When the device is configured to use single chip addressing mode, the
phy devices of the port are not accessible on the host MDIO
bus. Instead the switch internal MDIO bus must be used. For this to
work, the phy polling unit must be enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This debug output is not really an error message since mac reset can fail
if the phy clocks are gated, specifically when the phy has been placed in
a powered down or isolation mode. The netdev output masks were changed from
err to dbg, and comments added in the code.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change use of Altera TSE's MDIO access from phy 0 registers to phy 1
registers. This allows support for GMII, MII, RGMII, and SGMII
designs where the external PHY is always accesible through
Altera TSE's MDIO phy 1 registers and Altera's PCS is accessible
through MDIO phy 0 registers for SGMII applications.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Tested-by: Kai Lin Ng <kailng@altera.com>
Tested-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
Adjust the settings about USB_RX_EARLY_AGG

v2:
For patch #1, replace

	u32 ocp_data;
	ocp_data = tp->coalesce / 8;

with

	u32 ocp_data = tp->coalesce / 8;

And replace

	struct net_device *dev = tp->netdev;
	u32 ocp_data;
	ocp_data = (agg_buf_sz - dev->mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;

with

	u32 mtu = tp->netdev->mtu;
	u32 ocp_data = (agg_buf_sz - mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;

Use *switch* statement to replace the checking of *if*.

v1:
The USB_RX_EARLY_AGG contains timeout and size. Separate them, and
they could be set independently. Then, the ethtool could be used to
change the timeout according to situation of the platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.

Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().

Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking updates from David Miller:

 1) Missing netlink attribute validation in nft_lookup, from Patrick
    McHardy.

 2) Restrict ipv6 partial checksum handling to UDP, since that's the
    only case it works for.  From Vlad Yasevich.

 3) Clear out silly device table sentinal macros used by SSB and BCMA
    drivers.  From Joe Perches.

 4) Make sure the remote checksum code never creates a situation where
    the remote checksum is applied yet the tunneling metadata describing
    the remote checksum transformation is still present.  Otherwise an
    external entity might see this and apply the checksum again.  From
    Tom Herbert.

 5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.

 6) Don't explicitly initialize timer struct fields, use setup_timer()
    and mod_timer() instead.  From Vaishali Thakkar.

 7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
    Nomura.

 8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.

 9) Don't potentially perform skb_get() on shared skbs, also from Eric
    Dumazet.

10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
    KaFai Lau.

11) Fix merge resolution error between the iov_iter changes in vhost and
    some bug fixes that occurred at the same time.  From Jason Wang.

12) If rtnl_configure_link() fails we have to perform a call to
    ->dellink() before unregistering the device.  From WANG Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
  net: dsa: Set valid phy interface type
  rtnetlink: call ->dellink on failure when ->newlink exists
  com20020-pci: add support for eae single card
  vhost_net: fix wrong iter offset when setting number of buffers
  net: spelling fixes
  net/core: Fix warning while make xmldocs caused by dev.c
  net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
  ipv6: fix ipv6_cow_metrics for non DST_HOST case
  openvswitch: Fix key serialization.
  r8152: restore hw settings
  hso: fix rx parsing logic when skb allocation fails
  tcp: make sure skb is not shared before using skb_get()
  bridge: netfilter: Move sysctl-specific error code inside #ifdef
  ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
  ipvlan: add a missing __percpu pcpu_stats
  tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
  bgmac: fix device initialization on Northstar SoCs (condition typo)
  qlcnic: Delete existing multicast MAC list before adding new
  net/mlx5_core: Fix configuration of log_uar_page_sz
  sunvnet: don't change gso data on clones
  ...

Pull md bugfixes from Neil Brown:
 "Three bug md fixes for 3.20

  yet-another-livelock in raid5, and a problem with write errors to
  4K-block devices"

* tag 'md/3.20-fixes' of git://neil.brown.name/md:
  md/raid5: Fix livelock when array is both resyncing and degraded.
  md/raid10: round up to bdev_logical_block_size in narrow_write_error.
  md/raid1: round up to bdev_logical_block_size in narrow_write_error

Pull mcelog regression fix from Tony Luck:
 "Fix regression - functions on the mce notifier chain should not be
  able to decide that an event should not be logged"

* tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  x86/mce: Fix regression. All error records should report via /dev/mcelog

Pull DocBook build fix from Jonathan Corbet:
 "Fix the DocBook build failure caused by the move of the i2o subsystem
  to the staging tree"

* tag 'docs-fix' of git://git.lwn.net/linux-2.6:
  Fix docs build failure caused by i2o removal

Pull nfsd bugfixes from Bruce Fields:
 "These are fixes for two bugs introduced during the merge window"

* 'for-3.20' of git://linux-nfs.org/~bfields/linux:
  nfsd4: fix v3-less build
  nfsd: fix comparison in fh_fsid_match()

Commit a7854487:
  md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.

Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.

Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.

So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487
Cc: stable@vger.kernel.org (v3.7+)

Pull lazytime mount option support from Al Viro:
 "Lazytime stuff from tytso"

* 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ext4: add optimization for the lazytime mount option
  vfs: add find_inode_nowait() function
  vfs: add support for a lazytime mount option

Pull iov_iter updates from Al Viro:
 "More iov_iter work - missing counterpart of iov_iter_init() for
  bvec-backed ones and vfs_read_iter()/vfs_write_iter() - wrappers for
  sync calls of ->read_iter()/->write_iter()"

* 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: add vfs_iter_{read,write} helpers
  new helper: iov_iter_bvec()

Pull getname/putname updates from Al Viro:
 "Rework of getname/getname_kernel/etc., mostly from Paul Moore.  Gets
  rid of quite a pile of kludges between namei and audit..."

* 'getname2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  audit: replace getname()/putname() hacks with reference counters
  audit: fix filename matching in __audit_inode() and __audit_inode_child()
  audit: enable filename recording via getname_kernel()
  simpler calling conventions for filename_mountpoint()
  fs: create proper filename objects using getname_kernel()
  fs: rework getname_kernel to handle up to PATH_MAX sized filenames
  cut down the number of do_path_lookup() callers

Pull debugfs patches from Al Viro:
 "debugfs patches, mostly to make it possible for something like tracefs
  to be transparently automounted on given directory in debugfs.

  New primitive in there is debugfs_create_automount(name, parent, func,
  arg), which creates a directory and makes its ->d_automount() return
  func(arg).  Another missing primitive was debugfs_create_file_size() -
  open-coded in quite a few places.  Dave's patch adds it and converts
  the open-code instances to calling it"

* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  debugfs: Provide a file creation function that also takes an initial size
  new primitive: debugfs_create_automount()
  debugfs: split end_creating() into success and failure cases
  debugfs: take mode-dependent parts of debugfs_get_inode() into callers
  fold debugfs_mknod() into callers
  fold debugfs_create() into caller
  fold debugfs_mkdir() into caller
  debugfs_mknod(): get rid useless arguments
  fold debugfs_link() into caller
  debugfs: kill __create_file()
  debugfs: split the beginning and the end of __create_file() off
  debugfs_{mkdir,create,link}(): get rid of redundant argument

Pull misc VFS updates from Al Viro:
 "This cycle a lot of stuff sits on topical branches, so I'll be sending
  more or less one pull request per branch.

  This is the first pile; more to follow in a few.  In this one are
  several misc commits from early in the cycle (before I went for
  separate branches), plus the rework of mntput/dput ordering on umount,
  switching to use of fs_pin instead of convoluted games in
  namespace_unlock()"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  switch the IO-triggering parts of umount to fs_pin
  new fs_pin killing logics
  allow attaching fs_pin to a group not associated with some superblock
  get rid of the second argument of acct_kill()
  take count and rcu_head out of fs_pin
  dcache: let the dentry count go down to zero without taking d_lock
  pull bumping refcount into ->kill()
  kill pin_put()
  mode_t whack-a-mole: chelsio
  file->f_path.dentry is pinned down for as long as the file is open...
  get rid of lustre_dump_dentry()
  gut proc_register() a bit
  kill d_validate()
  ncpfs: get rid of d_validate() nonsense
  selinuxfs: don't open-code d_genocide()

Merge yet more updates from Andrew Morton:

 - a pile of minor fs fixes and cleanups

 - kexec updates

 - random misc fixes in various places: vmcore, rbtree, eventfd, ipc, seccomp.

 - a series of python-based kgdb helper scripts

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
  seccomp: cap SECCOMP_RET_ERRNO data to MAX_ERRNO
  samples/seccomp: improve label helper
  ipc,sem: use current->state helpers
  scripts/gdb: disable pagination while printing from breakpoint handler
  scripts/gdb: define maintainer
  scripts/gdb: convert CpuList to generator function
  scripts/gdb: convert ModuleList to generator function
  scripts/gdb: use a generator instead of iterator for task list
  scripts/gdb: ignore byte-compiled python files
  scripts/gdb: port to python3 / gdb7.7
  scripts/gdb: add basic documentation
  scripts/gdb: add lx-lsmod command
  scripts/gdb: add class to iterate over CPU masks
  scripts/gdb: add lx_current convenience function
  scripts/gdb: add internal helper and convenience function for per-cpu lookup
  scripts/gdb: add get_gdbserver_type helper
  scripts/gdb: add internal helper and convenience function to retrieve thread_info
  scripts/gdb: add is_target_arch helper
  scripts/gdb: add helper and convenience function to look up tasks
  scripts/gdb: add task iteration class
  ...

The value resulting from the SECCOMP_RET_DATA mask could exceed MAX_ERRNO
when setting errno during a SECCOMP_RET_ERRNO filter action.  This makes
sure we have a reliable value being set, so that an invalid errno will not
be ignored by userspace.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes a potential corruption with uninitialized stack memory in the
seccomp BPF sample program.

[akpm@linux-foundation.org: coding-style fixlet]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Robert Swiecki <swiecki@google.com>
Tested-by: Robert Swiecki <swiecki@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Call __set_current_state() instead of assigning the new state directly.
These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP environments, keeping
track of who changed the state.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

While reporting the (refreshed) list of modules on automatic updates we
may hit the page boundary of the output console and cause a stop if
pagination is enabled.  However, gdb does not accept user input while
running over the breakpoint handler.  So we get stuck, and the user is
forced to interrupt gdb.

Resolve this by disabling pagination during automatic symbol updates.  We
restore the user's configuration once done.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm proposing myself for keeping an eye on these scripts and integrating
contributions.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Yet another code simplification.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Analogously to the task list, convert the module list to a generator
function.  It noticeably simplifies the code.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The iterator does not return any task_struct from the thread_group list
because the first condition in the 'if not t or ...' will only be the
first time None.

Instead of keeping track of the state ourself in the next() function, we
fall back using Python's generator.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Using the gdb scripts leaves byte-compiled python files in the scripts/
directory.  These should be ignored by git.

[jan.kiszka@siemens.com: drop redundant mrproper rule as suggested by Michal]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I tried to use these scripts in an ubuntu 14.04 host (gdb 7.7 compiled
against python 3.3) but there were several errors.

I believe this patch fixes these issues so that the commands now work (I
tested lx-symbols, lx-dmesg, lx-lsmod).

Main issues that needed to be resolved:

  * In python 2 iterators have a "next()" method. In python 3 it is
    __next__() instead (so let's just add both).

  * In older python versions there was an implicit conversion
    in object.__format__() (used when an object is in string.format())
    where it was converting the object to str first and then
    calling str's __format__(). This has now been removed so
    we must explicitly convert to str the objects for which
    we need to keep this behavior.

  * In dmesg.py: in python 3 log_buf is now a "memoryview" object
    which needs to be converted to a string in order to use string
    methods like "splitlines()". Luckily memoryview exists in
    python 2.7.6 as well, so we can convert log_buf to memoryview
    and use the same code in both python 2 and python 3.

This version of the patch has now been tested with gdb 7.7 and both python
3.4 and python 2.7.6 (I think asking for at least python 2.7.6 is a
reasonable requirement instead of complicating the code with version
checks etc).
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Rob Landley <rob@landley.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This adds a lsmod-like command to list all currently loaded modules of the
target.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Will be used first to count module references.  It is optimized to read
the mask only once per stop.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is a shorthand for *$lx_per_cpu("current_task"), i.e.  a convenience
function to retrieve the currently running task of the active context.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This function allows to obtain a per-cpu variable, either of the current
or an explicitly specified CPU.

Note: sparc64 version is untested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This helper probes the type of the gdb server.  Supported are QEMU and
KGDB so far.  Knowledge about the gdb server is required e.g.  to
retrieve the current CPU or current task.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add the internal helper get_thread_info that calculates the thread_info
from a given task variable.  Also export this service as a convenience
function.

Note: ia64 version is untested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This helper caches to result of "show architecture" and matches the
provided arch (sub-)string against that output.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add the helper task_by_pid that can look up a task by its PID.  Also
export it as a convenience function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>