- 13 Nov, 2014 40 commits
-
-
Andy Lutomirski authored
commit b47dcbdc upstream. If the TSC is unusable or disabled, then this patch fixes: - Confusion while trying to clear old APIC interrupts. - Division by zero and incorrect programming of the TSC deadline timer. This fixes boot if the CPU has a TSC deadline timer but a missing or broken TSC. The failure to boot can be observed with qemu using -cpu qemu64,-tsc,+tsc-deadline This also happens to me in nested KVM for unknown reasons. With this patch, I can boot cleanly (although without a TSC). Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Cc: Bandan Das <bsd@redhat.com> Link: http://lkml.kernel.org/r/e2fa274e498c33988efac0ba8b7e3120f7f92d78.1413393027.git.luto@amacapital.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Mathias Krause authored
commit 6891c450 upstream. If userland creates a timer without specifying a sigevent info, we'll create one ourself, using a stack local variable. Particularly will we use the timer ID as sival_int. But as sigev_value is a union containing a pointer and an int, that assignment will only partially initialize sigev_value on systems where the size of a pointer is bigger than the size of an int. On such systems we'll copy the uninitialized stack bytes from the timer_create() call to userland when the timer actually fires and we're going to deliver the signal. Initialize sigev_value with 0 to plug the stack info leak. Found in the PaX patch, written by the PaX Team. Fixes: 5a9fa730 ("posix-timers: kill ->it_sigev_signo and...") Signed-off-by:
Mathias Krause <minipli@googlemail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: PaX Team <pageexec@freemail.hu> Link: http://lkml.kernel.org/r/1412456799-32339-1-git-send-email-minipli@googlemail.comSigned-off-by:
-
Karl Beldan authored
commit c7abf25a upstream. It affects non-(V)HT rates and can lead to selecting an rts_cts rate that is not a basic rate or way superior to the reference rate (ATM rates[0] used for the 1st attempt of the protected frame data). E.g, assuming drivers register growing (bitrate) sorted tables of ieee80211_rate-s, having : - rates[0].idx == d'2 and basic_rates == b'10100 will select rts_cts idx b'10011 & ~d'(BIT(2)-1), i.e. 1, likewise - rates[0].idx == d'2 and basic_rates == b'10001 will select rts_cts idx b'10000 The first is not a basic rate and the second is > rates[0]. Also, wrt severity of the addressed misbehavior, ATM we only have one rts_cts_rate_idx rather than one per rate table entry, so this idx might still point to bitrates > rates[1..MAX_RATES]. Fixes: 5253ffb8 ("mac80211: always pick a basic rate to tx RTS/CTS for pre-HT rates") Signed-off-by:
Karl Beldan <karl.beldan@rivierawaves.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Imre Deak authored
commit 94fb823f upstream. If a device's dev_pm_ops::freeze callback fails during the QUIESCE phase, we don't rollback things correctly calling the thaw and complete callbacks. This could leave some devices in a suspended state in case of an error during resuming from hibernation. Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Peter Hurley authored
commit 37b16457 upstream. Kernel oops can cause the tty to be unreleaseable (for example, if n_tty_read() crashes while on the read_wait queue). This will cause tty_release() to endlessly loop without sleeping. Use a killable sleep timeout which grows by 2n+1 jiffies over the interval [0, 120 secs.) and then jumps to forever (but still killable). NB: killable just allows for the task to be rewoken manually, not to be terminated. Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Eric Sandeen authored
commit 5ef828c4 upstream. The commit 83e782e1 xfs: Remove incore use of XFS_OQUOTA_ENFD and XFS_OQUOTA_CHKD added a new function xfs_sb_quota_from_disk() which swaps on-disk XFS_OQUOTA_* flags for in-core XFS_GQUOTA_* and XFS_PQUOTA_* flags after the superblock is read. However, if log recovery is required, the superblock is read again, and the modified in-core flags are re-read from disk, so we have XFS_OQUOTA_* flags in memory again. This causes the XFS_QM_NEED_QUOTACHECK() test to be true, because the XFS_OQUOTA_CHKD is still set, and not XFS_GQUOTA_CHKD or XFS_PQUOTA_CHKD. Change xfs_sb_from_disk to call xfs_sb_quota_from disk and always convert the disk flags to in-memory flags. Add a lower-level function which can be called with "false" to not convert the flags, so that the sb verifier can verify exactly what was on disk, per Brian Foster's suggestion. Reported-by:
Cyril B. <cbay@excellency.fr> Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Cc: Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by:
-
Jan Kara authored
commit 474d2605 upstream. Due to a switched left and right side of an assignment, dquot_writeback_dquots() never returned error. This could result in errors during quota writeback to not be reported to userspace properly. Fix it. Coverity-id: 1226884 Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit 7938db44 upstream. The check whether quota format is set even though there are no quota files with journalled quota is pointless and it actually makes it impossible to turn off journalled quotas (as there's no way to unset journalled quota format). Just remove the check. Signed-off-by:
-
J. Bruce Fields authored
commit 51904b08 upstream. Unknown operation numbers are caught in nfsd4_decode_compound() which sets op->opnum to OP_ILLEGAL and op->status to nfserr_op_illegal. The error causes the main loop in nfsd4_proc_compound() to skip most processing. But nfsd4_proc_compound also peeks ahead at the next operation in one case and doesn't take similar precautions there. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Jason Baron authored
commit fa19ac4b upstream. Fix UE event being reported as HW_EVENT_ERR_CORRECTED. Signed-off-by:
Jason Baron <jbaron@akamai.com> Link: http://lkml.kernel.org/r/8beb13803500076fef827eab33d523e355d83759.1413405053.git.jbaron@akamai.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Jason Baron authored
commit 8030122a upstream. Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by:
-
Jason Baron authored
commit 8a3f075d upstream. Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by:
-
Jason Baron authored
commit ab0543de upstream. Fix CE event being reported as HW_EVENT_ERR_UNCORRECTED. Signed-off-by:
-
Jan Kara authored
commit 84ce0f0e upstream. When sg_scsi_ioctl() fails to prepare request to submit in blk_rq_map_kern() we jump to a label where we just end up copying (luckily zeroed-out) kernel buffer to userspace instead of reporting error. Fix the problem by jumping to the right label. CC: Jens Axboe <axboe@kernel.dk> CC: linux-scsi@vger.kernel.org Coverity-id: 1226871 Signed-off-by:
Jens Axboe <axboe@fb.com>
-
Jan Kara authored
commit ea5d05b3 upstream. If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by a multiple of BITS_PER_LONG, they will try to shift a long value by BITS_PER_LONG bits which is undefined. Change the functions to avoid the undefined shift. Coverity id: 1192175 Coverity id: 1192174 Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Wang Nan authored
commit 401507d6 upstream. Commit ff7ee93f ("cgroup/kmemleak: Annotate alloc_page() for cgroup allocations") introduces kmemleak_alloc() for alloc_page_cgroup(), but corresponding kmemleak_free() is missing, which makes kmemleak be wrongly disabled after memory offlining. Log is pasted at the end of this commit message. This patch add kmemleak_free() into free_page_cgroup(). During page offlining, this patch removes corresponding entries in kmemleak rbtree. After that, the freed memory can be allocated again by other subsystems without killing kmemleak. bash # for x in 1 2 3 4; do echo offline > /sys/devices/system/memory/memory$x/state ; sleep 1; done ; dmesg | grep leak Offlined Pages 32768 kmemleak: Cannot insert 0xffff880016969000 into the object search tree (overlaps existing) CPU: 0 PID: 412 Comm: sleep Not tainted 3.17.0-rc5+ #86 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x46/0x58 create_object+0x266/0x2c0 kmemleak_alloc+0x26/0x50 kmem_cache_alloc+0xd3/0x160 __sigqueue_alloc+0x49/0xd0 __send_signal+0xcb/0x410 send_signal+0x45/0x90 __group_send_sig_info+0x13/0x20 do_notify_parent+0x1bb/0x260 do_exit+0x767/0xa40 do_group_exit+0x44/0xa0 SyS_exit_group+0x17/0x20 system_call_fastpath+0x16/0x1b kmemleak: Kernel memory leak detector disabled kmemleak: Object 0xffff880016900000 (size 524288): kmemleak: comm "swapper/0", pid 0, jiffies 4294667296 kmemleak: min_count = 0 kmemleak: count = 0 kmemleak: flags = 0x1 kmemleak: checksum = 0 kmemleak: backtrace: log_early+0x63/0x77 kmemleak_alloc+0x4b/0x50 init_section_page_cgroup+0x7f/0xf5 page_cgroup_init+0xc5/0xd0 start_kernel+0x333/0x408 x86_64_start_reservations+0x2a/0x2c x86_64_start_kernel+0xf5/0xfc Fixes: ff7ee93f (cgroup/kmemleak: Annotate alloc_page() for cgroup allocations) Signed-off-by:
Wang Nan <wangnan0@huawei.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Michal Hocko <mhocko@suse.cz> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Yu Zhao authored
commit 5ddacbe9 upstream. Compound page should be freed by put_page() or free_pages() with correct order. Not doing so will cause tail pages leaked. The compound order can be obtained by compound_order() or use HPAGE_PMD_ORDER in our case. Some people would argue the latter is faster but I prefer the former which is more general. This bug was observed not just on our servers (the worst case we saw is 11G leaked on a 48G machine) but also on our workstations running Ubuntu based distro. $ cat /proc/vmstat | grep thp_zero_page_alloc thp_zero_page_alloc 55 thp_zero_page_alloc_failed 0 This means there is (thp_zero_page_alloc - 1) * (2M - 4K) memory leaked. Fixes: 97ae1749 ("thp: implement refcounting for huge zero page") Signed-off-by:
Yu Zhao <yuzhao@google.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: David Rientjes <rientjes@google.com> Cc: Bob Liu <lliubbo@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 19125283 upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit 90a646c7 upstream. This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140 <snip> [10251.059473] Call Trace: [10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0 [10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0 [10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0 [10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110 [10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270 <snip> The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Johan Hovold authored
commit e681286d upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51 ("USB: opticon: Add Opticon OPN2001 write support") Signed-off-by:
-
Alan Stern authored
commit 93c9bf4d upstream. Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by:
Paul Osmialowski <newchief@king.net.pl> Signed-off-by:
-
Takashi Iwai authored
commit 0725dda2 upstream. Some USB-audio devices show weird sysfs warnings at disconnecting the devices, e.g. usb 1-3: USB disconnect, device number 3 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 973 at fs/sysfs/group.c:216 device_del+0x39/0x180() sysfs group ffffffff8183df40 not found for kobject 'midiC1D0' Call Trace: [<ffffffff814a3e38>] ? dump_stack+0x49/0x71 [<ffffffff8103cb72>] ? warn_slowpath_common+0x82/0xb0 [<ffffffff8103cc55>] ? warn_slowpath_fmt+0x45/0x50 [<ffffffff813521e9>] ? device_del+0x39/0x180 [<ffffffff81352339>] ? device_unregister+0x9/0x20 [<ffffffff81352384>] ? device_destroy+0x34/0x40 [<ffffffffa00ba29f>] ? snd_unregister_device+0x7f/0xd0 [snd] [<ffffffffa025124e>] ? snd_rawmidi_dev_disconnect+0xce/0x100 [snd_rawmidi] [<ffffffffa00c0192>] ? snd_device_disconnect+0x62/0x90 [snd] [<ffffffffa00c025c>] ? snd_device_disconnect_all+0x3c/0x60 [snd] [<ffffffffa00bb574>] ? snd_card_disconnect+0x124/0x1a0 [snd] [<ffffffffa02e54e8>] ? usb_audio_disconnect+0x88/0x1c0 [snd_usb_audio] [<ffffffffa015260e>] ? usb_unbind_interface+0x5e/0x1b0 [usbcore] [<ffffffff813553e9>] ? __device_release_driver+0x79/0xf0 [<ffffffff81355485>] ? device_release_driver+0x25/0x40 [<ffffffff81354e11>] ? bus_remove_device+0xf1/0x130 [<ffffffff813522b9>] ? device_del+0x109/0x180 [<ffffffffa01501d5>] ? usb_disable_device+0x95/0x1f0 [usbcore] [<ffffffffa014634f>] ? usb_disconnect+0x8f/0x190 [usbcore] [<ffffffffa0149179>] ? hub_thread+0x539/0x13a0 [usbcore] [<ffffffff810669f5>] ? sched_clock_local+0x15/0x80 [<ffffffff81066c98>] ? sched_clock_cpu+0xb8/0xd0 [<ffffffff81070730>] ? bit_waitqueue+0xb0/0xb0 [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffff8105973e>] ? kthread+0xce/0xf0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 [<ffffffff814a8b7c>] ? ret_from_fork+0x7c/0xb0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 ---[ end trace 40b1928d1136b91e ]--- This comes from the fact that usb-audio driver may receive the disconnect callback multiple times, per each usb interface. When a device has both audio and midi interfaces, it gets called twice, and currently the driver tries to release resources at the last call. At this point, the first parent interface has been already deleted, thus deleting a child of the first parent hits such a warning. For fixing this problem, we need to call snd_card_disconnect() and cancel pending operations at the very first disconnect while the release of the whole objects waits until the last disconnect call. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931Reported-and-tested-by:
Tomas Gayoso <tgayoso@gmail.com> Reported-and-tested-by:
Chris J Arges <chris.j.arges@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Adel Gadllah authored
commit 1af39588 upstream. This device needs the quirk as well. Tested-by:
Kevin Fenzi <kevin@scrye.com> Signed-off-by:
Adel Gadllah <adel.gadllah@gmail.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Adel Gadllah authored
commit 29d05c2e upstream. This device needs the quirk as well. Signed-off-by:
-
Johan Hovold authored
commit bfe3c873 upstream. Enable the always-poll quirk for Elan Touchscreens found on some recent Samsung laptops. Without this quirk the device keeps disconnecting from the bus (and is re-enumerated) unless opened (and kept open, should an input event occur). Note that while the device can be run-time suspended, the autosuspend timeout must be high enough to allow the device to be polled at least once before being suspended. Specifically, using autosuspend_delay_ms=0 will still cause the device to disconnect on input events. Signed-off-by:
-
Johan Hovold authored
commit 0b750b3b upstream. Add quirk to make sure that a device is always polled for input events even if it hasn't been opened. This is needed for devices that disconnects from the bus unless the interrupt endpoint has been polled at least once or when not responding to an input event (e.g. after having shut down X). Signed-off-by:
-
Adel Gadllah authored
commit d7499475 upstream. Yet another device affected by this. Tested-by:
-
Adel Gadllah authored
commit 876af5d4 upstream. Currently this quirk is enabled for the model with the device id 0x0089, it is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904 as well. Signed-off-by:
-
Johan Hovold authored
commit c68929f7 upstream. Enable device-qualifier quirk for Elan Touchscreen, which often fails to handle requests for the device_descriptor. Note that the device sometimes do respond properly with a Request Error (three times as USB core retries), but usually fails to respond at all. When this happens any further descriptor requests also fails, for example: [ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd [ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71 [ 1530.945592] usb 2-7: can't read configurations, error -71 This has been observed repeating for over a minute before eventual successful enumeration. Reported-by:
Drew Von Spreecken <drewvs@gmail.com> Reported-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Johan Hovold authored
commit 2a159389 upstream. Add new quirk for devices that cannot handle requests for the device_qualifier descriptor. A USB-2.0 compliant device must respond to requests for the device_qualifier descriptor (even if it's with a request error), but at least one device is known to misbehave after such a request. Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Thomas Gleixner authored
commit d2e6d62c upstream. commit c58d80f5 ("usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq") fixed hrtimer scheduling bug. There is one left which does not trigger that often. The following scenario is still possible: lock(&x->lock); hrtimer_start(&x->t); unlock(&x->lock); expires: t->function(); lock(&x->lock); lock(&x->lock); if (!hrtimer_queued(&x->t)) hrtimer_start(&x->t); unlock(&x->lock); if (!list_empty(x->early_tx_list)) ret = HRTIMER_RESTART; -> hrtimer_forward_now(...) } else ret = HRTIMER_NORESTART; unlock(&x->lock); and the timer callback returns HRTIMER_RESTART for an armed timer. This is wrong and we run into the BUG_ON() in __run_hrtimer(). This can happens on SMP or PREEMPT-RT. The patch fixes the problem by only starting the timer if the timer is not yet queued. Reported-by:
Torben Hohn <torbenh@linutronix.de> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 2b9375b9 upstream. If PM_RUNTIME is enabled, it is easy to trigger the following backtrace on pxa2xx hosts: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8() Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104 [<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14) [<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c) [<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24) [<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8) [<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34) [<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54) [<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74) [<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8) [<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208) [<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0) [<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8) [<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc) [<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc) [<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4) [<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec) [<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24) ---[ end trace 46524156d8faa4f6 ]--- This happens because suspend function tries to disable a clock that is already disabled by runtime_suspend callback. Add if (!pm_runtime_suspended()) checks to suspend/resume path. Fixes: 7d94a505 (spi/pxa2xx: add support for runtime PM) Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Reported-by:
Andrea Adami <andrea.adami@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Alexander Stein authored
commit 5cc7b047 upstream. There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the lower 2 bits of the chip select to select a CTAR register. SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values if the chip selects 4/5 are used. For those chip selects SPI_CTAR even calculated offsets of non-existing registers. Signed-off-by:
Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by:
-
Ray Jui authored
commit 3ffa6158 upstream. When mapped RX DMA entries are unmapped in an error condition when DMA is firstly configured in the driver, the number of TX DMA entries was passed in, which is incorrect Signed-off-by:
Ray Jui <rjui@broadcom.com> Signed-off-by:
-
Jack Pham authored
commit 1200a82a upstream. On ISOC endpoints the last trb_pool entry used as a LINK TRB is not getting zeroed out correctly due to memset being called incorrectly and in the wrong place. If pool allocated from DMA was not zero-initialized to begin with this will result in the size and ctrl values being random garbage. Call memset correctly after assignment of the trb_link pointer. Fixes: f6bafc6a ("usb: dwc3: convert TRBs into bitshifts") Signed-off-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
-
Cyril Brulebois authored
commit 664d6a79 upstream. 0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle References: https://bugs.debian.org/766802Reported-by:
Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by:
Cyril Brulebois <kibi@debian.org> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Xose Vazquez Perez authored
commit 6a06e554 upstream. 0x0b05 0x17e8 RT5372 USB 2.0 bgn 2x2 ASUS USB-N14 0x0411 0x0253 RT5572 USB 2.0 abgn 2x2 BUFFALO WLP-U2-300D 0x0df6 0x0078 RT???? Sitecom N300 Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by:
-
Canek Peláez Valdés authored
commit ac0372ab upstream. Signed-off-by:
Canek Peláez Valdés <canek@ciencias.unam.mx> Signed-off-by:
-
Dan Williams authored
commit 012eee15 upstream. Port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Daniele Palmas authored
commit 2d0eb862 upstream. Add VID/PID for Telit LE910 modem. Interfaces description is almost the same than LE920, except that the qmi interface is number 2 (instead than 5). Signed-off-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
