- 19 Oct, 2021 13 commits
-
-
Mirela Rabulea authored
Save some power by disabling/enabling the jpeg clocks with every stream stop/start. Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains, to ensure power domains are off after probe. Signed-off-by:
Mirela Rabulea <mirela.rabulea@oss.nxp.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Jeff Chase authored
Jeff is leaving Google so Joe will take over. Signed-off-by:
Jeff Chase <jnchase@google.com> Signed-off-by:
-
Krzysztof Hałasa authored
Confirmed to work with ADV7610 HDMI receiver. Signed-off-by:
Krzysztof Hałasa <khalasa@piap.pl> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Krzysztof Hałasa authored
ADV7610 is another HDMI receiver chip, very similar to the ADV7611. Also: print chip names in upper case. Fix an error message claiming that no ADV761x has been found, while in reality a chip different than requested (though still supported) may have been found. Tested on TinyRex BaseBoard Lite. Signed-off-by:
-
Krzysztof Hałasa authored
ADV7610 is another HDMI receiver chip, very similar to the ADV7611. Tested on TinyRex BaseBoard Lite. Signed-off-by:
-
Krzysztof Hałasa authored
The TDA1997x (HDMI receiver) driver currently uses a specific video format detection scheme. The frame (or field in interlaced mode), line and HSync pulse durations are compared to those of known, standard video modes. If a match is found, the mode is assumed to be detected, otherwise -ERANGE is returned (then possibly ignored). This means that: - another mode with similar timings will be detected incorrectly (e.g. 2x faster clock and lines twice as long) - non-standard modes will not work. This patch replaces this scheme with a direct read of geometry registers. This way all modes recognized by the chip are supported. In interlaced modes, the code assumes the V sync signal has the same duration for both fields. While this may be not necessarily true, I can't see any way to get the "other" V sync width. This is most probably harmless. All tests have been performed on Gateworks' Ventana GW54xx board, with a TDA19971 chip. Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
-
Hans Verkuil authored
Newer clang versions are suspicious of definitions that mix concatenated strings with comma-separated arrays of strings, this has found real bugs elsewhere, but this seems to be a false positive: drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:37: error: suspicious concatenation of string literals in an array initialization; did you mean to separate the elements with a comma? [-Werror,-Wstring-concatenation] "\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1" ^ , drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:2: note: place parentheses around the string literal to silence warning "\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1" Replace the string literals by compound initializers, using normal hex numbers. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Reviewed-by:
-
Scott K Logan authored
Similar configuration to Kworld PC150-U. Tested: Composite, S-Video, NTSC, ATSC Unsupported: IR remote Signed-off-by:
Scott K Logan <logans@cottsay.net> Signed-off-by:
-
Jammy Huang authored
To show video real-time information as below: Capture: Signal : Unlock Width : 1920 Height : 1080 FRC : 30 Performance: Frame# : 0 Frame Duration(ms) : Now : 0 Min : 0 Max : 0 FPS : 0 [hverkuil: make aspeed_video_proc_open() static, fixes sparse warning] Signed-off-by:Jammy Huang <jammy_huang@aspeedtech.com> Signed-off-by:
-
Sergey Senozhatsky authored
We need to always link allocated vb2_dc_buf back to vb2_buffer because we dereference vb2 in prepare() and finish() callbacks. Signed-off-by:
Sergey Senozhatsky <senozhatsky@chromium.org> Tested-by:
Chen-Yu Tsai <wenst@chromium.org> Acked-by:
Tomasz Figa <tfiga@chromium.org> Signed-off-by:
-
Vladimir Barinov authored
This adds g/s_parm ioctls for parallel interface. Signed-off-by:
Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
-
Arnd Bergmann authored
I came across a link failure from randconfig builds: x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove': ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev' x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe': ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev' x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove': tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev' x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe': tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev' These clearly lack a 'select' statement, but I don't know why this started happening only now. I had a bit of a look around to find other configs that have the same problem, but could not come up with a reliable way and found nothing else through experimentation. It is likely that other symbols like these exist that need an extra select. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Hans Verkuil authored
Adding kfree(dvb) to vidtv_bridge_remove() will remove the memory too soon: if an application still has an open filehandle to the device when the driver is unloaded, then when that filehandle is closed, a use-after-free access takes place to the freed memory. Move the kfree(dvb) to vidtv_bridge_dev_release() instead. Signed-off-by:
-
- 18 Oct, 2021 1 commit
-
-
Daniel Almeida authored
If v4l2_ctrl_new_custom fails in cedrus_init_ctrls the error path will free ctx->ctrls, which is also freed in cedrus release. Fix this by setting ctx->ctrls to NULL instead of inadvertently removing kfree calls. Signed-off-by:
Daniel Almeida <daniel.almeida@collabora.com> Signed-off-by:
-
- 08 Oct, 2021 26 commits
-
-
Sean Young authored
I have not been able to give dvb the attention it needs, and now I have even less time. Of course I will continue to maintain rc-core (infrared). Unfortunately this means that dvb will have maintainance issues. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Anant Thazhemadam authored
In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets assigned an value that's not properly initialized. Using kzalloc() in place of kmalloc() for the buffer fixes this issue, as the val can now be set to 0 in the event dibusb_i2c_msg() fails. Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Signed-off-by:
Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by:
-
Nil Yi authored
After freed the dev->urb_list, we should set it to NULL as well as set counter to zero. Requested-by:
Nil Yi <teroincn@163.com> Signed-off-by:
-
Evgeny Novikov authored
mn88443x_cmn_power_on() did not handle possible errors of clk_prepare_enable() and always finished successfully so that its caller mn88443x_probe() did not care about failed preparing/enabling of clocks as well. Add missed error handling in both mn88443x_cmn_power_on() and mn88443x_probe(). This required to change the return value of the former from "void" to "int". Found by Linux Driver Verification project (linuxtesting.org). Fixes: 0f408ce8 ("media: dvb-frontends: add Socionext MN88443x ISDB-S/T demodulator driver") Signed-off-by:
Evgeny Novikov <novikov@ispras.ru> Co-developed-by:
Kirill Shilimanov <kirill.shilimanov@huawei.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only arrays on the stack but instead them static const. Also makes the object code smaller by 154 bytes: Before: text data bss dec hex filename 42949 22424 0 65373 ff5d media/dvb-frontends/mb86a20s.o After: text data bss dec hex filename 42731 22488 0 65219 fec3 media/dvb-frontends/mb86a20s.o (gcc version 11.2.0) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Ricardo Ribalda authored
Use v4l2 control API helpers to support the events. Fixes v4l2-compliance: test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL Signed-off-by:
Ricardo Ribalda <ribalda@chromium.org> Signed-off-by:
-
Ricardo Ribalda authored
Use v4l2 control API helpers to support the events. Fixes v4l2-compliance: test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL Signed-off-by:
-
Ricardo Ribalda authored
Use v4l2 control API helpers to support the events. Fixes v4l2-compliance: test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL Signed-off-by:
-
Ricardo Ribalda authored
bus_info field had a different value for the media entity and the video device. Fixes v4l2-compliance: v4l2-compliance.cpp(637): media bus_info 'PCI:0000:00:05.0' differs from V4L2 bus_info 'PCI:viewfinder' Reviewed-by:
Bingbu Cao <bingbu.cao@intel.com> Signed-off-by:
-
Ricardo Ribalda authored
For a try_fmt call, the node noes not need to be enabled. Fixes v4l2-compliance fail: v4l2-test-formats.cpp(717): Video Output Multiplanar is valid, but no TRY_FMT was implemented test VIDIOC_TRY_FMT: FAIL Signed-off-by:
-
Ricardo Ribalda authored
The initial format did not have a valid size. Fixes v4l2-compliance: fail: v4l2-test-formats.cpp(723): Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT test VIDIOC_TRY_FMT: FAIL Signed-off-by:
-
Ricardo Ribalda authored
Move the calculation to an inline function, to it can be used by other parts of the driver. Signed-off-by:
-
Ricardo Ribalda authored
If num_planes is different than zero num_planes and sizes must be checked to support the format. Fix the following v4l2-compliance error: Buffer ioctls (Input 0): fail: v4l2-test-buffers.cpp(717): q.create_bufs(node, 1, &fmt) != EINVAL test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL Reviewed-by: -
Niklas Söderlund authored
Add a V4L2 driver for Renesas R-Car Image Signal Processor. The driver supports the R-Car V3U SoC where the ISP IP sits between the R-Car CSI-2 receiver and VIN and filters the CSI-2 data based on VC/DT and directs the video stream to different VIN IPs. Signed-off-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Rikard Falkeborn authored
The only usage of imgu_subdev_internal_ops is to assign its address to the internal_ops field in the v4l2_subdev struct, which is a pointer to const v4l2_subdev_internal_ops. Make it const to allow the compiler to put it in read-only memory. Signed-off-by:
Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by:
-
Sakari Ailus authored
Add MIPI CCS compliant devices, a few Sony IMX, Hynix Hi-846 and Omnivision ov13b10 sensors and the DW9768 lens driver to the list of supported devices. Also drop SMIA since as a standard it is obsolete. Signed-off-by:
-
Martin Kepplinger authored
Add the SK Hynix Hi-846 8M Pixel CMOS image sensor to the i2c-cardlist. Signed-off-by:
Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by:
-
Martin Kepplinger authored
The SK Hynix Hi-846 is a 1/4" 8M Pixel CMOS Image Sensor. It supports usual features like I2C control, CSI-2 for frame data, digital/analog gain control or test patterns. This driver supports the 640x480, 1280x720 and 1632x1224 resolution modes. It supports runtime PM in order not to draw any unnecessary power. The part is also called YACG4D0C9SHC and a datasheet can be found at https://product.skhynix.com/products/cis/cis.go The large sets of partly undocumented register values are for example found when searching for the hi846_mipi_raw_Sensor.c Android driver. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Martin Kepplinger authored
Document the bindings used for the SK Hynix Hi-846 CMOS camera driver. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Martin Kepplinger authored
SK Hynix built the already supported hi556 sensor (and probably much more). For more information, see https://www.skhynix.com/Signed-off-by:
-
Fabian Wüthrich authored
The sensor orientation is read from the _PLC ACPI buffer and converted to a v4l2 format. The sensor rotation is read from the SSDB ACPI buffer and converted into degrees. Signed-off-by:
Fabian Wüthrich <me@fabwu.ch> Reviewed-by:
Daniel Scally <djrscally@gmail.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
Dikshita Agarwal authored
- Get the min buffer count required by FW from source event change and use the same value to decide actual buffer count and for buffer size calculation. - Setup DPB and OPB buffers after session continue incase of reconfig. Signed-off-by:
Dikshita Agarwal <dikshita@codeaurora.org> Signed-off-by:
Stanimir Varbanov <stanimir.varbanov@linaro.org> Signed-off-by:
-
Dikshita Agarwal authored
Consider alignment while calculating NUM_MBS. Co-developed-by:
Mansur Alisha Shaik <mansur@codeaurora.org> Signed-off-by:
-
Dikshita Agarwal authored
Set work route to FW based on num of vpp pipes. Signed-off-by:
-
Dikshita Agarwal authored
AON register programming is used to set NOC to low power mode during V6 power off sequence. However AON register memory map is not applicable to 1pipe, hence skipping AON register programming. Co-developed-by:
Vikash Garodia <vgarodia@codeaurora.org> Signed-off-by:
-
Dikshita Agarwal authored
V6 HW can have vpp pipes as 1 or 4, add num_vpp_pipes to resource struture to differentiate. Signed-off-by:
-
