The usbhs driver invokes the enable/disable APIs of the
usb tll driver in the runtime resume/suspend callbacks
of the runtime get sync and put sync of the usbhs driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The platform driver for the TLL component of the OMAP USB host controller
is implemented. Depending on the TLL hardware revision , the TLL channels
are configured. The USB HS core driver uses this driver through exported
APIs from the TLL platform driver.
usb_tll_enable and usb_tll_disble are the exported APIs of the USB TLL
platform driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Remove redundant check in is_volatile_reg().
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Move probe() and other functions from 88pm860x-i2c.c to 88pm860x-core.c.
Since it could benefit to handle DT information.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Since PREG regulator is the only one regulator in 88PM8606, and other
regulators are in 88PM8607. Checking resource as identifying regulator
is not a good way. We can use NULL resource to indentify PREG regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator support for 88pm860x regulator driver.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Remove the register offset definition. All these register offset
are transfered as IORESOURCE_REG resources.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

TWL6040 provides GPO lines to be used for controlling external devices.The number
of lines different between versions: twl6040 have 3 GPO while TWL6041 have 1.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add needed platform data structure and code to be able to load
the GPO child of twl6040.
Update the devicetree binding documentation at the same time.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci

Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci

Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci

Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add DT property "maxim,system-power-controller" to indicate whether the
PMIC is in charge of controlling the system power. If this is set, the
driver will provide the pm_power_off() function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This commit moves the driver to drivers/pwm and converts it to the new
PWM framework. In order for this to work properly, register the PWM as
child of the multi-function TWL6030 device.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Instead of reinventing macros for the same purpose, use the standard
macros.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add support when the kernel has been booted with DT blob. In this case the
pdata is NULL, we need to reach up to the core node and check if the codec
part has been enabled to determine if we need to coexist with the codec or
not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This commit adds an empty of_find_node_by_name() function for !CONFIG_OF
builds.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

twl-core has API to get the boot time configured HFCLK rate which has the
same rate as the audio MCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

To facilitate the device tree support the probe function need to be rearanged.
Small cleanup in the APLL frequency selection part as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

To clean up the module probe and remove functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Place the MODULE_* lines in the same block and add MODULE_DESCRIPTION.
Rearange the platform_driver structure at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Before the AB8500 had its own IRQ domain, the IRQ handler would take
the fired local IRQ (hwirq) and add it to the irq_base to convert it
to an IRQ number which Linux would understand (virq). However, the
IRQ base is not always used anymore since we can make use of Linear
domains. It's better to use the AB8500 hwirq -> virq mapping helper
function to convert them instead. That's what we do here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The anatop registers are accessed via syscon now, no one will use
mfd anatop driver anymore, remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Using syscon to access anatop register.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Include headfile for easy using.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Here we provide a means to probe and extract vital information
from Device Tree when booting with it enabled. Without this
patch sub-devices wouldn't be able to reference the tc3589x
from Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

In preparation for Device Tree enablement all IRQ controllers
should control their own IRQ domain. This patch provides just
that.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Using kfree to free data allocated with devm_kzalloc causes double frees.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x;
@@

x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.

The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>

Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>

During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
  C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds the Watchdog Timer Device IDs for the Intel Lynx Point-LP PCH.
The Device IDs are defined in drivers/mfd/lpc_ich.c
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.

This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

WARNING: drivers/built-in.o(.data+0x1e3c8): Section mismatch in
reference from the variable bk_devs to the variable
.devinit.data:bk0_resources
The variable bk_devs references
the variable __devinitdata bk0_resources
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console

So add __devinitdata on bk_devs, led_devs & reg_devs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".

Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>