all appeared with the same commit that originally introduced HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy a 'long' variable containing either 0 or 1 to user space. The problems with this are: * On big-endian machines, this will always write a zero because it stores the wrong byte into user space. * In compat mode, the upper three bytes of the variable are updated by the compat_hdio_ioctl() function, but they now contain uninitialized stack data. * The hdparm tool calling this ioctl uses a 'static long' variable to store the result. This means at least the upper bytes are initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT would fill them with data that remains stale when the low byte is overwritten. Fortunately libata doesn't implement any of the affected ioctl commands, so this would only happen when we query both an IDE and an ATA device in the same command such as "hdparm -N -c /dev/hda /dev/sda" * The libata code for unknown reasons started using ATA_IOC_GET_IO32 and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT, while the ioctl commands that were added later use the normal HDIO_* names. This is harmless but rather confusing. This addresses all four issues by changing the code to use put_user() on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem does, and by clarifying the names of the ioctl commands. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reported-by:
Soohoon Lee <Soohoon.Lee@f5.com> Tested-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Sven Eckelmann authored
commit 212c5a5e upstream. The change from cur_tp to the function minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the current throughput. For example in minstrel_ht the correct conversion between them would be: mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..). This factor 10 must also be included in the calculation of minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing algorithms like B.A.T.M.A.N. V will make incorrect decision based on these values. Its kernel based implementation expects expected_throughput always to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps]. The same requirement has iw or olsrdv2's nl80211 based statistics module which retrieve the same data via NL80211_STA_INFO_TX_BITRATE. Fixes: 6a27b2c4 ("mac80211: restructure per-rate throughput calculation into function") Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Chris Bainbridge authored
commit f39ea269 upstream. Use kzalloc instead of kmalloc for struct tid_ampdu_rx to initialize the "removed" field (all others are initialized manually). That fixes: UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29 load of value 2 is not a valid value for type '_Bool' CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265 Workqueue: phy0 rt2x00usb_work_rxdone 0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007 ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500 ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032 Call Trace: [<ffffffff8181d866>] dump_stack+0x45/0x5f [<ffffffff8188422d>] ubsan_epilogue+0xd/0x40 [<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70 [<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730 [<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00 [<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750 [<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990 While at it, convert to use sizeof(*tid_agg_rx) instead. Fixes: 788211d8 ("mac80211: fix RX A-MPDU session reorder timer deletion") Signed-off-by:
Chris Bainbridge <chris.bainbridge@gmail.com> [reword commit message, use sizeof(*tid_agg_rx)] Signed-off-by:
-
Johannes Berg authored
commit cb150b9d upstream. Since cfg80211 frequently takes actions from its netdev notifier call, wireless extensions messages could still be ordered badly since the wext netdev notifier, since wext is built into the kernel, runs before the cfg80211 netdev notifier. For example, the following can happen: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether when setting the interface down causes the wext message. To also fix this, export the wireless_nlevent_flush() function and also call it from the cfg80211 notifier. Signed-off-by:
-
Johannes Berg authored
commit 8bf86273 upstream. Beniamino reported that he was getting an RTM_NEWLINK message for a given interface, after the RTM_DELLINK for it. It turns out that the message is a wireless extensions message, which was sent because the interface had been connected and disconnection while it was deleted caused a wext message. For its netlink messages, wext uses RTM_NEWLINK, but the message is without all the regular rtnetlink attributes, so "ip monitor link" prints just rudimentary information: 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff 5: wlan1: <BROADCAST,MULTICAST,UP> link/ether (from my hwsim reproduction) This can cause userspace to get confused since it doesn't expect an RTM_NEWLINK message after RTM_DELLINK. The reason for this is that wext schedules a worker to send out the messages, and the scheduling delay can cause the messages to get out to userspace in different order. To fix this, have wext register a netdevice notifier and flush out any pending messages when netdevice state changes. This fixes any ordering whenever the original message wasn't sent by a notifier itself. Reported-by:
Beniamino Galvani <bgalvani@redhat.com> Signed-off-by:
-
Vladis Dronov authored
commit 8e20cf2b upstream. The aiptek driver crashes in aiptek_probe() when a specially crafted USB device without endpoints is detected. This fix adds a check that the device has proper configuration expected by the driver. Also an error return value is changed to more matching one in one of the error paths. Reported-by:
Ralf Spenneberg <ralf@spenneberg.net> Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Martin Schwidefsky authored
commit 3446c13b upstream. The fork of a process with four page table levels is broken since git commit 6252d702 "[S390] dynamic page tables." All new mm contexts are created with three page table levels and an asce limit of 4TB. If the parent has four levels dup_mmap will add vmas to the new context which are outside of the asce limit. The subsequent call to copy_page_range will walk the three level page table structure of the new process with non-zero pgd and pud indexes. This leads to memory clobbers as the pgd_index *and* the pud_index is added to the mm->pgd pointer without a pgd_deref in between. The init_new_context() function is selecting the number of page table levels for a new context. The function is used by mm_init() which in turn is called by dup_mm() and mm_alloc(). These two are used by fork() and exec(). The init_new_context() function can distinguish the two cases by looking at mm->context.asce_limit, for fork() the mm struct has been copied and the number of page table levels may not change. For exec() the mm_alloc() function set the new mm structure to zero, in this case a three-level page table is created as the temporary stack space is located at STACK_TOP_MAX = 4TB. This fixes CVE-2016-2143. Reported-by:
Marcin Kościelnicki <koriakin@0x04.net> Reviewed-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
- 10 Mar, 2016 31 commits
-
-
Parthasarathy Bhuvaragan authored
commit 4de13d7e upstream. commit 4d5cfcba ('tipc: fix connection abort during subscription cancel'), removes the check for a valid subscription before calling tipc_nametbl_subscribe(). This will lead to a nullptr exception when we process a subscription cancel request. For a cancel request, a null subscription is passed to tipc_nametbl_subscribe() resulting in exception. In this commit, we call tipc_nametbl_subscribe() only for a valid subscription. Fixes: 4d5cfcba ('tipc: fix connection abort during subscription cancel') Reported-by:
Anders Widell <anders.widell@ericsson.com> Signed-off-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Parthasarathy Bhuvaragan authored
[ Upstream commit 4d5cfcba ] In 'commit 7fe8097c ("tipc: fix nullpointer bug when subscribing to events")', we terminate the connection if the subscription creation fails. In the same commit, the subscription creation result was based on the value of the subscription pointer (set in the function) instead of the return code. Unfortunately, the same function tipc_subscrp_create() handles subscription cancel request. For a subscription cancellation request, the subscription pointer cannot be set. Thus if a subscriber has several subscriptions and cancels any of them, the connection is terminated. In this commit, we terminate the connection based on the return value of tipc_subscrp_create(). Fixes: commit 7fe8097c ("tipc: fix nullpointer bug when subscribing to events") Reviewed-by:
-
Kamal Mostafa authored
Signed-off-by: -
Willy Tarreau authored
commit 759c0114 upstream. On no-so-small systems, it is possible for a single process to cause an OOM condition by filling large pipes with data that are never read. A typical process filling 4000 pipes with 1 MB of data will use 4 GB of memory. On small systems it may be tricky to set the pipe max size to prevent this from happening. This patch makes it possible to enforce a per-user soft limit above which new pipes will be limited to a single page, effectively limiting them to 4 kB each, as well as a hard limit above which no new pipes may be created for this user. This has the effect of protecting the system against memory abuse without hurting other users, and still allowing pipes to work correctly though with less data at once. The limit are controlled by two new sysctls : pipe-user-pages-soft, and pipe-user-pages-hard. Both may be disabled by setting them to zero. The default soft limit allows the default number of FDs per process (1024) to create pipes of the default size (64kB), thus reaching a limit of 64MB before starting to create only smaller pipes. With 256 processes limited to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB = 1084 MB of memory allocated for a user. The hard limit is disabled by default to avoid breaking existing applications that make intensive use of pipes (eg: for splicing). Reported-by: socketpair@gmail.com Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Mitigates: CVE-2013-4312 (Linux 2.0+) Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Carol L Soto authored
commit bb6a7773 upstream. We are seeing this warning: at net/core/skbuff.c:4174 and before commit a44878d1 ("IB/ipoib: Use one linear skb in RX flow") skb truesize was not being set when ipoib was using just one skb. Removing this line avoids the warning when running tcp tests like iperf. Fixes: a44878d1 ("IB/ipoib: Use one linear skb in RX flow") Signed-off-by:
Carol L Soto <clsoto@linux.vnet.ibm.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Phil Turnbull authored
commit c58d6c93 upstream. If nlh->nlmsg_len is zero then an infinite loop is triggered because 'skb_pull(skb, msglen);' pulls zero bytes. The calculation in nlmsg_len() underflows if 'nlh->nlmsg_len < NLMSG_HDRLEN' which bypasses the length validation and will later trigger an out-of-bound read. If the length validation does fail then the malformed batch message is copied back to userspace. However, we cannot do this because the nlh->nlmsg_len can be invalid. This leads to an out-of-bounds read in netlink_ack: [ 41.455421] ================================================================== [ 41.456431] BUG: KASAN: slab-out-of-bounds in memcpy+0x1d/0x40 at addr ffff880119e79340 [ 41.456431] Read of size 4294967280 by task a.out/987 [ 41.456431] ============================================================================= [ 41.456431] BUG kmalloc-512 (Not tainted): kasan: bad access detected [ 41.456431] ----------------------------------------------------------------------------- ... [ 41.456431] Bytes b4 ffff880119e79310: 00 00 00 00 d5 03 00 00 b0 fb fe ff 00 00 00 00 ................ [ 41.456431] Object ffff880119e79320: 20 00 00 00 10 00 05 00 00 00 00 00 00 00 00 00 ............... [ 41.456431] Object ffff880119e79330: 14 00 0a 00 01 03 fc 40 45 56 11 22 33 10 00 05 .......@EV."3... [ 41.456431] Object ffff880119e79340: f0 ff ff ff 88 99 aa bb 00 14 00 0a 00 06 fe fb ................ ^^ start of batch nlmsg with nlmsg_len=4294967280 ... [ 41.456431] Memory state around the buggy address: [ 41.456431] ffff880119e79400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 41.456431] ffff880119e79480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 41.456431] >ffff880119e79500: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc [ 41.456431] ^ [ 41.456431] ffff880119e79580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 41.456431] ffff880119e79600: fc fc fc fc fc fc fc fc fc fc fb fb fb fb fb fb [ 41.456431] ================================================================== Fix this with better validation of nlh->nlmsg_len and by setting NFNL_BATCH_FAILURE if any batch message fails length validation. CAP_NET_ADMIN is required to trigger the bugs. Fixes: 9ea2aa8b ("netfilter: nfnetlink: validate nfnetlink header from batch") Signed-off-by:
Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Fainelli authored
commit c6dd213a upstream. The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being 10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that. Fixes: d068b02c ("net: phy: add BCM7425 and BCM7429 PHYs") Fixes: 9458ceab ("net: phy: bcm7xxx: Add entry for BCM7435") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
commit d5c3d846 upstream. Commit 2c7b4921 ("phy: fix the use of PHY_IGNORE_INTERRUPT") changed a hunk in phy_state_machine() in the PHY_RUNNING case which was not needed. The change essentially makes the PHY library treat PHY devices with PHY_IGNORE_INTERRUPT to keep polling for the PHY device, even though the intent is not to do it. Fix this by reverting that specific hunk, which makes the PHY state machine wait for state changes, and stay in the PHY_RUNNING state for as long as needed. Fixes: 2c7b4921 ("phy: fix the use of PHY_IGNORE_INTERRUPT") Signed-off-by:
-
Florian Fainelli authored
commit deccd16f upstream. Commit 5ea94e76 ("phy: add phy_mac_interrupt()") to use with PHY_IGNORE_INTERRUPT added a cancel_work_sync() into phy_mac_interrupt() which is allowed to sleep, whereas phy_mac_interrupt() is expected to be callable from interrupt context. Now that we have fixed how the PHY state machine treats PHY_IGNORE_INTERRUPT with respect to state changes, we can just set the new link state, and queue the PHY state machine for execution so it is going to read the new link state. For that to work properly, we need to update phy_change() not to try to invoke any interrupt callbacks if we have configured the PHY device for PHY_IGNORE_INTERRUPT, because that PHY device and its driver are not required to implement those. Fixes: 5ea94e76 ("phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT") Signed-off-by:
-
Heiko Carstens authored
commit 232f5dd7 upstream. git commit dc7ee00d ("s390: lowcore stack pointer offsets") introduced a regression in regard to s390_backtrace(). The stack pointer for the asynchronous stack in the lowcore now has an additional offset applied. This offset needs to be taken into account in the calculation for the low and high address for the stack. This bug was already partially fixed with commit 9cc5c206 ("s390/dumpstack: fix address ranges for asynchronous and panic stack"). This patch fixes it also for the oprofile code. Fixes: dc7ee00d ("s390: lowcore stack pointer offsets") Signed-off-by:
-
Florian Fainelli authored
commit 258bf443 upstream. Since we were wrongly advertising gigabit features for these 10/100 only Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround would have not run since the check would be true, now that we have fixed the PHY features, remove that check since it has no reasoning to be there anymore. Fixes: e18556ee ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR") Signed-off-by:
-
Jay Vosburgh authored
commit 266b495f upstream. There is presently a race condition between the bonding periodic link monitor and the updating of a slave's speed and duplex. The former occurs on a periodic basis, and the latter in response to a driver's calling of netif_carrier_on. It is possible for the periodic monitor to run between the driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE event that causes bonding to update the slave's speed and duplex. This manifests most notably as a report that a slave is up and "0 Mbps full duplex" after enslavement, but in principle could report an incorrect speed and duplex after any link up event if the device comes up with a different speed or duplex. This affects the 802.3ad aggregator selection, as the speed and duplex are selection criteria. This is fixed by updating the speed and duplex in the periodic monitor, prior to using that information. This was done historically in bonding, but the call to bond_update_speed_duplex was removed in commit 876254ae ("bonding: don't call update_speed_duplex() under spinlocks"), as it might sleep under lock. Later, the locking was changed to only hold RTNL, and so after commit 876254ae ("bonding: don't call update_speed_duplex() under spinlocks") this call is again safe. Tested-by:
"Tantilov, Emil S" <emil.s.tantilov@intel.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: dingtianhong <dingtianhong@huawei.com> Fixes: 876254ae ("bonding: don't call update_speed_duplex() under spinlocks") Signed-off-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Acked-by:
Ding Tianhong <dingtianhong@huawei.com> Signed-off-by:
-
Tahsin Erdogan authored
commit 3d65ae46 upstream. inode struct members that track cgroup writeback information should be reinitialized when inode gets allocated from kmem_cache. Otherwise, their values remain and get used by the new inode. Signed-off-by:
Tahsin Erdogan <tahsin@google.com> Acked-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Florian Fainelli authored
commit 50d89980 upstream. The clear and set masks in the call to phy_set_clr_bits() called from bcm7xxx_config_init() are inverted. We need to fix this by swapping the two arguments, that is, set 0 bits, but clear the shade mode 2 enable bit. Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by:
-
Eran Ben Elisha authored
commit 6b94bab0 upstream. The error flow in procedure handle_existing_counter() is wrong. The procedure should exit after encountering the error, not continue as if everything is OK. Fixes: 68230242 ('net/mlx4_core: Add port attribute when tracking counters') Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Rasmus Villemoes authored
commit 76a56367 upstream. Ironically, 7d4020c3 ("[media] exynos4-is: fix some warnings when compiling on arm64") fixed some format string bugs but introduced a new one. buf_index is a simple int, so it should be printed with %d, not %pad (which is correctly used for dma_addr_t). Fixes: 7d4020c3 ("[media] exynos4-is: fix some warnings when compiling on arm64") Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Florian Fainelli authored
commit 87bee0ec upstream. Commit 70371cef ("MAINTAINERS: Add entry for BMIPS multiplatform kernel") supersedes this entry for BCM33xx. Fixes: 70371cef ("MAINTAINERS: Add entry for BMIPS multiplatform kernel") Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Heiko Carstens authored
commit 9900c48c upstream. git commit dc7ee00d ("s390: lowcore stack pointer offsets") introduced a regression in regard to save_stack_trace(). The stack pointer for the asynchronous and the panic stack in the lowcore now have an additional offset applied to them. This offset needs to be taken into account in the calculation for the low and high address for the stacks. This bug was already partially fixed with 9cc5c206 ("s390/dumpstack: fix address ranges for asynchronous and panic stack"). This patch fixes it also for the stacktrace code. Fixes: dc7ee00d ("s390: lowcore stack pointer offsets") Signed-off-by:
Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by:
-
Heinrich Schuchardt authored
commit 9d021c9d upstream. Downstream packages like Debian flash-kernel use /proc/device-tree/model to determine which dtb file to install. Hence each dts in the Linux kernel should provide a unique model identifier. Commit 2d0a7add ("ARM: Kirkwood: Add support for many Synology NAS devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts using the same model identifier. This patch provides a unique model identifier for the Synology DiskStation DS112. Fixes: 2d0a7add ("ARM: Kirkwood: Add support for many Synology NAS devices") Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Arnd Bergmann authored
commit a6ed4a18 upstream. There are two definitions of xpad_identify_controller(), one is used when CONFIG_JOYSTICK_XPAD_LEDS is set, but the other one is empty and never used, and we get a gcc warning about it: drivers/input/joystick/xpad.c:1210:13: warning: 'xpad_identify_controller' defined but not used [-Wunused-function] This removes the second definition. Signed-off-by:
-
Ken-ichirou MATSUZAWA authored
commit aa3a0220 upstream. We should not trim skb for mmaped socket since its buf size is fixed and userspace will read as frame which data equals head. mmaped socket will not call recvmsg, means max_recvmsg_len is 0, skb_reserve was not called before commit: db65a3aa. Fixes: db65a3aa (netlink: Trim skb to alloc size to avoid MSG_TRUNC) Signed-off-by:
Ken-ichirou MATSUZAWA <chamas@h4.dion.ne.jp> Signed-off-by:
-
Rainer Weikusat authored
commit 1b92ee3d upstream. The present unix_stream_read_generic contains various code sequences of the form err = -EDISASTER; if (<test>) goto out; This has the unfortunate side effect of possibly causing the error code to bleed through to the final out: return copied ? : err; and then to be wrongly returned if no data was copied because the caller didn't supply a data buffer, as demonstrated by the program available at http://pad.lv/1540731 Change it such that err is only set if an error condition was detected. Fixes: 3822b5c2 ("af_unix: Revert 'lock_interruptible' in stream receive code") Reported-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by:
-
Andrew Lunn authored
commit 1bc4e2b0 upstream. batman-adv checks in different situation if a new device is already on top of a different batman-adv device. This is done by getting the iflink of a device and all its parent. It assumes that this iflink is always a parent device in an acyclic graph. But this assumption is broken by devices like veth which are actually a pair of two devices linked to each other. The recursive check would therefore get veth0 when calling dev_get_iflink on veth1. And it gets veth0 when calling dev_get_iflink with veth1. Creating a veth pair and loading batman-adv freezes parts of the system ip link add veth0 type veth peer name veth1 modprobe batman-adv An RCU stall will be detected on the system which cannot be fixed. INFO: rcu_sched self-detected stall on CPU 1: (5264 ticks this GP) idle=3e9/140000000000001/0 softirq=144683/144686 fqs=5249 (t=5250 jiffies g=46 c=45 q=43) Task dump for CPU 1: insmod R running task 0 247 245 0x00000008 ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140 0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001 ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001 Call Trace: <IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0 [<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0 [<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180 [<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50 [<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60 [<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90 [<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90 <EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40 [<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv] [<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0 [...] This can be avoided by checking if two devices are each others parent and stopping the check in this situation. Fixes: b7eddd0b ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
-
Heiko Carstens authored
commit 1f8cbb9c upstream. git commit dc7ee00d ("s390: lowcore stack pointer offsets") introduced a regression in regard to perf_callchain_kernel(). The stack pointer for the asynchronous stack in the lowcore now has an additional offset applied. This offset needs to be taken into account in the calculation for the low and high address for the stack. This bug was already partially fixed with 9cc5c206 ("s390/dumpstack: fix address ranges for asynchronous and panic stack"). This patch fixes it also for the perf_event code. Fixes: dc7ee00d ("s390: lowcore stack pointer offsets") Signed-off-by:
-
Daniel Jurgens authored
commit 22e3817e upstream. The PCI channel could go offline during reset due to EEH. Don't bug on in this case, the error is recoverable. Fixes: f6bc11e4 ('net/mlx4_core: Enhance the catas flow to support device reset') Signed-off-by:
Daniel Jurgens <danielj@mellanox.com> Reviewed-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
-
Neil Horman authored
[ Upstream commit d9749fb5 ] Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in its size computation, observing that the current method never guaranteed that the hashsize (measured in number of entries) would be a power of two, which the input hash function for that table requires. The root cause of the problem is that two values need to be computed (one, the allocation order of the storage requries, as passed to __get_free_pages, and two the number of entries for the hash table). Both need to be ^2, but for different reasons, and the existing code is simply computing one order value, and using it as the basis for both, which is wrong (i.e. it assumes that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not). To fix this, we change the logic slightly. We start by computing a goal allocation order (which is limited by the maximum size hash table we want to support. Then we attempt to allocate that size table, decreasing the order until a successful allocation is made. Then, with the resultant successful order we compute the number of buckets that hash table supports, which we then round down to the nearest power of two, giving us the number of entries the table actually supports. I've tested this locally here, using non-debug and spinlock-debug kernels, and the number of entries in the hashtable consistently work out to be powers of two in all cases. Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> CC: Dmitry Vyukov <dvyukov@google.com> CC: Vladislav Yasevich <vyasevich@gmail.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by:
-
Dmitry V. Levin authored
[ Upstream commit b5f05492 ] The value passed by unix_diag_get_exact to unix_lookup_by_ino has type __u32, but unix_lookup_by_ino's argument ino has type int, which is not a problem yet. However, when ino is compared with sock_i_ino return value of type unsigned long, ino is sign extended to signed long, and this results to incorrect comparison on 64-bit architectures for inode numbers greater than INT_MAX. This bug was found by strace test suite. Fixes: 5d3cae8b ("unix_diag: Dumping exact socket core") Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Anton Protopopov authored
[ Upstream commit a97eb33f ] An error response from a RTM_GETNETCONF request can return the positive error value EINVAL in the struct nlmsgerr that can mislead userspace. Signed-off-by:
Anton Protopopov <a.s.protopopov@gmail.com> Acked-by:
-
Xin Long authored
[ Upstream commit deed49df ] Since the gc of ipv4 route was removed, the route cached would has no chance to be removed, and even it has been timeout, it still could be used, cause no code to check it's expires. Fix this issue by checking and removing route cache when we get route. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Guillaume Nault authored
[ Upstream commit 29e73269 ] Drop reference on the relay_po socket when __pppoe_xmit() succeeds. This is already handled correctly in the error path. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Mark Tomlinson authored
[ Upstream commit 853effc5 ] A previous commit (33f72e6f) added notification via netlink for tunnels when created/modified/deleted. If the notification returned an error, this error was returned from the tunnel function. If there were no listeners, the error code ESRCH was returned, even though having no listeners is not an error. Other calls to this and other similar notification functions either ignore the error code, or filter ESRCH. This patch checks for ESRCH and does not flag this as an error. Reviewed-by:
Hamish Martin <hamish.martin@alliedtelesis.co.nz> Signed-off-by:
Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by:
-
