- 25 May, 2017 40 commits
-
-
Michael J. Ruhl authored
commit 224d71f9 upstream. The only context that frees user_exp_rcv data structures is the last context closed (from a sub-context set). This leaks the allocations from the other sub-contexts. Separate the common frees from the specific frees and call them at the appropriate time. Using KEDR to check for memory leaks we get: Before test: [leak_check] Possible leaks: 25 After test: [leak_check] Possible leaks: 31 (6 leaked data structures) After patch applied (before and after test have the same value) [leak_check] Possible leaks: 25 Each leak is 192 + 13440 + 6720 = 20352 bytes per sub-context. Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Michael J. Ruhl authored
commit 94679061 upstream. If the eager buffer allocation fails, it is necessary to return an error code. Reviewed-by:
-
Fabrice Gasnier authored
commit 77a9febf upstream. When prescaler (PSC) is 0, it means div factor is 1: counter clock frequency is equal to input clk / (PSC + 1). When reload value is 8 for example, counter counts 9 cycles, from 0 to 8. This is handled in frequency write routine, by writing respectively: - prescaler - 1 to PSC - reload value - 1 to ARR This fix does the opposite when reading the frequency from PSC and ARR: - prescaler is PSC + 1 - reload value is ARR + 1 Thus, PSC may be 0, depending on requested sampling frequency (div 1). In this case, reading freq wrongly reports 0, instead of computing and reporting correct value. Remove test on !psc and !arr. Small test on stm32f4 (example on tim1_trgo), before this fix: $ cd /sys/bus/iio/devices/triggerX $ echo 10000 > sampling_frequency $ cat sampling_frequency 0 After this fix: $ echo 10000 > sampling_frequency $ cat sampling_frequency 10000 Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Andreas Klinger authored
commit ed3730c4 upstream. While calculating the compensation of the humidity there are negative values interpreted as unsigned because of unsigned variables used. These values as well as the constants need to be casted to signed as indicated by the documentation of the sensor. Signed-off-by:
Andreas Klinger <ak@it-klinger.de> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
Matt Ranostay <matt.ranostay@konsulko.com> Signed-off-by:
-
Pavel Roskin authored
commit ce420fd4 upstream. realbits, storagebits and shift should be numbers, not ASCII characters. Signed-off-by:
Pavel Roskin <plroskin@gmail.com> Reviewed-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
James Smart authored
commit 4492b739 upstream. To select the appropriate shost template, the driver is issuing a mailbox command to retrieve the wwn. Turns out the sending of the command precedes the reset of the function. On SLI-4 adapters, this is inconsequential as the mailbox command location is specified by dma via the BMBX register. However, on SLI-3 adapters, the location of the mailbox command submission area changes. When the function is first powered on or reset, the cmd is submitted via PCI bar memory. Later the driver changes the function config to use host memory and DMA. The request to start a mailbox command is the same, a simple doorbell write, regardless of submission area. So.. if there has not been a boot driver run against the adapter, the mailbox command works as defaults are ok. But, if the boot driver has configured the card and, and if no platform pci function/slot reset occurs as the os starts, the mailbox command will fail. The SLI-3 device will use the stale boot driver dma location. This can cause PCI eeh errors. Fix is to reset the sli-3 function before sending the mailbox command, thus synchronizing the function/driver on mailbox location. Note: The fix uses routines that are typically invoked later in the call flow to reset the sli-3 device. The issue in using those routines is that the normal (non-fix) flow does additional initialization, namely the allocation of the pport structure. So, rather than significantly reworking the initialization flow so that the pport is alloc'd first, pointer checks are added to work around it. Checks are limited to the routines invoked by a sli-3 adapter (s3 routines) as this fix/early call is only invoked on a sli3 adapter. Nothing changes post the fix. Subsequent initialization, and another adapter reset, still occur - both on sli-3 and sli-4 adapters. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Fixes: 96418b5e ("scsi: lpfc: Fix eh_deadline setting for sli3 adapters.") Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Bryant G. Ly authored
commit 25e78531 upstream. The driver is sending a response to the actual scsi op that was aborted by an abort task TM, while LIO is sending a response to the abort task TM. ibmvscsis_tgt does not send the response to the client until release_cmd time. The reason for this was because if we did it at queue_status time, then the client would be free to reuse the tag for that command, but we're still using the tag until the command is released at release_cmd time, so we chose to delay sending the response until then. That then caused this issue, because release_cmd is always called, even if queue_status is not. SCSI spec says that the initiator that sends the abort task TM NEVER gets a response to the aborted op and with the current code it will send a response. Thus this fix will remove that response if the CMD_T_ABORTED && !CMD_T_TAS. Another case with a small timing window is the case where if LIO sends a TMR_DOES_NOT_EXIST, and the release_cmd callback is called for the TMR Abort cmd before the release_cmd for the (attemped) aborted cmd, then we need to ensure that we send the response for the (attempted) abort cmd to the client before we send the response for the TMR Abort cmd. Signed-off-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by:
Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Johan Hovold authored
commit 49e67dd1 upstream. The memory allocator passed to __unflatten_device_tree() (e.g. a wrapped kzalloc) can fail so add the missing sanity check to avoid dereferencing a NULL pointer. Fixes: fe140423 ("of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Tyrel Datwyler authored
commit b8475cbe upstream. The call to of_find_node_by_path("/cpus") returns the cpus device_node with its reference count incremented. There is no matching of_node_put() call in of_numa_parse_cpu_nodes() which results in a leaked reference to the "/cpus" node. This patch adds an of_node_put() to release the reference. fixes: 298535c0 ("of, numa: Add NUMA of binding implementation.") Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Acked-by:
David Daney <david.daney@cavium.com> Signed-off-by:
-
Rob Herring authored
commit eb310036 upstream. sparse gives the following warning for 'pci_space': ../drivers/of/address.c:266:26: warning: incorrect type in assignment (different base types) ../drivers/of/address.c:266:26: expected unsigned int [unsigned] [usertype] pci_space ../drivers/of/address.c:266:26: got restricted __be32 const [usertype] <noident> It appears that pci_space is only ever accessed on powerpc, so the endian swap is often not needed. Signed-off-by:
-
Takashi Iwai authored
commit d66bb160 upstream. proc_create_mount_point() forgot to increase the parent's nlink, and it resulted in unbalanced hard link numbers, e.g. /proc/fs shows one less than expected. Fixes: eb6d38d5 ("proc: Allow creating permanently empty directories...") Reported-by:
Tristan Ye <tristan.ye@suse.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
Vaibhav Jain authored
commit 4f58f0bf upstream. Fix a boundary condition where in some cases an eeh event that results in card reset isn't passed on to a driver attached to the virtual PCI device associated with a slice. This will happen in case when a slice attached device driver returns a value other than PCI_ERS_RESULT_NEED_RESET from the eeh error_detected() callback. This would result in an early return from cxl_pci_error_detected() and other drivers attached to other AFUs on the card wont be notified. The patch fixes this by making sure that all slice attached device-drivers are notified and the return values from error_detected() callback are aggregated in a scheme where request for 'disconnect' trumps all and 'none' trumps 'need_reset'. Fixes: 9e8df8a2 ("cxl: EEH support") Signed-off-by:
Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Reviewed-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by:
Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Vaibhav Jain authored
commit ea9a26d1 upstream. During an eeh event when the cxl card is fenced and card sysfs attr perst_reloads_same_image is set following warning message is seen in the kernel logs: Adapter context unlocked with 0 active contexts ------------[ cut here ]------------ WARNING: CPU: 12 PID: 627 at ../drivers/misc/cxl/main.c:325 cxl_adapter_context_unlock+0x60/0x80 [cxl] Even though this warning is harmless, it clutters the kernel log during an eeh event. This warning is triggered as the EEH callback cxl_pci_error_detected doesn't obtain a context-lock before forcibly detaching all active context and when context-lock is released during call to cxl_configure_adapter from cxl_pci_slot_reset, a warning in cxl_adapter_context_unlock is triggered. To fix this warning, we acquire the adapter context-lock via cxl_adapter_context_lock() in the eeh callback cxl_pci_error_detected() once all the virtual AFU PHBs are notified and their contexts detached. The context-lock is released in cxl_pci_slot_reset() after the adapter is successfully reconfigured and before the we call the slot_reset callback on slice attached device-drivers. Fixes: 70b565bb ("cxl: Prevent adapter reset if an active context exists") Reported-by:
Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Tested-by:
Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by:
-
Gerd Hoffmann authored
commit 21a60f6e upstream. On a loaded virtualization host (dozen guests booting at the same time) it may happen that the ohci controller emulation doesn't manage to do timely frame processing, with the result that the io watchdog fires and considers the controller being dead, even though it's only the emulation being unusual slow due to the load peak. So, add a quirk for qemu and don't use the watchdog in case we figure we are running on emulated ohci. The virtual ohci controller masquerades as apple ohci controller, but we can identify it by subsystem id. Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Tobias Herzog authored
commit 1bb9914e upstream. Notifications may only be 8 bytes long. Accessing the 9th and 10th byte of unimplemented/unknown notifications may be insecure. Also check the length of known notifications before accessing anything behind the 8th byte. Signed-off-by:
Tobias Herzog <t-herzog@gmx.de> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
David Rivshin authored
commit 83977443 upstream. omap_gpio_debounce() does not validate that the requested debounce is within a range it can handle. Instead it lets the register value wrap silently, and always returns success. This can lead to all sorts of unexpected behavior, such as gpio_keys asking for a too-long debounce, but getting a very short debounce in practice. Fix this by returning -EINVAL if the requested value does not fit into the register field. If there is no debounce clock available at all, return -ENOTSUPP. Fixes: e85ec6c3 ("gpio: omap: fix omap2_set_gpio_debounce") Signed-off-by:
David Rivshin <drivshin@allworx.com> Acked-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
Ben Skeggs authored
commit 1b0f8438 upstream. If the time to the next alarm is short enough, we could race with HW and end up with an ~4 second delay until it triggers. Fix this by checking again after we update HW. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Ben Skeggs authored
commit 330bdf62 upstream. The idea here was to avoid having to "manually" program the HW if there's a new earliest alarm. This was lazy and bad, as it leads to loads of fun races between inter-related callers (ie. therm). Turns out, it's not so difficult after all. Go figure ;) Signed-off-by:
-
Ben Skeggs authored
commit 9fc64667 upstream. At least therm/fantog "attempts" to work around this issue, which could lead to corruption of the pending alarm list. Fix it properly by not updating the timestamp without the lock held, or trying to add an already pending alarm to the pending alarm list.... Signed-off-by:
-
Ben Skeggs authored
commit 3733bd8b upstream. Fixes a race where we can miss an alarm that triggers while we're already processing previous alarms. Signed-off-by:
-
Ben Skeggs authored
commit e6db9579 upstream. The DRM core used to only call prepare_fb/cleanup_fb() when a plane's framebuffer changed, which achieved the desired effect. It's apparently now up to the driver to decide on its own. Signed-off-by:
-
Ben Skeggs authored
commit 36601c2b upstream. This "optimisation" (which was originally meant to skip updating cursor settings in the core channel on position-only updates) turned out to be pointless in the final design of the code before it was merged. Remove it completely, as it breaks other cases. Signed-off-by:
-
Ben Skeggs authored
commit e4311ee5 upstream. These were ineffective due to touching the list without the alarm lock, but should no longer be required. Signed-off-by:
-
Mario Kleiner authored
commit effaf848 upstream. This apparently got lost when implementing the new DCE-6 support and would cause failures in pageflip scheduling and timestamping. Signed-off-by:
Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Mario Kleiner authored
commit e190ed1e upstream. At dot clocks > approx. 250 Mhz, some of these calcs will overflow and cause miscalculation of latency watermarks, and for some overflows also divide-by-zero driver crash ("divide error: 0000 [#1] PREEMPT SMP" in "dce_v10_0_latency_watermark+0x12d/0x190"). This zero-divide happened, e.g., on AMD Tonga Pro under DCE-10, on a Displayport panel when trying to set a video mode of 2560x1440 at 165 Hz vrefresh with a dot clock of 635.540 Mhz. Refine calculations to avoid the overflows. Tested for DCE-10 with R9 380 Tonga + ASUS ROG PG279 panel. Reviewed-by:
-
Mario Kleiner authored
commit d63c277d upstream. Avoid big roundoff errors in scanline/hactive durations for high pixel clocks, especially for >= 500 Mhz, and thereby program more accurate display fifo watermarks. Implemented here for DCE 6,8,10,11. Successfully tested on DCE 10 with AMD R9 380 Tonga. Reviewed-by:
-
Johan Hovold authored
commit ebeb3667 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: 36bcce43 ("ath9k_htc: Handle storage devices") Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Dmitry Tunin authored
commit 16ff1fb0 upstream. T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1 P: Vendor=1eda ProdID=2315 Rev=01.08 S: Manufacturer=ATHEROS S: Product=USB2.0 WLAN S: SerialNumber=12345 C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 6 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
-
Martin Schwidefsky authored
commit 07a63cbe upstream. git commit c5328901 "[S390] entry[64].S improvements" removed the update of the exit_timer lowcore field from the critical section cleanup of the .Lsysc_restore/.Lsysc_done and .Lio_restore/.Lio_done blocks. If the PSW is updated by the critical section cleanup to point to user space again, the interrupt entry code will do a vtime calculation after the cleanup completed with an exit_timer value which has *not* been updated. Due to this incorrect system time deltas are calculated. If an interrupt occured with an old PSW between .Lsysc_restore/.Lsysc_done or .Lio_restore/.Lio_done update __LC_EXIT_TIMER with the system entry time of the interrupt. Tested-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Michael Holzheu authored
commit dcc00b79 upstream. Since linux v3.14 with commit 38dfac84 ("vmcore: prevent PT_NOTE p_memsz overflow during header update") on s390 we get the following message in the kdump kernel: Warning: Exceeded p_memsz, dropping PT_NOTE entry n_namesz=0x6b6b6b6b, n_descsz=0x6b6b6b6b The reason for this is that we don't create a final zero note in the ELF header which the proc/vmcore code uses to find out the end of the notes section (see also kernel/kexec_core.c:final_note()). It still worked on s390 by chance because we (most of the time?) have the byte pattern 0x6b6b6b6b after the notes section which also makes the notes parsing code stop in update_note_header_size_elf64() because 0x6b6b6b6b is interpreded as note size: if ((real_sz + sz) > max_sz) { pr_warn("Warning: Exceeded p_memsz, dropping P ...); break; } So fix this and add the missing final note to the ELF header. We don't have to adjust the memory size for ELF header ("alloc_size") because the new ELF note still fits into the 0x1000 base memory. Signed-off-by:
Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by:
-
Richard Cochran authored
commit c90722b5 upstream. Commit 43530b69 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly") intended to replace working inline helper functions with standard regmap calls. However, it also inverted the set/clear logic of the "CORE ADJ Allowed" bit. That patch was clearly never tested, since without that bit cleared, the core VDCDC1 voltage output does not react to I2C configuration changes. This patch fixes the issue by clearing the bit as in the original, correct implementation. Note for stable back porting that, due to subsequent driver churn, this patch will not apply on every kernel version. Fixes: 43530b69 ("regulator: Use regmap_read/write(), regmap_update_bits functions directly") Signed-off-by:
Richard Cochran <rcochran@linutronix.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Wadim Egorov authored
commit 75f88115 upstream. Set the correct voltage select register for LDO2. Signed-off-by:
Wadim Egorov <w.egorov@phytec.de> Signed-off-by:
-
Linus Torvalds authored
commit 33c9e972 upstream. The code to fetch a 64-bit value from user space was entirely buggered, and has been since the code was merged in early 2016 in commit b2f68038 ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit kernels"). Happily the buggered routine is almost certainly entirely unused, since the normal way to access user space memory is just with the non-inlined "get_user()", and the inlined version didn't even historically exist. The normal "get_user()" case is handled by external hand-written asm in arch/x86/lib/getuser.S that doesn't have either of these issues. There were two independent bugs in __get_user_asm_u64(): - it still did the STAC/CLAC user space access marking, even though that is now done by the wrapper macros, see commit 11f1a4b9 ("x86: reorganize SMAP handling in user space accesses"). This didn't result in a semantic error, it just means that the inlined optimized version was hugely less efficient than the allegedly slower standard version, since the CLAC/STAC overhead is quite high on modern Intel CPU's. - the double register %eax/%edx was marked as an output, but the %eax part of it was touched early in the asm, and could thus clobber other inputs to the asm that gcc didn't expect it to touch. In particular, that meant that the generated code could look like this: mov (%eax),%eax mov 0x4(%eax),%edx where the load of %edx obviously was _supposed_ to be from the 32-bit word that followed the source of %eax, but because %eax was overwritten by the first instruction, the source of %edx was basically random garbage. The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark the 64-bit output as early-clobber to let gcc know that no inputs should alias with the output register. Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Wanpeng Li authored
commit cbfc6c91 upstream. Huawei folks reported a read out-of-bounds vulnerability in kvm pio emulation. - "inb" instruction to access PIT Mod/Command register (ioport 0x43, write only, a read should be ignored) in guest can get a random number. - "rep insb" instruction to access PIT register port 0x43 can control memcpy() in emulator_pio_in_emulated() to copy max 0x400 bytes but only read 1 bytes, which will disclose the unimportant kernel memory in host but no crash. The similar test program below can reproduce the read out-of-bounds vulnerability: void hexdump(void *mem, unsigned int len) { unsigned int i, j; for(i = 0; i < len + ((len % HEXDUMP_COLS) ? (HEXDUMP_COLS - len % HEXDUMP_COLS) : 0); i++) { /* print offset */ if(i % HEXDUMP_COLS == 0) { printf("0x%06x: ", i); } /* print hex data */ if(i < len) { printf("%02x ", 0xFF & ((char*)mem)[i]); } else /* end of block, just aligning for ASCII dump */ { printf(" "); } /* print ASCII dump */ if(i % HEXDUMP_COLS == (HEXDUMP_COLS - 1)) { for(j = i - (HEXDUMP_COLS - 1); j <= i; j++) { if(j >= len) /* end of block, not really printing */ { putchar(' '); } else if(isprint(((char*)mem)[j])) /* printable char */ { putchar(0xFF & ((char*)mem)[j]); } else /* other char */ { putchar('.'); } } putchar('\n'); } } } int main(void) { int i; if (iopl(3)) { err(1, "set iopl unsuccessfully\n"); return -1; } static char buf[0x40]; /* test ioport 0x40,0x41,0x42,0x43,0x44,0x45 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x40, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x41, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x42, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x43, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x44, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x45, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); /* ins port 0x40 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x20, %rcx;"); asm volatile ("mov $0x40, %rdx;"); asm volatile ("rep insb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); /* ins port 0x43 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x20, %rcx;"); asm volatile ("mov $0x43, %rdx;"); asm volatile ("rep insb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); return 0; } The vcpu->arch.pio_data buffer is used by both in/out instrutions emulation w/o clear after using which results in some random datas are left over in the buffer. Guest reads port 0x43 will be ignored since it is write only, however, the function kernel_pio() can't distigush this ignore from successfully reads data from device's ioport. There is no new data fill the buffer from port 0x43, however, emulator_pio_in_emulated() will copy the stale data in the buffer to the guest unconditionally. This patch fixes it by clearing the buffer before in instruction emulation to avoid to grant guest the stale data in the buffer. In addition, string I/O is not supported for in kernel device. So there is no iteration to read ioport %RCX times for string I/O. The function kernel_pio() just reads one round, and then copy the io size * %RCX to the guest unconditionally, actually it copies the one round ioport data w/ other random datas which are left over in the vcpu->arch.pio_data buffer to the guest. This patch fixes it by introducing the string I/O support for in kernel device in order to grant the right ioport datas to the guest. Before the patch: 0x000000: fe 38 93 93 ff ff ab ab .8...... 0x000008: ab ab ab ab ab ab ab ab ........ 0x000010: ab ab ab ab ab ab ab ab ........ 0x000018: ab ab ab ab ab ab ab ab ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: f6 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 4d 51 30 30 ....MQ00 0x000018: 30 30 20 33 20 20 20 20 00 3 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: f6 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 4d 51 30 30 ....MQ00 0x000018: 30 30 20 33 20 20 20 20 00 3 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ After the patch: 0x000000: 1e 02 f8 00 ff ff ab ab ........ 0x000008: ab ab ab ab ab ab ab ab ........ 0x000010: ab ab ab ab ab ab ab ab ........ 0x000018: ab ab ab ab ab ab ab ab ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: d2 e2 d2 df d2 db d2 d7 ........ 0x000008: d2 d3 d2 cf d2 cb d2 c7 ........ 0x000010: d2 c4 d2 c0 d2 bc d2 b8 ........ 0x000018: d2 b4 d2 b0 d2 ac d2 a8 ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: 00 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 00 00 00 00 ........ 0x000018: 00 00 00 00 00 00 00 00 ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ Reported-by:
Moguofang <moguofang@huawei.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Moguofang <moguofang@huawei.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Wanpeng Li authored
commit e2c2206a upstream. BUG: using __this_cpu_read() in preemptible [00000000] code: qemu-system-x86/2809 caller is __this_cpu_preempt_check+0x13/0x20 CPU: 2 PID: 2809 Comm: qemu-system-x86 Not tainted 4.11.0+ #13 Call Trace: dump_stack+0x99/0xce check_preemption_disabled+0xf5/0x100 __this_cpu_preempt_check+0x13/0x20 get_kvmclock_ns+0x6f/0x110 [kvm] get_time_ref_counter+0x5d/0x80 [kvm] kvm_hv_process_stimers+0x2a1/0x8a0 [kvm] ? kvm_hv_process_stimers+0x2a1/0x8a0 [kvm] ? kvm_arch_vcpu_ioctl_run+0xac9/0x1ce0 [kvm] kvm_arch_vcpu_ioctl_run+0x5bf/0x1ce0 [kvm] kvm_vcpu_ioctl+0x384/0x7b0 [kvm] ? kvm_vcpu_ioctl+0x384/0x7b0 [kvm] ? __fget+0xf3/0x210 do_vfs_ioctl+0xa4/0x700 ? __fget+0x114/0x210 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x23/0xc2 RIP: 0033:0x7f9d164ed357 ? __this_cpu_preempt_check+0x13/0x20 This can be reproduced by run kvm-unit-tests/hyperv_stimer.flat w/ CONFIG_PREEMPT and CONFIG_DEBUG_PREEMPT enabled. Safe access to per-CPU data requires a couple of constraints, though: the thread working with the data cannot be preempted and it cannot be migrated while it manipulates per-CPU variables. If the thread is preempted, the thread that replaces it could try to work with the same variables; migration to another CPU could also cause confusion. However there is no preemption disable when reads host per-CPU tsc rate to calculate the current kvmclock timestamp. This patch fixes it by utilizing get_cpu/put_cpu pair to guarantee both __this_cpu_read() and rdtsc() are not preempted. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Wanpeng Li authored
commit a575813b upstream. Reported by syzkaller: BUG: unable to handle kernel paging request at ffffffffc07f6a2e IP: report_bug+0x94/0x120 PGD 348e12067 P4D 348e12067 PUD 348e14067 PMD 3cbd84067 PTE 80000003f7e87161 Oops: 0003 [#1] SMP CPU: 2 PID: 7091 Comm: kvm_load_guest_ Tainted: G OE 4.11.0+ #8 task: ffff92fdfb525400 task.stack: ffffbda6c3d04000 RIP: 0010:report_bug+0x94/0x120 RSP: 0018:ffffbda6c3d07b20 EFLAGS: 00010202 do_trap+0x156/0x170 do_error_trap+0xa3/0x170 ? kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm] ? mark_held_locks+0x79/0xa0 ? retint_kernel+0x10/0x10 ? trace_hardirqs_off_thunk+0x1a/0x1c do_invalid_op+0x20/0x30 invalid_op+0x1e/0x30 RIP: 0010:kvm_load_guest_fpu.part.175+0x12a/0x170 [kvm] ? kvm_load_guest_fpu.part.175+0x1c/0x170 [kvm] kvm_arch_vcpu_ioctl_run+0xed6/0x1b70 [kvm] kvm_vcpu_ioctl+0x384/0x780 [kvm] ? kvm_vcpu_ioctl+0x384/0x780 [kvm] ? sched_clock+0x13/0x20 ? __do_page_fault+0x2a0/0x550 do_vfs_ioctl+0xa4/0x700 ? up_read+0x1f/0x40 ? __do_page_fault+0x2a0/0x550 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x23/0xc2 SDM mentioned that "The MXCSR has several reserved bits, and attempting to write a 1 to any of these bits will cause a general-protection exception(#GP) to be generated". The syzkaller forks' testcase overrides xsave area w/ random values and steps on the reserved bits of MXCSR register. The damaged MXCSR register values of guest will be restored to SSEx MXCSR register before vmentry. This patch fixes it by catching userspace override MXCSR register reserved bits w/ random values and bails out immediately. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Reviewed-by:
-
Daniel Glöckner authored
commit 1ac202e9 upstream. Modifying the attributes of a file makes ima_inode_post_setattr reset the IMA cache flags. So if the file, which has just been created, is opened a second time before the first file descriptor is closed, verification fails since the security.ima xattr has not been written yet. We therefore have to look at the IMA_NEW_FILE even if the file already existed. With this patch there should no longer be an error when cat tries to open testfile: $ rm -f testfile $ ( echo test >&3 ; touch testfile ; cat testfile ) 3>testfile A file being new is no reason to accept that it is missing a digital signature demanded by the policy. Signed-off-by:
Daniel Glöckner <dg@emlix.com> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Brian Norris authored
commit 3c8cb9ad upstream. Command buffers (skb's) are allocated by the main driver, and freed upon the last use. That last use is often in mwifiex_free_cmd_buffer(). In the meantime, if the command buffer gets used by the PCI driver, we map it as DMA-able, and store the mapping information in the 'cb' memory. However, if a command was in-flight when resetting the device (and therefore was still mapped), we don't get a chance to unmap this memory until after the core has cleaned up its command handling. Let's keep a refcount within the PCI driver, so we ensure the memory only gets freed after we've finished unmapping it. Noticed by KASAN when forcing a reset via: echo 1 > /sys/bus/pci/.../reset The same code path can presumably be exercised in remove() and shutdown(). [ 205.390377] mwifiex_pcie 0000:01:00.0: info: shutdown mwifiex... [ 205.400393] ================================================================== [ 205.407719] BUG: KASAN: use-after-free in mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] at addr ffffffc0ad471b28 [ 205.419040] Read of size 16 by task bash/1913 [ 205.423421] ============================================================================= [ 205.431625] BUG skbuff_head_cache (Tainted: G B ): kasan: bad access detected [ 205.439815] ----------------------------------------------------------------------------- [ 205.439815] [ 205.449534] INFO: Allocated in __build_skb+0x48/0x114 age=1311 cpu=4 pid=1913 [ 205.456709] alloc_debug_processing+0x124/0x178 [ 205.461282] ___slab_alloc.constprop.58+0x528/0x608 [ 205.466196] __slab_alloc.isra.54.constprop.57+0x44/0x54 [ 205.471542] kmem_cache_alloc+0xcc/0x278 [ 205.475497] __build_skb+0x48/0x114 [ 205.479019] __netdev_alloc_skb+0xe0/0x170 [ 205.483244] mwifiex_alloc_cmd_buffer+0x68/0xdc [mwifiex] [ 205.488759] mwifiex_init_fw+0x40/0x6cc [mwifiex] [ 205.493584] _mwifiex_fw_dpc+0x158/0x520 [mwifiex] [ 205.498491] mwifiex_reinit_sw+0x2c4/0x398 [mwifiex] [ 205.503510] mwifiex_pcie_reset_notify+0x114/0x15c [mwifiex_pcie] [ 205.509643] pci_reset_notify+0x5c/0x6c [ 205.513519] pci_reset_function+0x6c/0x7c [ 205.517567] reset_store+0x68/0x98 [ 205.521003] dev_attr_store+0x54/0x60 [ 205.524705] sysfs_kf_write+0x9c/0xb0 [ 205.528413] INFO: Freed in __kfree_skb+0xb0/0xbc age=131 cpu=4 pid=1913 [ 205.535064] free_debug_processing+0x264/0x370 [ 205.539550] __slab_free+0x84/0x40c [ 205.543075] kmem_cache_free+0x1c8/0x2a0 [ 205.547030] __kfree_skb+0xb0/0xbc [ 205.550465] consume_skb+0x164/0x178 [ 205.554079] __dev_kfree_skb_any+0x58/0x64 [ 205.558304] mwifiex_free_cmd_buffer+0xa0/0x158 [mwifiex] [ 205.563817] mwifiex_shutdown_drv+0x578/0x5c4 [mwifiex] [ 205.569164] mwifiex_shutdown_sw+0x178/0x310 [mwifiex] [ 205.574353] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie] [ 205.580398] pci_reset_notify+0x5c/0x6c [ 205.584274] pci_dev_save_and_disable+0x24/0x6c [ 205.588837] pci_reset_function+0x30/0x7c [ 205.592885] reset_store+0x68/0x98 [ 205.596324] dev_attr_store+0x54/0x60 [ 205.600017] sysfs_kf_write+0x9c/0xb0 ... [ 205.800488] Call trace: [ 205.802980] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190 [ 205.808415] [<ffffffc00020a96c>] show_stack+0x20/0x28 [ 205.813506] [<ffffffc0005d020c>] dump_stack+0xa4/0xcc [ 205.818598] [<ffffffc0003be44c>] print_trailer+0x158/0x168 [ 205.824120] [<ffffffc0003be5f0>] object_err+0x4c/0x5c [ 205.829210] [<ffffffc0003c45bc>] kasan_report+0x334/0x500 [ 205.834641] [<ffffffc0003c3994>] check_memory_region+0x20/0x14c [ 205.840593] [<ffffffc0003c3b14>] __asan_loadN+0x14/0x1c [ 205.845879] [<ffffffbffc46171c>] mwifiex_unmap_pci_memory.isra.14+0x4c/0x100 [mwifiex_pcie] [ 205.854282] [<ffffffbffc461864>] mwifiex_pcie_delete_cmdrsp_buf+0x94/0xa8 [mwifiex_pcie] [ 205.862421] [<ffffffbffc462028>] mwifiex_pcie_free_buffers+0x11c/0x158 [mwifiex_pcie] [ 205.870302] [<ffffffbffc4620d4>] mwifiex_pcie_down_dev+0x70/0x80 [mwifiex_pcie] [ 205.877736] [<ffffffbffc1397a8>] mwifiex_shutdown_sw+0x190/0x310 [mwifiex] [ 205.884658] [<ffffffbffc4606b4>] mwifiex_pcie_reset_notify+0xd4/0x15c [mwifiex_pcie] [ 205.892446] [<ffffffc000635f54>] pci_reset_notify+0x5c/0x6c [ 205.898048] [<ffffffc00063a044>] pci_dev_save_and_disable+0x24/0x6c [ 205.904350] [<ffffffc00063cf0c>] pci_reset_function+0x30/0x7c [ 205.910134] [<ffffffc000641118>] reset_store+0x68/0x98 [ 205.915312] [<ffffffc000771588>] dev_attr_store+0x54/0x60 [ 205.920750] [<ffffffc00046f53c>] sysfs_kf_write+0x9c/0xb0 [ 205.926182] [<ffffffc00046dfb0>] kernfs_fop_write+0x184/0x1f8 [ 205.931963] [<ffffffc0003d64f4>] __vfs_write+0x6c/0x17c [ 205.937221] [<ffffffc0003d7164>] vfs_write+0xf0/0x1c4 [ 205.942310] [<ffffffc0003d7da0>] SyS_write+0x78/0xd8 [ 205.947312] [<ffffffc000204634>] el0_svc_naked+0x24/0x28 ... [ 205.998268] ================================================================== This bug has been around in different forms for a while. It was sort of noticed in commit 955ab095 ("mwifiex: Do not kfree cmd buf while unregistering PCIe"), but it just fixed the double-free, without acknowledging the potential for use-after-free. Fixes: fc331460 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe") Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Brian Norris authored
commit 7e2f18f0 upstream. nl80211 provides the NL80211_SCAN_FLAG_RANDOM_ADDR for every scan request that should be randomized; the absence of such a flag means we should not randomize. However, mwifiex was stashing the latest randomization request and *always* using it for future scans, even those that didn't set the flag. Let's zero out the randomization info whenever we get a scan request without NL80211_SCAN_FLAG_RANDOM_ADDR. I'd prefer to remove priv->random_mac entirely (and plumb the randomization MAC properly through the call sequence), but the spaghetti is a little difficult to unravel here for me. Fixes: c2a8f0ff ("mwifiex: support random MAC address for scanning") Signed-off-by:
-
Larry Finger authored
commit 46cfa214 upstream. Current channel switch implementation sets 8812ae RFE reg value assuming that device always has type 2. Extend possible RFE types set and write corresponding reg values. Source for new code is http://dlcdnet.asus.com/pub/ASUS/wireless/PCE-AC51/DR_PCE_AC51_20232801152016.zipSigned-off-by:
Maxim Samoylov <max7255@gmail.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Yan-Hsuan Chuang <yhchuang@realtek.com> Cc: Pkshih <pkshih@realtek.com> Cc: Birming Chiu <birming@realtek.com> Cc: Shaofu <shaofu@realtek.com> Cc: Steven Ting <steventing@realtek.com> Signed-off-by:
-
