There are no separate serial/SPI devices under the at91-usart MFD, but
actually the MFD is used as a serial or a SPI device. There are no DT
sub-nodes for the MFD children, so we should use platform device API to
register the drivers.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use regmap accessors directly for register manipulation - removing one
layer of abstraction.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

An errata exists for cs47l15 where the reset must be handled
differently and removed before DCVDD is applied. A soft reset is used
for situations where a reset is required to reset state. This does
however, make this part unsuitable for DCVDD supplies with a rise time
greater than 2mS.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The DCVDD supply does not always power down when the CODEC enters
suspend, for example shared regulators or always-on regulators. In
these cases if a register is written back to the default value whilst
the CODEC is in suspend that register will retain the previous value.
As DCVDD never powered down, the register retains its old value and
as the cache sync only synchronises registers that differ from the
default the new value is never written out.

Ensure the registers are in the expected state after suspend by always
resetting the CODEC on resume. This also has the benefit of being
recommended by the datasheet for DCVDD supplies that take longer than
2mS to rise.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add common properties appearing in DTSes (clock-names,
clock-output-names) with the common values (actually used in DTSes) to
fix dtbs_check warnings like:

  arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dt.yaml:
    pmic@4b: 'clock-names', 'clock-output-names', do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

 CHECK: Alignment should match open parenthesis
 #24: FILE: drivers/mfd/tps65910.c:296:
 +	ret = regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
  						DEVCTRL_CK32K_CTRL_MASK);

 CHECK: Alignment should match open parenthesis
 #33: FILE: drivers/mfd/tps65910.c:318:
 +	ret = regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
  				DEVCTRL_DEV_SLP_MASK);

 CHECK: Alignment should match open parenthesis
 #42: FILE: drivers/mfd/tps65910.c:326:
 +		ret = regmap_set_bits(tps65910->regmap,
  				TPS65910_SLEEP_KEEP_RES_ON,

 CHECK: Alignment should match open parenthesis
 #51: FILE: drivers/mfd/tps65910.c:336:
 +		ret = regmap_set_bits(tps65910->regmap,
  				TPS65910_SLEEP_KEEP_RES_ON,

 CHECK: Alignment should match open parenthesis
 #60: FILE: drivers/mfd/tps65910.c:346:
 +		ret = regmap_set_bits(tps65910->regmap,
  				TPS65910_SLEEP_KEEP_RES_ON,

 CHECK: Alignment should match open parenthesis
 #69: FILE: drivers/mfd/tps65910.c:358:
 +	regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
  				DEVCTRL_DEV_SLP_MASK);

 CHECK: Alignment should match open parenthesis
 #78: FILE: drivers/mfd/tps65910.c:440:
 +	if (regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
  			DEVCTRL_PWR_OFF_MASK) < 0)

 CHECK: Alignment should match open parenthesis
 #83: FILE: drivers/mfd/tps65910.c:444:
 +	regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
  			DEVCTRL_DEV_ON_MASK);
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Client pointers in tps65910 data are not used in the drivers.
Remove those fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove wrappers around regmap calls to remove now-useless indirection.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use regmap accessors directly for register manipulation - removing
one layer of abstraction.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the subtype and compatible strings for PM660 and PM660L,
found in various SoCs, including SDM630, SDM636, SDM660 and
SDA variants.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The register field xxx_WIDTH defines are not used in current code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify adc_resources[]. The only usage is to assign its address to the
resources field of the mfd_cell struct. This allows the compiler to put
it in read-only memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This adds syscon_regmap_lookup_by_phandle_optional() function to get an
optional regmap.

It behaves the same as syscon_regmap_lookup_by_phandle() except where
there is no regmap phandle. In this case, instead of returning -ENODEV,
the function returns NULL. This makes error checking simpler when the
regmap phandle is optional.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the Intel Platform Monitoring Technology crashlog
interface. This interface provides a few sysfs values to allow for
controlling the crashlog telemetry interface as well as a character
driver to allow for mapping the crashlog memory region so that it can be
accessed after a crashlog has been recorded.

This driver is meant to only support the server version of the crashlog
which is identified as crash_type 1 with a version of zero. Currently no
other types are supported.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

PMT Telemetry is a capability of the Intel Platform Monitoring Technology.
The Telemetry capability provides access to device telemetry metrics that
provide hardware performance data to users from read-only register spaces.

With this driver present the intel_pmt directory can be populated with
telem<x> devices. These devices will contain the standard intel_pmt sysfs
data and a "telem" binary sysfs attribute which can be used to access the
telemetry data.

Also create a PCI device id list for early telemetry hardware that require
workarounds for known issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Co-developed-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Intel Platform Monitoring Technology is meant to provide a common way to
access telemetry and system metrics.

Register mappings are not provided by the driver. Instead, a GUID is read
from a header for each endpoint. The GUID identifies the device and is to
be used with an XML, provided by the vendor, to discover the available set
of metrics and their register mapping.  This allows firmware updates to
modify the register space without needing to update the driver every time
with new mappings. Firmware writes a new GUID in this case to specify the
new mapping.  Software tools with access to the associated XML file can
then interpret the changes.

The module manages access to all Intel PMT endpoints on a system,
independent of the device exporting them. It creates an intel_pmt class
to manage the devices. For each telemetry endpoint, sysfs files provide
GUID and size information as well as a pointer to the parent device the
telemetry came from. Software may discover the association between
endpoints and devices by iterating through the list in sysfs, or by looking
for the existence of the class folder under the device of interest.  A
binary sysfs attribute of the same name allows software to then read or map
the telemetry space for direct access.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Intel Platform Monitoring Technology (PMT) is an architecture for
enumerating and accessing hardware monitoring facilities. PMT supports
multiple types of monitoring capabilities. This driver creates platform
devices for each type so that they may be managed by capability specific
drivers (to be introduced). Capabilities are discovered using PCIe DVSEC
ids. Support is included for the 3 current capability types, Telemetry,
Watcher, and Crashlog. The features are available on new Intel platforms
starting from Tiger Lake for which support is added. This patch adds
support for Tiger Lake (TGL), Alder Lake (ADL), and Out-of-Band Management
Services Module (OOBMSM).

Also add a quirk mechanism for several early hardware differences and bugs.
For Tiger Lake and Alder Lake, do not support Watcher and Crashlog
capabilities since they will not be compatible with future product. Also,
fix use a quirk to fix the discovery table offset.
Co-developed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add PCIe Designated Vendor-Specific Extended Capability (DVSEC) and defines
for the header offsets. Defined in PCIe r5.0, sec 7.9.6.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset

Pull scheduler fixes from Thomas Gleixner:
 "Two scheduler fixes:

   - A trivial build fix for sched_feat() to compile correctly with
     CONFIG_JUMP_LABEL=n

   - Replace a zero lenght array with a flexible array"

* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/features: Fix !CONFIG_JUMP_LABEL case
  sched: Replace zero-length array with flexible-array

Pull perf fix from Thomas Gleixner:
 "A single fix to compute the field offset of the SNOOPX bit in the data
  source bitmask of perf events correctly"

* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: correct SNOOPX field offset

Pull locking fix from Thomas Gleixner:
 "Just a trivial fix for kernel-doc warnings"

* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/seqlocks: Fix kernel-doc warnings

Pull NTB fixes from Jon Mason.

* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
  NTB: Use struct_size() helper in devm_kzalloc()
  ntb: intel: Fix memleak in intel_ntb_pci_probe
  NTB: hw: amd: fix an issue about leak system resources

Pull i2c fix from Wolfram Sang:
 "Regression fix for rc1 and stable kernels as well"

* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs

Pull more cifs updates from Steve French:
 "Add support for stat of various special file types (WSL reparse points
  for char, block, fifo)"

* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  smb3: add some missing definitions from MS-FSCC
  smb3: remove two unused variables
  smb3: add support for stat of WSL reparse points for special file types

Pull more parisc updates from Helge Deller:

 - During this merge window O_NONBLOCK was changed to become 000200000,
   but we missed that the syscalls timerfd_create(), signalfd4(),
   eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
   bit-wise check of the flags parameter.

   To provide backward compatibility with existing userspace we
   introduce parisc specific wrappers for those syscalls which filter
   out the old O_NONBLOCK value and replaces it with the new one.

 - Prevent HIL bus driver to get stuck when keyboard or mouse isn't
   attached

 - Improve error return codes when setting rtc time

 - Minor documentation fix in pata_ns87415.c

* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  ata: pata_ns87415.c: Document support on parisc with superio chip
  parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
  hil/parisc: Disable HIL driver when it gets stuck
  parisc: Improve error return codes when setting rtc time

Pull more xen updates from Juergen Gross:

 - a series for the Xen pv block drivers adding module parameters for
   better control of resource usge

 - a cleanup series for the Xen event driver

* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  Documentation: add xen.fifo_events kernel parameter description
  xen/events: unmask a fifo event channel only if it was masked
  xen/events: only register debug interrupt for 2-level events
  xen/events: make struct irq_info private to events_base.c
  xen: remove no longer used functions
  xen-blkfront: Apply changed parameter name to the document
  xen-blkfront: add a parameter for disabling of persistent grants
  xen-blkback: add a parameter for disabling of persistent grants