* pci/vpd:
  PCI: Increase VPD access timeout to 125ms

* pci/virtualization:
  PCI: Lock each enable/disable num_vfs operation in sysfs
  PCI: Add ACS quirk for Intel Union Point

* pci/resource:
  PCI: Remove res_to_dev_res() debug message

* pci/msi:
  PCI/MSI: Update MSI/MSI-X bits in PCIEBUS-HOWTO
  PCI/MSI: Document pci_alloc_irq_vectors(), deprecate pci_enable_msi()
  PCI/MSI: Return -ENOSPC if pci_enable_msi_range() can't get enough vectors
  PCI/portdrv: Use pci_irq_alloc_vectors()
  PCI/MSI: Check that we have a legacy interrupt line before using it
  PCI/MSI: Remove pci_msi_domain_{alloc,free}_irqs()
  PCI/MSI: Remove unused pci_msi_create_default_irq_domain()
  PCI/MSI: Return failure when msix_setup_entries() fails
  PCI/MSI: Remove pci_enable_msi_{exact,range}()
  amd-xgbe: Update PCI support to use new IRQ functions
  [media] cobalt: use pci_irq_allocate_vectors()
  PCI/MSI: Fix msi_capability_init() kernel-doc warnings

* pci/hotplug:
  PCI: acpiphp_ibm: Make ibm_apci_table_attr __ro_after_init
  PCI: rpadlpar: Remove unnecessary return statement

* pci/enumeration:
  PCI: Remove duplicate check for positive return value from probe() functions
  PCI: Enable PCIe Extended Tags if supported
  PCI: Avoid possible deadlock on pci_lock and p->pi_lock
  PCI/ACPI: Fix bus range comparison in pci_mcfg_lookup()
  PCI: Apply _HPX settings only to relevant devices

* pci/dpc:
  PCI/DPC: Wait for Root Port busy to clear
  PCI/DPC: Decode extended reasons

* pci/aspm:
  PCI/ASPM: Add comment about L1 substate latency
  PCI/ASPM: Configure L1 substate settings
  PCI/ASPM: Calculate and save the L1.2 timing parameters
  PCI/ASPM: Read and set up L1 substate capabilities
  PCI/ASPM: Add support for L1 substates
  PCI/ASPM: Add L1 substate capability structure register definitions

* pci/aer:
  PCI/AER: Remove unused .link_reset() callback

Update the MSI/MSI-X bits in PCIEBUS-HOWTO.  Stop talking about low-level
details that mention deprecated APIs and concentrate on what service
drivers should do and why.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Document pci_alloc_irq_vectors() instead of the deprecated pci_enable_msi()
and pci_enable_msix() APIs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Since the exit latencies for L1 substates are not advertised by a device,
it is not clear in spec how to do a L1 substate exit latency check.  We
assume that the L1 exit latencies advertised by a device include L1
substate latencies (and hence do not do any check).  If that is not true,
we should do some sort of check here.

(I'm not clear about what that check should like currently. I'd be glad to
take up any suggestions).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Configure the L1 substate settings on the upstream and downstream devices,
while taking care of the rules dictated by the PCIe spec.

[bhelgaas: drop "inline"]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Calculate and save the timing parameters that need to be programmed if we
need to enable L1.2 substates later.

We use the same logic (and a constant value for 1 of the parameters) as
used by Intel's coreboot:

  https://www.coreboot.org/pipermail/coreboot-gerrit/2015-March/021134.html
  https://review.coreboot.org/#/c/8832/Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The PCIe spec (r3.1, sec 7.33) says the L1 PM Substates Capability may be
implemented only in function 0.

Read the L1 substate capability structures of upstream and downstream
components of the link and set it up in the device structure.

[bhelgaas: add specific spec reference]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add support for ASPM L1 substates.  For details about L1 substates, see the
PCIe r3.1 spec, which includes the ECN below in secs 5.5 and 7.33.

Add macros for the 4 new L1 substates, and add a new ASPM "POWER_SUPERSAVE"
policy that can be used to enable L1 substates on a system if desired.  The
new policy is in a sense, a superset of the existing POWERSAVE policy.  The
4 policies are now:

  DEFAULT: Reads and uses whatever ASPM states BIOS enabled
  PERFORMANCE: Everything except L0 disabled.
  POWERSAVE: L0s and L1 enabled (but not L1 substates)
  POWER_SUPERSAVE: L0s + L1 + L1 substates also enabled

[bhelgaas: add PCIe r3.1 spec reference]
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_L1_PM_Substates_with_CLKREQ_31_May_2013_Rev10a.pdfSigned-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add L1 substate capability structure register definitions for use in
subsequent patches.  See the PCIe r3.1 spec, sec 7.33.

[bhelgaas: add PCIe spec reference]
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

If device doesn't support as many MSI vectors as the driver requested, we
previously returned -EINVAL from __pci_enable_msi_range() and
pci_enable_msi_range().  In other similar situations in both
__pci_enable_msi_range() and __pci_enable_msix_range(), we returned
-ENOSPC.

Return -ENOSPC from __pci_enable_msi_range() so we do it consistently.

[bhelgaas: changelog]
Signed-off-by: Dennis Chen <dennis.chen@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tejun Heo <tj@kernel.org>
CC: Christoph Hellwig <hch@lst.de>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: Steve Capper <steve.capper@arm.com>

Use pci_irq_alloc_vectors() and greatly simplify the code by managing the
vector number for the subservices directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

It seems like there are some devices (e.g. the PCIe root port driver) that
may not always have a INTx interrupt.  Check for dev->irq before returning
a legacy interrupt in pci_irq_alloc_vectors to properly handle this case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Function __pci_device_probe() tries to be careful about a PCI driver
probe() hook returning a positive value, but this is not really necessary,
since the same fix up is already done in local_pci_probe() (preceded by a
noisy warning), which renders this instance dead code.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Per PCIe r3.1, sec 6.2.10 and sec 7.13.4, on Root Ports that support "RP
Extensions for DPC",

  When the DPC Trigger Status bit is Set and the DPC RP Busy bit is Set,
  software must leave the Root Port in DPC until the DPC RP Busy bit reads
  0b.

Wait up to 1 second for the Root Port to become non-busy.

[bhelgaas: changelog, spec references]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Decode the currently defined extended event reasons rather than just using
the generic "extended" explanation.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Just call the msi_* version directly instead of having trivial wrappers for
one or two callsites.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>

pci_msi_create_default_irq_domain() is never called in the whole tree, so
remove it as well as all the supporting code for a default PCI MSI domain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>

If alloc_msi_entry() fails, we free resources and set ret = -ENOMEM.

However, msix_setup_entries() returns 0 unconditionally.  Return the error
code instead.

Fixes: e75eafb9 ("genirq/msi: Switch to new irq spreading infrastructure")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Every PCIe device can generate 5-bit transaction Tags, which allow up to 32
concurrent requests.  Some devices can generate 8-bit Extended Tags, which
allow up to 256 concurrent requests.

Per the ECN mentioned below, all PCIe Receivers are expected to support
Extended Tags, so devices are allowed (but not required) to enable them by
default.

If a device supports Extended Tags but does not enable them by default,
enable them.  This allows the device to have up to 256 outstanding
transactions at a time, which may improve performance.

[bhelgaas: changelog, check for PCIe device]
Link: https://pcisig.com/sites/default/files/specification_documents/ECN_Extended_Tag_Enable_Default_05Sept2008_final.pdfSigned-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

No hardware seems to actually call .link_reset(), and no driver implements
it as more than a nop stub.

Drop mentions of the callback from everywhere.  It's dropped from the
documentation as well, but the doc really needs to be updated to reflect
reality better (e.g., on PCIe, slot reset is the link reset).  This will be
done in a later patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Enabling/disabling SRIOV via sysfs by echo-ing multiple values
simultaneously:

  # echo 63 > /sys/class/net/ethX/device/sriov_numvfs&
  # echo 63 > /sys/class/net/ethX/device/sriov_numvfs

  # sleep 5

  # echo 0 > /sys/class/net/ethX/device/sriov_numvfs&
  # echo 0 > /sys/class/net/ethX/device/sriov_numvfs

results in the following bug:

  kernel BUG at drivers/pci/iov.c:495!
  invalid opcode: 0000 [#1] SMP
  CPU: 1 PID: 8050 Comm: bash Tainted: G   W   4.9.0-rc7-net-next #2092
  RIP: 0010:[<ffffffff813b1647>]
	    [<ffffffff813b1647>] pci_iov_release+0x57/0x60

  Call Trace:
   [<ffffffff81391726>] pci_release_dev+0x26/0x70
   [<ffffffff8155be6e>] device_release+0x3e/0xb0
   [<ffffffff81365ee7>] kobject_cleanup+0x67/0x180
   [<ffffffff81365d9d>] kobject_put+0x2d/0x60
   [<ffffffff8155bc27>] put_device+0x17/0x20
   [<ffffffff8139c08a>] pci_dev_put+0x1a/0x20
   [<ffffffff8139cb6b>] pci_get_dev_by_id+0x5b/0x90
   [<ffffffff8139cca5>] pci_get_subsys+0x35/0x40
   [<ffffffff8139ccc8>] pci_get_device+0x18/0x20
   [<ffffffff8139ccfb>] pci_get_domain_bus_and_slot+0x2b/0x60
   [<ffffffff813b09e7>] pci_iov_remove_virtfn+0x57/0x180
   [<ffffffff813b0b95>] pci_disable_sriov+0x65/0x140
   [<ffffffffa00a1af7>] ixgbe_disable_sriov+0xc7/0x1d0 [ixgbe]
   [<ffffffffa00a1e9d>] ixgbe_pci_sriov_configure+0x3d/0x170 [ixgbe]
   [<ffffffff8139d28c>] sriov_numvfs_store+0xdc/0x130
  ...
  RIP  [<ffffffff813b1647>] pci_iov_release+0x57/0x60

Use the existing mutex lock to protect each enable/disable operation.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>

The PCI core uses a fixed 50ms timeout when waiting for VPD accesses to
complete.  When an access does not complete within this period, a warning
is logged and an error returned to the caller.

While this default timeout is valid for most hardware, some devices can
experience longer access delays under certain circumstances.  For example,
one of the IBM CXL Flash devices can take up to ~120ms in a worst-case
scenario.  These types of devices can benefit from an extended timeout.

To support devices with a longer access delay, increase the timeout in
pci_vpd_wait() to 125ms.  The PCI specification is silent with respect to
VPD delays, therefore there is no concern for violating a threshold.
Tested-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>

pci_lock is an IRQ-safe spinlock that protects all accesses to PCI
configuration space (see PCI_OP_READ() and PCI_OP_WRITE() in pci/access.c).

The pci_cfg_access_unlock() path acquires pci_lock, then p->pi_lock (inside
wake_up_all()).  According to lockdep, there is a possible path involving
snbep_uncore_pci_read_counter() that could acquire them in the reverse
order: acquiring p->pi_lock, then pci_lock, which could result in a
deadlock.  Lockdep details are in the bugzilla below.

Avoid the possible deadlock by dropping pci_lock before waking up any
config access waiters.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=192901Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words.  Add PCIe root port device IDs to
existing quirk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

All multi-MSI allocations are now done through pci_irq_alloc_vectors(), so
remove the old pci_enable_msi_range() and pci_enable_msi_exact()
interfaces.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Some of the PCI MSI/MSI-X functions have been deprecated and it is
recommended to use the new pci_alloc_irq_vectors() function. Convert the
code over to use the new function. Also, modify the way in which the IRQs
are requested - try for multiple MSI-X/MSI first, then a single MSI/legacy
interrupt.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Simplify the interrupt setup by using the new PCI layer helpers.

Despite using pci_enable_msi_range(), this driver was only requesting a
single MSI vector anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The configuration data provided by an MCFG entry, i.e., PCI segment and bus
range, may span multiple host bridges.

pci_mcfg_lookup() previously required an exact match of the host bridge
starting bus and the MCFG starting bus, which made the following
configuration fail:

  MCFG region:
    segment: 0
    bus range: 0x00-0xff

  host bridge
    segment: 0
    bus range: 0x20-0x4f

Relax the bus range check in pci_mcfg_lookup() so we can use any MCFG entry
that contains the required bus range, as we do in pci_mmconfig_lookup().

[bhelgaas: changelog]
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Fix kernel-doc warnings in pci/msi.c:

  ..//drivers/pci/msi.c:623: warning: No description found for parameter 'affd'
  ..//drivers/pci/msi.c:623: warning: Excess function parameter 'affinity' description in 'msi_capability_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

ibm_apci_table_attr is not modified after being initialized by
ibm_acpiphp_init().  It is passed as an argument to the functions
sysfs_{remove/create}_bin_file(), but both the arguments are const.
Add __ro_after_init to its declaration.

[bhelgaas: changelog]
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>

Remove unnecessary return statement using spatch tool.
Signed-off-by: Rahul Krishnan <mrahul.krishnan@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>

Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.

We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.

We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings.  I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm.  But it's
ugly to depend on those internals.

Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).

A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:

  pci 0000:00:00.0: PCI-X settings not supported

After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=187731Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>