Fix a couple of compiler warnings in dir.c caused by
potentially uninitialised variables.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

A missing initialisation when creating a new on disk inode.
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

We must not call GFP_KERNEL memory allocations while we
are holding the log lock (read or write) since that may
trigger a log flush resulting in a deadlock.

Eventually we need to fix the locking in log.c, for now
this solves the problem at the expense of freeing up memory
as fast as we would like to. This needs to be revisited
later on.

Cc: Kevin Anderson <kanderso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

This adds a generation number for the eventual use of NFS to the
ondisk inode. Its backward compatible with the current code since
it doesn't really matter what the generation number is to start with,
and indeed since its set to zero, due to it being taken from padding
in both the inode and rgrp header, it should be fine.

The eventual plan is to use this rather than no_formal_ino in the
NFS filehandles. At that point no_formal_ino will be unused.

At the same time we also add a releasepages call back to the
"normal" address space for gfs2 inodes. Also I've removed a
one-linrer function thats not required any more.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

This fixes a bug where we were releasing a page incorrectly
sometimes when reading a stuffed file. This fixes the bug
that Kevin reported when using Xen.

Cc: Kevin Anderson <kanderso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

Remove a couple of commented out, and unused lines of
code.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

This really is the correct fix this time. We just ignore all
glocks associated with inodes until the inodes are pushed
from the inode cache. At that point the glocks are queued for
reclaim, so we don't need to do it here.

Also fix one or two other minor bugs.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

It's all good.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [PKT_SCHED]: Fix error handling while dumping actions
  [PKT_SCHED]: Return ENOENT if action module is unavailable
  [PKT_SCHED]: Fix illegal memory dereferences when dumping actions

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix stack overflow checking in modular non-SMP kernels.
  [SPARC64]: Fix sparc64 build errors when CONFIG_PCI=n.

"return -err" and blindly inheriting the error code in the netlink
failure exception handler causes errors codes to be returned as
positive value therefore making them being ignored by the caller.

May lead to sending out incomplete netlink messages.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TCA_ACT_KIND attribute is used without checking its
availability when dumping actions therefore leading to a
value of 0x4 being dereferenced.

The use of strcmp() in tc_lookup_action_n() isn't safe
when fed with string from an attribute without enforcing
proper NUL termination.

Both bugs can be triggered with malformed netlink message
and don't require any privileges.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sparc64 kernel's EXPORT_SYMBOL(_mcount) is inside an
#ifdef CONFIG_SMP. This breaks modules in non-SMP kernels
built with stack overflow checking (CONFIG_STACK_DEBUG=y),
as modules_install reports:

WARNING: /lib/modules/2.6.17/kernel/drivers/ide/ide-cd.ko needs unknown symbol _mcount

Trivially fixed by moving EXPORT_SYMBOL(_mcount) outside of
the #ifdef CONFIG_SMP.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PCI] Add JMicron PCI ID constants
  [PATCH] ahci: Ensure that we don't grab both functions
  [PATCH] libata-core.c: restore configuration boot messages in ata_dev_configure(), v2
  [PATCH] sata_sil24: add suspend/sleep support
  [PATCH] sata_sil24: separate out sil24_init_controller()
  [PATCH] sata_sil: add suspend/sleep support
  [PATCH] sata_sil: separate out sil_init_controller()
  [PATCH] libata: reimplement controller-wide PM
  [PATCH] libata: reimplement per-dev PM
  [PATCH] libata: implement PM EH actions
  [PATCH] libata: separate out __ata_ehi_hotplugged()
  [PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIET
  [PATCH] libata: clean up debounce parameters and improve parameter selection
  [PATCH] libata: implement ATA_EHI_RESUME_LINK
  [PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error()
  [PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy()
  [PATCH] libata: add ap->pflags and move core dynamic flags to it
  [PATCH] libata: Conditionally set host->max_cmd_len
  [PATCH] sata_vsc: data_xfer should use mmio

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

They will be used in several IDE/libata files.
Signed-off-by: Jeff Garzik <jeff@garzik.org>

When we force the chip into dual fn mode so we get PATA and AHCI we must
be sure we don't then do anything dumb like try and grab both with the AHCI
driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This one looks better, IMHO.

This restores the default libata configuration messages printed during booting.

Signed-off-by: <petkov@math.uni-muenster.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add suspend/sleep support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out controller initialization from sil24_init_one() into
sil24_init_controller().  This will be used by resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add suspend/sleep support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out controller initialization from sil_init_one() into
sil_init_controller().  This will be used by resume.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Reimplement controller-wide PM.  ata_host_set_suspend/resume() are
defined to suspend and resume a host_set.  While suspended, EHs for
all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and
frozen.

Because SCSI device hotplug is done asynchronously against the rest of
libata EH and the same mutex is used when adding new device, suspend
cannot wait for hotplug to complete.  So, if SCSI device hotplug is in
progress, suspend fails with -EBUSY.

In most cases, host_set resume is followed by device resume.  As each
resume operation requires a reset, a single host_set-wide resume
operation may result in multiple resets.  To avoid this, resume waits
upto 1 second giving PM to request resume for devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Reimplement per-dev PM.  The original implementation directly put the
device into suspended mode and didn't synchronize w/ EH operations
including hotplug.  This patch reimplements ata_scsi_device_suspend()
and ata_scsi_device_resume() such that they request EH to perform the
respective operations.  Both functions synchronize with hotplug such
that it doesn't operate on detached devices.

Suspend waits for completion but resume just issues request and
returns.  This allows parallel wake up of devices and thus speeds up
system resume.

Due to sdev detach synchronization, it's not feasible to separate out
EH requesting from sdev handling; thus, ata_device_suspend/resume()
are removed and everything is implemented in the respective
libata-scsi functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement two PM per-dev EH actions - ATA_EH_SUSPEND and
ATA_EH_RESUME.  Each action puts the target device into suspended mode
and resumes from it respectively.

Once a device is put to suspended mode, no EH operations other than
RESUME is allowed on the device.  The device will stay suspended till
it gets resumed and thus reset and revalidated.  To implement this, a
new device state helper - ata_dev_ready() - is implemented and used in
EH action implementations to make them operate only on attached &
running devices.

If all possible devices on a port are suspended, reset is skipped too.
This prevents spurious events including hotplug events from disrupting
suspended devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Separate out __ata_ehi_hotplugged() from ata_ehi_hotplugged().  The
underscored version doesn't set AC_ERR_ATA_BUS.  This will be used for
resume which is a hotplug event but not an ATA bus error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement ATA_EHI_NO_AUTOPSY and QUIET.  These used to be implied by
ATA_PFLAG_LOADING, but new power management and PMP support need to
use these separately.  e.g. Suspend/resume operations shouldn't print
full EH messages and resume shouldn't be recorded as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The names of predefined debounce timing parameters didn't exactly
match their usages.  Rename to more generic names and implement param
selection helper sata_ehc_deb_timing() which uses EHI_HOTPLUGGED to
select params.

Combined with the previous EHI_RESUME_LINK differentiation, this makes
parameter selection accurate.  e.g. user scan resumes link but normal
deb param is used instead of hotplug param.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Implement ATA_EHI_RESUME_LINK, which indicates that the link needs to
be resumed.  This used to be implied by ATA_EHI_HOTPLUGGED.  However,
hotplug isn't the only event which requires link resume and separating
this out allows other places to request link resume.  This
differentiation also allows better debounce timing selection.

This patch converts user scan to use ATA_EHI_RESUME_LINK.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ap_lock was used because &ap->host_set->lock was too long and used a
lot.  Now that &ap->host_set->lock is replaced with ap->lock, there's
no reason to keep ap_lock.

[ed. note: that's not entirely true.  ap_lock is a local variable,
caching the results of a de-ref.  In theory, if the compiler is smart
enough, this patch is cosmetic.  However, since this is not a fast
path (it is the error path), this patch is nonetheless acceptable,
even though it _may_ introduce a performance regression.]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ata_eh_autopsy() used to directly assign determined action mask to
ehc->i.action thus overriding actions set by some of nested analyze
functions.  This patch makes ata_eh_autopsy() add action masks just as
it's done in other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ap->flags is way too clamped.  Separate out core dynamic flags to
ap->pflags.  ATA_FLAG_DISABLED is a dynamic flag but left alone as
it's referenced by a lot of LLDs and it's gonna be removed once all
LLDs are converted to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

In preparation for SAS attached SATA devices, which will
not have a libata scsi_host, only setup host->max_cmd_len
if ap->host exists.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Hi,

sata_vsc is an MMIO device, and should use the correct data_xfer
function.  This problem was introduced by:

   commit a6b2c5d4
   Author: Alan Cox <alan@lxorguk.ukuu.org.uk>
   Date:   Mon May 22 16:59:59 2006 +0100

        [PATCH] PATCH: libata. Add ->data_xfer method
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* git://git.linux-nfs.org/pub/linux/nfs-2.6:
  NLM,NFSv4: Wait on local locks before we put RPC calls on the wire
  VFS: Add support for the FL_ACCESS flag to flock_lock_file()
  NFSv4: Ensure nfs4_lock_expired() caches delegated locks
  NLM,NFSv4: Don't put UNLOCK requests on the wire unless we hold a lock
  VFS: Allow caller to determine if BSD or posix locks were actually freed
  NFS: Optimise away an excessive GETATTR call when a file is symlinked
  This fixes a panic doing the first READDIR or READDIRPLUS call when:
  NFS: Fix NFS page_state usage
  Revert "Merge branch 'odirect'"

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3711/1: AT91 timer update
  [ARM] 3709/1: pnx4008: convert to generic irq subsystem
  [ARM] 3710/1: AT91 Serial: Use GPIO API

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (39 commits)
  [PATCH] myri10ge - Export more parameters to ethtool
  [PATCH] myri10ge - Use dev_info() when printing parameters after probe
  [PATCH] myri10ge - Drop ununsed nvidia chipset id
  [PATCH] myri10ge - Drop unused pm_state
  [PATCH] Fix freeing of net device
  [PATCH] remove dead entry in net wan Kconfig
  [PATCH] NI5010 netcard cleanup
  [PATCH] lock validator: fix ns83820.c irq-flags bug
  [PATCH] pcnet32: Cleanup rx buffers after loopback test.
  [PATCH] pcnet32: Suspend the chip rather than restart when changing multicast/promisc
  [PATCH] pcnet32: Handle memory allocation failures cleanly when resizing tx/rx rings
  [PATCH] pcnet32: Use kcalloc instead of kmalloc and memset
  [PATCH] pcnet32: Fix off-by-one in get_ringparam
  [PATCH] pcnet32: Use PCI_DEVICE macro
  [PATCH] pcnet32: Fix Section mismatch error
  [PATCH] Add support for the Cicada 8201 PHY
  [PATCH] zd1211rw: disable TX queue during stop
  [PATCH] ZyDAS ZD1211 USB-WLAN driver
  [PATCH] softmac: fix build-break from 881ee6999d66c8fc903b429b73bbe6045b38c549
  [PATCH] CONFIG_WIRELESS_EXT is neccessary after all
  ...

Add the IRQ line, the tx_boundary, and whether Write-combining and MSI
are enabled to the list of parameters that are exported to ethtool.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>