- 17 May, 2017 40 commits
-
-
Horia Geantă authored
[ Upstream commit 40c98cb5 ] RNG instantiation was previously fixed by commit 62743a41 ("crypto: caam - fix RNG init descriptor ret. code checking") while deinstantiation was not addressed. Since the descriptors used are similar, in the sense that they both end with a JUMP HALT command, checking for errors should be similar too, i.e. status code 7000_0000h should be considered successful. Cc: <stable@vger.kernel.org> # 3.13+ Fixes: 1005bccd ("crypto: caam - enable instantiation of all RNG4 state handles") Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
Frederic Barrat authored
[ Upstream commit 88b1bf72 ] Commit 4c6d9acc ("powerpc/mm: Add hooks for cxl") converted local TLB invalidates to global if the cxl driver is active. This is necessary because the CAPP snoops invalidations to forward them to the PSL on the cxl adapter. However one path was forgotten. native_flush_hash_range() still does local TLB invalidates, as found out the hard way recently. This patch fixes it by following the same logic as previously: if the cxl driver is active, the local TLB invalidates are 'upgraded' to global. Fixes: 4c6d9acc ("powerpc/mm: Add hooks for cxl") Cc: stable@vger.kernel.org # v3.18+ Signed-off-by:
Frederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Johan Hovold authored
[ Upstream commit ebeb3667 ] Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Fixes: 36bcce43 ("ath9k_htc: Handle storage devices") Cc: stable <stable@vger.kernel.org> # 2.6.39+ Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 48fe9e94 ] In the past, there was only one load-with-reservation instruction, lwarx, and if a program attempted a lwarx on a misaligned address, it would take an alignment interrupt and the kernel handler would emulate it as though it was lwzx, which was not really correct, but benign since it is loading the right amount of data, and the lwarx should be paired with a stwcx. to the same address, which would also cause an alignment interrupt which would result in a SIGBUS being delivered to the process. We now have 5 different sizes of load-with-reservation instruction. Of those, lharx and ldarx cause an immediate SIGBUS by luck since their entries in aligninfo[] overlap instructions which were not fixed up, but lqarx overlaps with lhz and will be emulated as such. lbarx can never generate an alignment interrupt since it only operates on 1 byte. To straighten this out and fix the lqarx case, this adds code to detect the l[hwdq]arx instructions and return without fixing them up, resulting in a SIGBUS being delivered to the process. Cc: stable@vger.kernel.org Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Suzuki K Poulose authored
[ Upstream commit 8b3405e3 ] In kvm_free_stage2_pgd() we don't hold the kvm->mmu_lock while calling unmap_stage2_range() on the entire memory range for the guest. This could cause problems with other callers (e.g, munmap on a memslot) trying to unmap a range. And since we have to unmap the entire Guest memory range holding a spinlock, make sure we yield the lock if necessary, after we unmap each PUD range. Fixes: commit d5d8184d ("KVM: ARM: Memory virtualization setup") Cc: stable@vger.kernel.org # v3.10+ Cc: Paolo Bonzini <pbonzin@redhat.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Christoffer Dall <christoffer.dall@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> [ Avoid vCPU starvation and lockup detector warnings ] Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Nayna Jain authored
[ Upstream commit 0afb7118 ] Currently, there is an unnecessary 1 msec delay added in i2c_nuvoton_write_status() for the successful case. This function is called multiple times during send() and recv(), which implies adding multiple extra delays for every TPM operation. This patch calls usleep_range() only if retry is to be done. Signed-off-by:
Nayna Jain <nayna@linux.vnet.ibm.com> Cc: stable@vger.kernel.org (linux-4.8) Reviewed-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by:
-
Jerry Snitselaar authored
[ Upstream commit 8569defd ] Make sure size of response buffer is at least 6 bytes, or we will underflow and pass large size_t to memcpy_fromio(). This was encountered while testing earlier version of locality patchset. Cc: stable@vger.kernel.org Fixes: 30fc8d13 ("tpm: TPM 2.0 CRB Interface") Signed-off-by:
Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by:
-
Nayna Jain authored
[ Upstream commit a233a028 ] Commit 500462a9 "timers: Switch to a non-cascading wheel" replaced the 'classic' timer wheel, which aimed for near 'exact' expiry of the timers. Their analysis was that the vast majority of timeout timers are used as safeguards, not as real timers, and are cancelled or rearmed before expiration. The only exception noted to this were networking timers with a small expiry time. Not included in the analysis was the TPM polling timer, which resulted in a longer normal delay and, every so often, a very long delay. The non-cascading wheel delay is based on CONFIG_HZ. For a description of the different rings and their delays, refer to the comments in kernel/time/timer.c. Below are the delays given for rings 0 - 2, which explains the longer "normal" delays and the very, long delays as seen on systems with CONFIG_HZ 250. * HZ 1000 steps * Level Offset Granularity Range * 0 0 1 ms 0 ms - 63 ms * 1 64 8 ms 64 ms - 511 ms * 2 128 64 ms 512 ms - 4095 ms (512ms - ~4s) * HZ 250 * Level Offset Granularity Range * 0 0 4 ms 0 ms - 255 ms * 1 64 32 ms 256 ms - 2047 ms (256ms - ~2s) * 2 128 256 ms 2048 ms - 16383 ms (~2s - ~16s) Below is a comparison of extending the TPM with 1000 measurements, using msleep() vs. usleep_delay() when configured for 1000 hz vs. 250 hz, before and after commit 500462a9. linux-4.7 | msleep() usleep_range() 1000 hz: 0m44.628s | 1m34.497s 29.243s 250 hz: 1m28.510s | 4m49.269s 32.386s linux-4.7 | min-max (msleep) min-max (usleep_range) 1000 hz: 0:017 - 2:760s | 0:015 - 3:967s 0:014 - 0:418s 250 hz: 0:028 - 1:954s | 0:040 - 4:096s 0:016 - 0:816s This patch replaces the msleep() with usleep_range() calls in the i2c nuvoton driver with a consistent max range value. Signed-of-by:
-
Nicholas Bellinger authored
[ Upstream commit 1c99de98 ] Once upon a time back in 2009, a work-around was added to support the GlobalSAN iSCSI initiator v3.3 for MacOSX, which during login did not propose nor respond to MaxBurstLength, FirstBurstLength, DefaultTime2Wait and DefaultTime2Retain keys. The work-around in iscsi_check_proposer_for_optional_reply() allowed the missing keys to be proposed, but did not require waiting for a response before moving to full feature phase operation. This allowed GlobalSAN v3.3 to work out-of-the box, and for many years we didn't run into login interopt issues with any other initiators.. Until recently, when Martin tried a QLogic 57840S iSCSI Offload HBA on Windows 2016 which completed login, but subsequently failed with: Got unknown iSCSI OpCode: 0x43 The issue was QLogic MSFT side did not propose DefaultTime2Wait + DefaultTime2Retain, so LIO proposes them itself, and immediately transitions to full feature phase because of the GlobalSAN hack. However, the QLogic MSFT side still attempts to respond to DefaultTime2Retain + DefaultTime2Wait, even though LIO has set ISCSI_FLAG_LOGIN_NEXT_STAGE3 + ISCSI_FLAG_LOGIN_TRANSIT in last login response. So while the QLogic MSFT side should have been proposing these two keys to start, it was doing the correct thing per RFC-3720 attempting to respond to proposed keys before transitioning to full feature phase. All that said, recent versions of GlobalSAN iSCSI (v5.3.0.541) does correctly propose the four keys during login, making the original work-around moot. So in order to allow QLogic MSFT to run unmodified as-is, go ahead and drop this long standing work-around. Reported-by:
Martin Svec <martin.svec@zoner.cz> Cc: Martin Svec <martin.svec@zoner.cz> Cc: Himanshu Madhani <Himanshu.Madhani@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Cc: stable@vger.kernel.org # 3.1+ Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Tobias Herzog authored
[ Upstream commit 1bb9914e ] Notifications may only be 8 bytes long. Accessing the 9th and 10th byte of unimplemented/unknown notifications may be insecure. Also check the length of known notifications before accessing anything behind the 8th byte. Signed-off-by:
Tobias Herzog <t-herzog@gmx.de> Acked-by:
Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Naoya Horiguchi authored
[ Upstream commit c9d398fa ] I found the race condition which triggers the following bug when move_pages() and soft offline are called on a single hugetlb page concurrently. Soft offlining page 0x119400 at 0x700000000000 BUG: unable to handle kernel paging request at ffffea0011943820 IP: follow_huge_pmd+0x143/0x190 PGD 7ffd2067 PUD 7ffd1067 PMD 0 [61163.582052] Oops: 0000 [#1] SMP Modules linked in: binfmt_misc ppdev virtio_balloon parport_pc pcspkr i2c_piix4 parport i2c_core acpi_cpufreq ip_tables xfs libcrc32c ata_generic pata_acpi virtio_blk 8139too crc32c_intel ata_piix serio_raw libata virtio_pci 8139cp virtio_ring virtio mii floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: cap_check] CPU: 0 PID: 22573 Comm: iterate_numa_mo Tainted: P OE 4.11.0-rc2-mm1+ #2 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:follow_huge_pmd+0x143/0x190 RSP: 0018:ffffc90004bdbcd0 EFLAGS: 00010202 RAX: 0000000465003e80 RBX: ffffea0004e34d30 RCX: 00003ffffffff000 RDX: 0000000011943800 RSI: 0000000000080001 RDI: 0000000465003e80 RBP: ffffc90004bdbd18 R08: 0000000000000000 R09: ffff880138d34000 R10: ffffea0004650000 R11: 0000000000c363b0 R12: ffffea0011943800 R13: ffff8801b8d34000 R14: ffffea0000000000 R15: 000077ff80000000 FS: 00007fc977710740(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffea0011943820 CR3: 000000007a746000 CR4: 00000000001406f0 Call Trace: follow_page_mask+0x270/0x550 SYSC_move_pages+0x4ea/0x8f0 SyS_move_pages+0xe/0x10 do_syscall_64+0x67/0x180 entry_SYSCALL64_slow_path+0x25/0x25 RIP: 0033:0x7fc976e03949 RSP: 002b:00007ffe72221d88 EFLAGS: 00000246 ORIG_RAX: 0000000000000117 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc976e03949 RDX: 0000000000c22390 RSI: 0000000000001400 RDI: 0000000000005827 RBP: 00007ffe72221e00 R08: 0000000000c2c3a0 R09: 0000000000000004 R10: 0000000000c363b0 R11: 0000000000000246 R12: 0000000000400650 R13: 00007ffe72221ee0 R14: 0000000000000000 R15: 0000000000000000 Code: 81 e4 ff ff 1f 00 48 21 c2 49 c1 ec 0c 48 c1 ea 0c 4c 01 e2 49 bc 00 00 00 00 00 ea ff ff 48 c1 e2 06 49 01 d4 f6 45 bc 04 74 90 <49> 8b 7c 24 20 40 f6 c7 01 75 2b 4c 89 e7 8b 47 1c 85 c0 7e 2a RIP: follow_huge_pmd+0x143/0x190 RSP: ffffc90004bdbcd0 CR2: ffffea0011943820 ---[ end trace e4f81353a2d23232 ]--- Kernel panic - not syncing: Fatal exception Kernel Offset: disabled This bug is triggered when pmd_present() returns true for non-present hugetlb, so fixing the present check in follow_huge_pmd() prevents it. Using pmd_present() to determine present/non-present for hugetlb is not correct, because pmd_present() checks multiple bits (not only _PAGE_PRESENT) for historical reason and it can misjudge hugetlb state. Fixes: e66f17ff ("mm/hugetlb: take page table lock in follow_huge_pmd()") Link: http://lkml.kernel.org/r/1490149898-20231-1-git-send-email-n-horiguchi@ah.jp.nec.comSigned-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: <stable@vger.kernel.org> [4.0+] Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Hui Wang authored
[ Upstream commit 2f726aec ] On this Dell AIO machine, the lineout jack does not work. We found the pin 0x1a is assigned to lineout on this machine, and in the past, we applied ALC298_FIXUP_DELL1_MIC_NO_PRESENCE to fix the heaset-set mic problem for this machine, this fixup will redefine the pin 0x1a to headphone-mic, as a result the lineout doesn't work anymore. After consulting with Dell, they told us this machine doesn't support microphone via headset jack, so we add a new fixup which only defines the pin 0x18 as the headset-mic. [rearranged the fixup insertion position by tiwai in order to make the merge with other branches easier -- tiwai] Fixes: 59ec4b57 ("ALSA: hda - Fix headset mic detection problem for two dell machines") Cc: <stable@vger.kernel.org> Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Li Qiang authored
[ Upstream commit e7e11f99 ] In vmw_surface_define_ioctl(), the 'num_sizes' is the sum of the 'req->mip_levels' array. This array can be assigned any value from the user space. As both the 'num_sizes' and the array is uint32_t, it is easy to make 'num_sizes' overflow. The later 'mip_levels' is used as the loop count. This can lead an oob write. Add the check of 'req->mip_levels' to avoid this. Cc: <stable@vger.kernel.org> Signed-off-by:
Li Qiang <liqiang6-s@360.cn> Reviewed-by:
Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by:
-
Thomas Hellstrom authored
[ Upstream commit 53e16798 ] The mesa winsys sometimes uses unimplemented parameter requests to check for features. Remove the error message to avoid bloating the kernel log. Cc: <stable@vger.kernel.org> Signed-off-by:
Brian Paul <brianp@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
-
Murray McAllister authored
[ Upstream commit 63774069 ] In vmw_get_cap_3d_ioctl(), a user can supply 0 for a size that is used in vzalloc(). This eventually calls dump_stack() (in warn_alloc()), which can leak useful addresses to dmesg. Add check to avoid a size of 0. Cc: <stable@vger.kernel.org> Signed-off-by:
Murray McAllister <murray.mcallister@insomniasec.com> Reviewed-by:
-
Murray McAllister authored
[ Upstream commit 36274ab8 ] Before memory allocations vmw_surface_define_ioctl() checks the upper-bounds of a user-supplied size, but does not check if the supplied size is 0. Add check to avoid NULL pointer dereferences. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Thomas Hellstrom authored
[ Upstream commit f7652afa ] A malicious caller could otherwise hand over handles to other objects causing all sorts of interesting problems. Testing done: Ran a Fedora 25 desktop using both Xorg and gnome-shell/Wayland. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit efb2ea77 ] This patch fixes a iscsi-target specific TMR reference leak during session shutdown, that could occur when a TMR was quiesced before the hand-off back to iscsi-target code via transport_cmd_check_stop_to_fabric(). The reference leak happens because iscsit_free_cmd() was incorrectly skipping the final target_put_sess_cmd() for TMRs when transport_generic_free_cmd() returned zero because the se_cmd->cmd_kref did not reach zero, due to the missing se_cmd assignment in original code. The result was iscsi_cmd and it's associated se_cmd memory would be freed once se_sess->sess_cmd_map where released, but the associated se_tmr_req was leaked and remained part of se_device->dev_tmr_list. This bug would manfiest itself as kernel paging request OOPsen in core_tmr_lun_reset(), when a left-over se_tmr_req attempted to dereference it's se_cmd pointer that had already been released during normal session shutdown. To address this bug, go ahead and treat ISCSI_OP_SCSI_CMD and ISCSI_OP_SCSI_TMFUNC the same when there is an extra se_cmd->cmd_kref to drop in iscsit_free_cmd(), and use op_scsi to signal __iscsit_free_cmd() when the former needs to clear any further iscsi related I/O state. Reported-by:
Rob Millner <rlm@daterainc.com> Cc: Rob Millner <rlm@daterainc.com> Reported-by:
Chu Yuan Lin <cyl@datera.io> Cc: Chu Yuan Lin <cyl@datera.io> Tested-by:
-
Sebastian Siewior authored
[ Upstream commit 9cd9a21c ] In commit 6afaf8a4 ("UBI: flush wl before clearing update marker") I managed to trigger and fix a similar bug. Now here is another version of which I assumed it wouldn't matter back then but it turns out UBI has a check for it and will error out like this: |ubi0 warning: validate_vid_hdr: inconsistent used_ebs |ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592 All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a powercut in the middle of the operation. ubi_start_update() sets the update-marker and puts all EBs on the erase list. After that userland can proceed to write new data while the old EB aren't erased completely. A powercut at this point is usually not that much of a tragedy. UBI won't give read access to the static volume because it has the update marker. It will most likely set the corrupted flag because it misses some EBs. So we are all good. Unless the size of the image that has been written differs from the old image in the magnitude of at least one EB. In that case UBI will find two different values for `used_ebs' and refuse to attach the image with the error message mentioned above. So in order not to get in the situation, the patch will ensure that we wait until everything is removed before it tries to write any data. The alternative would be to detect such a case and remove all EBs at the attached time after we processed the volume-table and see the update-marker set. The patch looks bigger and I doubt it is worth it since usually the write() will wait from time to time for a new EB since usually there not that many spare EB that can be used. Cc: stable@vger.kernel.org Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Heiko Carstens authored
[ Upstream commit d09c5373 ] Commit fd2d2b19 ("s390: get_user() should zero on failure") intended to fix s390's get_user() implementation which did not zero the target operand if the read from user space faulted. Unfortunately the patch has no effect: the corresponding inline assembly specifies that the operand is only written to ("=") and the previous value is discarded. Therefore the compiler is free to and actually does omit the zero initialization. To fix this simply change the contraint modifier to "+", so the compiler cannot omit the initialization anymore. Fixes: c9ca7841 ("s390/uaccess: provide inline variants of get_user/put_user") Fixes: fd2d2b19 ("s390: get_user() should zero on failure") Cc: stable@vger.kernel.org Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Ajay Kaher authored
USB: Proper handling of Race Condition when two USB class drivers try to call init_usb_class simultaneously [ Upstream commit 2f86a96b ] There is race condition when two USB class drivers try to call init_usb_class at the same time and leads to crash. code path: probe->usb_register_dev->init_usb_class To solve this, mutex locking has been added in init_usb_class() and destroy_usb_class(). As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class() because usb_class can never be NULL there. Signed-off-by:
Ajay Kaher <ajay.kaher@samsung.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Josh Poimboeuf authored
[ Upstream commit 61b79e16 ] Paul Menzel reported a warning: WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0 Bad frame pointer: expected f6919d98, received f6919db0 from func acpi_pm_device_sleep_wake return to c43b6f9d The warning means that function graph tracing is broken for the acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile unconditionally sets the '-Os' gcc flag to optimize for size. That's an issue because mcount-based function graph tracing is incompatible with '-Os' on x86, thanks to the following gcc bug: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109 I have another patch pending which will ensure that mcount-based function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on x86. But this patch is needed in addition to that one because the ACPI Makefile overrides that config option for no apparent reason. It has had this flag since the beginning of git history, and there's no related comment, so I don't know why it's there. As far as I can tell, there's no reason for it to be there. The appropriate behavior is for it to honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the kernel. Reported-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
-
Joerg Roedel authored
[ Upstream commit 08f63d97 ] No platform-device is required for IO(x)APICs, so don't even create them. [ rjw: This fixes a problem with leaking platform device objects after IOAPIC/IOxAPIC hot-removal events.] Signed-off-by:
Joerg Roedel <jroedel@suse.de> Cc: All applicable <stable@vger.kernel.org> Signed-off-by:
-
Ladi Prosek authored
[ Upstream commit fc865322 ] When init_vqs runs, virtio_balloon.stats is either uninitialized or contains stale values. The host updates its state with garbage data because it has no way of knowing that this is just a marker buffer used for signaling. This patch updates the stats before pushing the initial buffer. Alternative fixes: * Push an empty buffer in init_vqs. Not easily done with the current virtio implementation and violates the spec "Driver MUST supply the same subset of statistics in all buffers submitted to the statsq". * Push a buffer with invalid tags in init_vqs. Violates the same spec clause, plus "invalid tag" is not really defined. Note: the spec says: When using the legacy interface, the device SHOULD ignore all values in the first buffer in the statsq supplied by the driver after device initialization. Note: Historically, drivers supplied an uninitialized buffer in the first buffer. Unfortunately QEMU does not seem to implement the recommendation even for the legacy interface. Cc: stable@vger.kernel.org Signed-off-by:
Ladi Prosek <lprosek@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
[ Upstream commit 7ed23e1b ] On Power8 & Power9 the early CPU inititialisation in __init_HFSCR() turns on HFSCR[TM] (Hypervisor Facility Status and Control Register [Transactional Memory]), but that doesn't take into account that TM might be disabled by CPU features, or disabled by the kernel being built with CONFIG_PPC_TRANSACTIONAL_MEM=n. So later in boot, when we have setup the CPU features, clear HSCR[TM] if the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account for the CONFIG_PPC_TRANSACTIONAL_MEM=n case. Without this a KVM guest might try use TM, even if told not to, and cause an oops in the host kernel. Typically the oops is seen in __kvmppc_vcore_entry() and may or may not be fatal to the host, but is always bad news. In practice all shipping CPU revisions do support TM, and all host kernels we are aware of build with TM support enabled, so no one should actually be able to hit this in the wild. Fixes: 2a3563b0 ("powerpc: Setup in HFSCR for POWER8") Cc: stable@vger.kernel.org # v3.10+ Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by:
Sam Bobroff <sam.bobroff@au1.ibm.com> [mpe: Rewrite change log with input from Sam, add Fixes/stable] Signed-off-by:
-
Michel Dänzer authored
[ Upstream commit ce4b4f22 ] We were accidentally only overriding the first VRAM placement. For BOs with the RADEON_GEM_NO_CPU_ACCESS flag set, radeon_ttm_placement_from_domain creates a second VRAM placment with fpfn == 0. If VRAM is almost full, the first VRAM placement with fpfn > 0 may not work, but the second one with fpfn == 0 always will (the BO's current location trivially satisfies it). Because "moving" the BO to its current location puts it back on the LRU list, this results in an infinite loop. Fixes: 2a85aedd ("drm/radeon: Try evicting from CPU accessible to inaccessible VRAM first") Reported-by:
Zachary Michaels <zmichaels@oblong.com> Reported-and-Tested-by:
Julien Isorce <jisorce@oblong.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
Alan Stern authored
[ Upstream commit 16336820 ] Using KASAN, Dmitry found a bug in the rh_call_control() routine: If buffer allocation fails, the routine returns immediately without unlinking its URB from the control endpoint, eventually leading to linked-list corruption. This patch fixes the problem by jumping to the end of the routine (where the URB is unlinked) when an allocation failure occurs. Signed-off-by:
Dmitry Vyukov <dvyukov@google.com> CC: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 2d7d5400 ] When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
-
Johan Hovold authored
[ Upstream commit 03eb2a55 ] Make sure to check for the required out endpoint to avoid dereferencing a NULL-pointer in mce_request_packet should a malicious device lack such an endpoint. Note that this path is hit during probe. Fixes: 66e89522 ("V4L/DVB: IR: add mceusb IR receiver driver") Cc: stable <stable@vger.kernel.org> # 2.6.36 Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Ankur Arora authored
[ Upstream commit 1914f0cd ] This was broken in commit cd979883 ("xen/acpi-processor: fix enabling interrupts on syscore_resume"). do_suspend (from xen/manage.c) and thus xen_resume_notifier never get called on the initial-domain at resume (it is if running as guest.) The rationale for the breaking change was that upload_pm_data() potentially does blocking work in syscore_resume(). This patch addresses the original issue by scheduling upload_pm_data() to execute in workqueue context. Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: stable@vger.kernel.org Based-on-patch-by:
Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
Bjorn Andersson authored
[ Upstream commit a6566710 ] Clearing the status bit on irq_unmask will discard any pending interrupt that did arrive after the irq_ack, i.e. while the IRQ handler function was executing. Fixes: f365be09 ("pinctrl: Add Qualcomm TLMM driver") Cc: stable@vger.kernel.org Cc: Stephen Boyd <sboyd@codeaurora.org> Reported-by:
Timur Tabi <timur@codeaurora.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Adrian Hunter authored
[ Upstream commit e2ebfb21 ] Disabling interrupts for even a millisecond can cause problems for some devices. That can happen when sdhci changes clock frequency because it waits for the clock to become stable under a spin lock. The spin lock is not necessary here. Anything that is racing with changes to the I/O state is already broken. The mmc core already provides synchronization via "claiming" the host. Although the spin lock probably should be removed from the code paths that lead to this point, such a patch would touch too much code to be suitable for stable trees. Consequently, for this patch, just drop the spin lock while waiting. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Tested-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Guenter Roeck authored
[ Upstream commit f5cccf49 ] While running a bind/unbind stress test with the dwc3 usb driver on rk3399, the following crash was observed. Unable to handle kernel NULL pointer dereference at virtual address 00000218 pgd = ffffffc00165f000 [00000218] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat rfcomm xt_mark fuse bridge stp llc zram btusb btrtl btbcm btintel bluetooth ip6table_filter mwifiex_pcie mwifiex cfg80211 cdc_ether usbnet r8152 mii joydev snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async ppp_generic slhc tun CPU: 1 PID: 29814 Comm: kworker/1:1 Not tainted 4.4.52 #507 Hardware name: Google Kevin (DT) Workqueue: pm pm_runtime_work task: ffffffc0ac540000 ti: ffffffc0af4d4000 task.ti: ffffffc0af4d4000 PC is at autosuspend_check+0x74/0x174 LR is at autosuspend_check+0x70/0x174 ... Call trace: [<ffffffc00080dcc0>] autosuspend_check+0x74/0x174 [<ffffffc000810500>] usb_runtime_idle+0x20/0x40 [<ffffffc000785ae0>] __rpm_callback+0x48/0x7c [<ffffffc000786af0>] rpm_idle+0x1e8/0x498 [<ffffffc000787cdc>] pm_runtime_work+0x88/0xcc [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Source: (gdb) l *0xffffffc00080dcc0 0xffffffc00080dcc0 is in autosuspend_check (drivers/usb/core/driver.c:1778). 1773 /* We don't need to check interfaces that are 1774 * disabled for runtime PM. Either they are unbound 1775 * or else their drivers don't support autosuspend 1776 * and so they are permanently active. 1777 */ 1778 if (intf->dev.power.disable_depth) 1779 continue; 1780 if (atomic_read(&intf->dev.power.usage_count) > 0) 1781 return -EBUSY; 1782 w |= intf->needs_remote_wakeup; Code analysis shows that intf is set to NULL in usb_disable_device() prior to setting actconfig to NULL. At the same time, usb_runtime_idle() does not lock the usb device, and neither does any of the functions in the traceback. This means that there is no protection against a race condition where usb_disable_device() is removing dev->actconfig->interface[] pointers while those are being accessed from autosuspend_check(). To solve the problem, synchronize and validate device state between autosuspend_check() and usb_disconnect(). Acked-by:
Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Roger Quadros authored
[ Upstream commit 09424c50 ] The streaming_maxburst module parameter is 0 offset (0..15) so we must add 1 while using it for wBytesPerInterval calculation for the SuperSpeed companion descriptor. Without this host uvcvideo driver will always see the wrong wBytesPerInterval for SuperSpeed uvc gadget and may not find a suitable video interface endpoint. e.g. for streaming_maxburst = 0 case it will always fail as wBytePerInterval was evaluating to 0. Cc: stable@vger.kernel.org Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Marcelo Henrique Cerri authored
[ Upstream commit d82c0d12 ] Reorder the operations in decompress_kernel() to ensure initrd is moved to a safe location before the bss section is zeroed. During decompression bss can overlap with the initrd and this can corrupt the initrd contents depending on the size of the compressed kernel (which affects where the initrd is placed by the bootloader) and the size of the bss section of the decompressor. Also use the correct initrd size when checking for overlaps with parmblock. Fixes: 06c0dd72 ([S390] fix boot failures with compressed kernels) Cc: stable@vger.kernel.org Reviewed-by:
Joy Latten <joy.latten@canonical.com> Reviewed-by:
Vineetha HariPai <vineetha.hari.pai@canonical.com> Signed-off-by:
Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit c520ff3d ] When snd_seq_pool_done() is called, it marks the closing flag to refuse the further cell insertions. But snd_seq_pool_done() itself doesn't clear the cells but just waits until all cells are cleared by the caller side. That is, it's racy, and this leads to the endless stall as syzkaller spotted. This patch addresses the racy by splitting the setup of pool->closing flag out of snd_seq_pool_done(), and calling it properly before snd_seq_pool_done(). BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.comReported-and-tested-by:
-
John Garry authored
[ Upstream commit 9702c67c ] The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Cc: <stable@vger.kernel.org> Fixes: ff2aeb1e ("libata: convert to chained sg") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Marc Zyngier authored
[ Upstream commit 72f31048 ] We don't hold the mmap_sem while searching for VMAs (via find_vma), in kvm_arch_prepare_memory_region, which can end up in expected failures. Fixes: commit 8eef9123 ("arm/arm64: KVM: map MMIO regions at creation time") Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Eric Auger <eric.auger@rehat.com> Cc: stable@vger.kernel.org # v3.18+ Reviewed-by:
-
Marc Zyngier authored
[ Upstream commit 90f6e150 ] We don't hold the mmap_sem while searching for the VMAs when we try to unmap each memslot for a VM. Fix this properly to avoid unexpected results. Fixes: commit 957db105 ("arm/arm64: KVM: Introduce stage2_unmap_vm") Cc: stable@vger.kernel.org # v3.19+ Reviewed-by:
-
Bjørn Mork authored
[ Upstream commit 436ecf55 ] This is a Dell branded Sierra Wireless EM7455. Cc: <stable@vger.kernel.org> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
