Atmel mXT1386 chip is operated by atmel_mxt_ts driver and it has some
different objects.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Atmel touchscreen chips have different firmware version with each chip,
so we cannot distinguish attribute of chip by firmware version.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Explicitly set all the enable bits when opening the device just in case
something left the device in an unexpected state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The AT42QT1070 QTouch sensor supports up to 7 keys.

The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it
 should work fine on other platforms.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

tslib expects pressure measurements so enable them by default for better
compatibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This patch add multitouch support for the MacBookPro8,1 and
MacBookPro8,2 models.

Cc: stable@kernel.org
Signed-off-by: Andy Botting <andy@andybotting.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There are two types of 1FGT devices supported in wacom_wac.c.
Changing them to follow the existing touchscreen format, i.e.,
only report BTN_TOUCH as a valid tool type.

Touch data will be ignored if pen is in proximity. This requires
a touch up event sent if touch was down when pen comes in. The
touch up event should be sent before any pen events are emitted.
Otherwise, two pointers would race for the cursor.

However, we can not send a touch up inside wacom_tpc_pen since
pen and touch are on different logical port. That is why we
have to check if touch is up before sending pen events.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

So it would be easier for patch reviewers to follow the data path.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

2FGT Tablet PC touch events were processed in _TAP_ format. Remove
them so we can change to _MT_ format.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The mxt_check_matrix_size() is currently setting the CTE mode to match
xline/yline information that is in the platform data, but it does not
take into account for example the fact that we could have a key array
in use too (key array would use some x/y lines as well).

It would be better to simply rely on the configuration data, and make
sure that the CTE mode set in there matches the touch object (touchscreen,
key array, proximity) configuration (which are set in the config data too).
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The MCS50XX series has a HW bug that requires explicit chip power down.
If chip is not powered down before shutting the system down the control
pins (powerup, interrupt) are pulled up and residue current continues
flowing into the chips making them continue consuming power.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Enable Runtime PM functionality in OMAP4 driver based on the following
assumptions:

- keyboard controller in wakeup domain so it is always on and power
  impact is minimal;
- in OMAP4 the device control is at module/device level and ick/fclk
  level control is difficult so cutting of clocks will prevent
  interrupts.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The test here is reversed. It should be if (IS_ERR()) instead of
if (!IS_ERR()).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Different board have different requirements/setups so let's be more
flexible.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

As there is no common configuration settings that would work in every
situation, remove the fixed config data from driver code and add
config data to platform data.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

"mXT224" is used in the Intel mid firmware in SFI tables to identify the
presence of this I2C device.
Signed-off-by: Chris Leech <christopher.leech@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to dev_pm_ops rather than bus
specific PM ops in order to facilitate core development. Do this converison
for synaptics-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The adxl34x SPI driver has what appears to be a typo referring to the
device as adx134x with the numeral 1 rather than letter l. This appears
to be an error so convert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ones in order to facilitate core development. Do this
conversion for adxl34x-spi.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ones in order to facilitate core development. Do this
conversion for adxl34x-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to use dev_pm_ops rather than
bus specific ops to facilitate core work. Do this conversion for max7359.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move away from bus specific PM operations to using
dev_pm_ops in order to facilicate core improvements. Update lm8323 to
the new model.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to use dev_pm_ops rather than
bus specific PM operations in order to facilitate core work. Do this
conversion for ad714x-spi.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There is a general move to convert drivers to use dev_pm_ops rather than
bus specific PM operations in order to facilitate core work. Do this
conversion for ad714x-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Instead of open-coding copying of data structures from userspace use
memdup_user() and strndup_user(). Note that this introduces change in
behavior because driver used to truncate 'phys' longer than 1024 bytes,
but now it will refuse to set 'phys' that long. Arguably trying to set
such 'phys' is suspect anyways.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The check for non-empty device name was botched since we tried to account
for extra space for the terminating zero at the same time. Convert to
kstrndup() to avoid this problem.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Aristeu Rozanski <aris@ruivo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Read the whole message, as reading just the first byte isn't always
guaranteed to clear the message.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Change prefixes from qt602240 to mxt to reflect that the driver supports
whole line of mXT touchscreens.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Since the driver will be supporting whole range of Atmels mXT touchscreen
controllers we better rename it to atmel_mxt_ts.
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

All users of old style get/setkeycode methids have been converted so
it is time to retire them.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

While being applied the driver was modified to add use of the ternary
operator. Write the conditionals out longhand as I find it terribly
unhelpful for legibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  NFS: NFSv4 readdir loses entries
  NFS: Micro-optimize nfs4_decode_dirent()
  NFS: Fix an NFS client lockdep issue
  NFS construct consistent co_ownerid for v4.1
  NFS: nfs_wcc_update_inode() should set nfsi->attr_gencount
  NFS improve pnfs_put_deviceid_cache debug print
  NFS fix cb_sequence error processing
  NFS do not find client in NFSv4 pg_authenticate
  NLM: Fix "kernel BUG at fs/lockd/host.c:417!" or ".../host.c:283!"
  NFS: Prevent memory allocation failure in nfsacl_encode()
  NFS: nfsacl_{encode,decode} should return signed integer
  NFS: Fix "kernel BUG at fs/nfs/nfs3xdr.c:1338!"
  NFS: Fix "kernel BUG at fs/aio.c:554!"
  NFS4: Avoid potential NULL pointer dereference in decode_and_add_ds().
  NFS: fix handling of malloc failure during nfs_flush_multi()

* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: smp_on_up: allow non-ARM SMP processors
  ARM: io: ensure inb/outb() et.al. are properly ordered on ARMv6+
  ARM: initrd: disable initrd if passed address overlaps reserved region
  ARM: footbridge: fix debug macros
  ARM: mmci: round down the bytes transferred on error
  ARM: mmci: complete the transaction on error
  ARM: 6642/1: mmci: calculate remaining bytes at error correctly

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  arch/arm/mach-omap2/dma.c: Convert IS_ERR result to PTR_ERR
  arm: omap2: mux: fix compile warning
  omap1: Simplify use of omap_irq_flags
  omap2+: Fix unused variable warning for omap_irq_base