commit 907eda32 upstream.

This reverts commit 068500e0.

According to some tests, SDMA support is broken at least for i.MX6 without
HW flow control. Different forms of data-corruption appear either with
the ROM firmware for the SDMA controller as well as when loading Freescale
provided SDMA firmware versions 1.1 or 3.1.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5fb2c782 upstream.

This device automatically switches itself to another mode (0x1405)
unless the specific access pattern of Windows is followed in its
initial mode. That makes a dirty unmount of the internal storage
devices inevitable if they are mounted. So the card reader of
such a device should be ignored, lest an unclean removal become
inevitable.

This replaces an earlier patch that ignored all LUNs of this device.
That patch was overly broad.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 945b4744 upstream.

This commit adds the necessary quirk to make the Marvell 4140 SATA PMP
work properly. This PMP doesn't like SRST on port number 4 (the host
port) so this commit marks this port as not supporting SRST.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 32c848e3 upstream.

Status of enabling suspend mode for regulator was stored in bitmap-like
long integer.

However since adding support for S2MPU02 the number of regulators
exceeded 32 so on devices with more than 32 regulators (S2MPU02 and
S2MPS13) overflow happens when shifting the bit. This could lead to
enabling suspend mode for completely different regulator than intended
or to switching different regulator to other mode (e.g. from always
enabled to controlled by PWRHOLD pin). Both cases could result in larger
energy usage and issues when suspending to RAM.

Fixes: 00e2573d ("regulator: s2mps11: Add support S2MPU02 regulator device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5f6c2d2b upstream.

When a blkcg configuration is targeted to a partition rather than a
whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it
forgets to put the gendisk ref in that case.  Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 96849170 upstream.

This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen.  Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.

According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.

The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3f81d244 upstream.

We were previously using free_bootmem() and just getting lucky
that nothing too bad happened.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f6ee9b58 upstream.

DMA transfers must be greater than the watermark level size. spi_imx->rx_wml
and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct
spi_transfer contains the transfer len in bytes. Fix the check if DMA is
possible for a transfer accordingly. This fixes transfers with sizes between
33 and 128 bytes for which previously was claimed that DMA is possible.

Fixes: f62caccd (spi: spi-imx: add DMA support)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6a806a21 upstream.

Setting the Same Edge bit indicates to the spfi block to receive and
transmit data on the same edge of the spfi clock, which in turn
doubles the operating frequency of spfi.

The maximum supported frequency is limited to 1/4th of the spfi input
clock, but without this bit set the maximum would be 1/8th of the
input clock.

The current driver calculates the divisor with maximum speed at 1/4th
of the input clock, this would fail if the requested frequency is
higher than 1/8 of the input clock. Any requests for 1/8th of the
input clock would still pass.

Fixes: 8543d0e7 ("spi: img-spfi: Limit bit clock to 1/4th of input clock")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 34cab6f4 upstream.

When we get a read error from the last working device, we don't
try to repair it, and don't fail the device.  We simple report a
read error to the caller.

However the current test for 'is this the last working device' is
wrong.
When there is only one fully working device, it assumes that a
non-faulty device is that device.  However a spare which is rebuilding
would be non-faulty but so not the only working device.

So change the test from "!Faulty" to "In_sync".  If ->degraded says
there is only one fully working device and this device is in_sync,
this must be the one.

This bug has existed since we allowed read_balance to read from
a recovering spare in v3.0
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes: 76073054 ("md/raid1: clean up read_balance.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f9e5554c upstream.

For 8000 series, we need to access the device to know what
firmware to load. Before we do so, we need to prepare the
device otherwise we might not be able to access the
hardware.

Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit be88a1ad upstream.

This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 923a8c1d upstream.

When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181

Fixes: 34c8b24f ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6debce6f upstream.

Current implementation of cp2112_raw_event() only accepts one data report at a
time. If last received data report is not fully handled yet, a new incoming
data report will overwrite it. In such case we don't guaranteed to propagate
the correct incoming data.

The trivial fix implemented here forces a single report at a time by requesting
in cp2112_read() no more than 61 byte of data, which is the payload size of a
single data report.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9cd76049 upstream.

pdev->dev.platform_data is not initialized if match is true in function
sdhci_pxav3_probe. Just local variable pdata is assigned the return value
from function pxav3_get_mmc_pdata().

static int sdhci_pxav3_probe(struct platform_device *pdev) {

    struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
    ...
    if (match) {
		ret = mmc_of_parse(host->mmc);
		if (ret)
			goto err_of_parse;
		sdhci_get_of_property(pdev);
		pdata = pxav3_get_mmc_pdata(dev);
     }
     ...
}
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Fixes: b650352d("mmc: sdhci-pxa: Add device tree support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e91125f upstream.

Support for 8BIT bus with was added some time ago to sdhci-esdhc but
then missed to remove the 8BIT from the reserved bit mask which made
8BIT non functional.

Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7ac02036 upstream.

We should not call dma_free_coherent if host->adma_table is NULL,
otherwise may trigger panic.

Fixes: d1e49f77 ("mmc: sdhci: convert ADMA descriptors to a...")
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 408806f7 upstream.

DTO/DCRC errors were not being informed to the mmc core since
commit ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC
errors. This is because after this commit 'host->data' is checked after
it has been cleared to NULL by omap_hsmmc_dma_cleanup().

Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked
making core layer not to be aware of DTO/DCRC errors. Because of this
any command invoked after DTO/DCRC error leads to a hang.

Fix this by checking for 'host->data' before it is actually cleared.

Fixes: ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of
HSMMC IRQ")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 46ebb7af upstream.

This continues the attempt to fix commit fb170fb4 ("iommu/vt-d:
Introduce helper functions to make code symmetric for readability").
The previous attempt in commit 71684406 ("iommu/vt-d: Detach
domain *only* from attached iommus") overlooked the fact that
dmar_domain.iommu_bmp gets cleared for VM domains when devices are
detached:

intel_iommu_detach_device
  domain_remove_one_dev_info
    domain_detach_iommu

The domain is detached from the iommu, but the iommu is still attached
to the domain, for whatever reason.  Thus when we get to domain_exit(),
we can't rely on iommu_bmp for VM domains to find the active iommus,
we must check them all.  Without that, the corresponding bit in
intel_iommu.domain_ids doesn't get cleared and repeated VM domain
creation and destruction will run out of domain IDs.  Meanwhile we
still can't call iommu_detach_domain() on arbitrary non-VM domains or
we risk clearing in-use domain IDs, as 71684406 attempted to
address.

It's tempting to modify iommu_detach_domain() to test the domain
iommu_bmp, but the call ordering from domain_remove_one_dev_info()
prevents it being able to work as fb170fb4 seems to have intended.
Caching of unused VM domains on the iommu object seems to be the root
of the problem, but this code is far too fragile for that kind of
rework to be proposed for stable, so we simply revert this chunk to
its state prior to fb170fb4.

Fixes: fb170fb4 ("iommu/vt-d: Introduce helper functions to make
                      code symmetric for readability")
Fixes: 71684406 ("iommu/vt-d: Detach domain *only* from attached
                      iommus")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e3eea140 upstream.

Commit 4104d326 ("ftrace: Remove global function list and call function
directly") simplified the ftrace code by removing the global_ops list with a
new design. But this cleanup also broke the filtering of PIDs that are added
to the set_ftrace_pid file.

Add back the proper hooks to have pid filtering working once again.
Reported-by: Matt Fleming <matt@console-pimps.org>
Reported-by: Richard Weinberger <richard.weinberger@gmail.com>
Tested-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fe78fcc8 upstream.

The handling of in detach_mounts of unmounted but connected mounts is
buggy and can lead to an infinite loop.

Correct the handling of unmounted mounts in detach_mount.  When the
mountpoint of an unmounted but connected mount is connected to a
dentry, and that dentry is deleted we need to disconnect that mount
from the parent mount and the deleted dentry.

Nothing changes for the unmounted and connected children.  They can be
safely ignored.

Fixes: ce07d891 mnt: Honor MNT_LOCKED when detaching mounts
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2d0a123 upstream.

rmdir mntpoint will result in an infinite loop when there is
a mount locked on the mountpoint in another mount namespace.

This is because the logic to test to see if a mount should
be disconnected in umount_tree is buggy.

Move the logic to decide if a mount should remain connected to
it's mountpoint into it's own function disconnect_mount so that
clarity of expression instead of terseness of expression becomes
a virtue.

When the conditions where it is invalid to leave a mount connected
are first ruled out, the logic for deciding if a mount should
be disconnected becomes much clearer and simpler.

Fixes: e0c9c0af mnt: Update detach_mounts to leave mounts connected
Fixes: ce07d891 mnt: Honor MNT_LOCKED when detaching mounts
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9571b25d upstream.

imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165 which removed some entries from the array and so made it
wrong to access the array by pin id.

The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.

This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.

Fixes: 607af165 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4479004e upstream.

If we don't do this, and we then fail to recreate the debugfs
directory during a mode change, then we will fail later trying
to add stations to this now bogus directory:

BUG: unable to handle kernel NULL pointer dereference at 0000006c
IP: [<c0a92202>] mutex_lock+0x12/0x30
Call Trace:
[<c0678ab4>] start_creating+0x44/0xc0
[<c0679203>] debugfs_create_dir+0x13/0xf0
[<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211]
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 56551da9 upstream.

Incorrect register offset used for sthi407 clockgenC
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: 51306d56 ("clk: st: STiH407: Support for clockgenC0")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3be6d8ce upstream.

This patch fixes the mux bit-setting for ClockgenA9.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: 13e6f2da ("clk: st: STiH407: Support for A9 MUX Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0f4f2afd upstream.

While proving lock, the following warning happens
and it is fixed after initializing lock in the setup
function

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.27-02861-g39df285-dirty #33
[<c00154ac>] (unwind_backtrace+0x0/0xf4) from [<c0011b50>] (show_stack+0x10/0x14)
[<c0011b50>] (show_stack+0x10/0x14) from [<c00689ac>] (__lock_acquire+0x900/0xb14)
[<c00689ac>] (__lock_acquire+0x900/0xb14) from [<c0069394>] (lock_acquire+0x68/0x7c)
[<c0069394>] (lock_acquire+0x68/0x7c) from [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c)
[<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<c0381e6c>] (clk_gate_endisable+0x28/0x88)
[<c0381e6c>] (clk_gate_endisable+0x28/0x88) from [<c0381ee0>] (clk_gate_enable+0xc/0x14)
[<c0381ee0>] (clk_gate_enable+0xc/0x14) from [<c0386c68>] (flexgen_enable+0x28/0x40)
[<c0386c68>] (flexgen_enable+0x28/0x40) from [<c037f260>] (__clk_enable+0x5c/0x9c)
[<c037f260>] (__clk_enable+0x5c/0x9c) from [<c037f558>] (clk_enable+0x18/0x2c)
[<c037f558>] (clk_enable+0x18/0x2c) from [<c064a1dc>] (st_lpc_of_register+0xc0/0x248)
[<c064a1dc>] (st_lpc_of_register+0xc0/0x248) from [<c0649e44>] (clocksource_of_init+0x34/0x58)
[<c0649e44>] (clocksource_of_init+0x34/0x58) from [<c0637ddc>] (sti_timer_init+0x10/0x18)
[<c0637ddc>] (sti_timer_init+0x10/0x18) from [<c06343f8>] (time_init+0x20/0x30)
[<c06343f8>] (time_init+0x20/0x30) from [<c0632984>] (start_kernel+0x20c/0x2e8)
[<c0632984>] (start_kernel+0x20c/0x2e8) from [<40008074>] (0x40008074)
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: b1165170 ("clk: st: STiH407: Support for Flexgen Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e7ac6c66 upstream.

Two SLES11 SP3 servers encountered similar crashes simultaneously
following some kind of SAN/tape target issue:

...
qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 --  1 2002.
qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 --  1 2002.
qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0.
qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2.
qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2.
qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps).
qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2.
qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000.
 rport-3:0-0: blocked FC remote port time out: removing target and saving binding
qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps).
qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2.
 rport-2:0-0: blocked FC remote port time out: removing target and saving binding
sg_rq_end_io: device detached
BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8
IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP
CPU 0
...
Supported: No, Proprietary modules are loaded [1739975.390463]
Pid: 27965, comm: ABCD Tainted: PF           X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8
RIP: 0010:[<ffffffff8133b268>]  [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
RSP: 0018:ffff8839dc1e7c68  EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138
RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0
R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001
R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80
FS:  00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640)
Stack:
 ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80
 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000
 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e
Call Trace:
 [<ffffffffa03fa309>] st_open+0x129/0x240 [st]
 [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200
 [<ffffffff811588a8>] __dentry_open+0x198/0x310
 [<ffffffff81167d74>] do_last+0x1f4/0x800
 [<ffffffff81168fe9>] path_openat+0xd9/0x420
 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0
 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250
 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b
 [<00007f8e4f617fd0>] 0x7f8e4f617fcf
Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0
RIP  [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90
 RSP <ffff8839dc1e7c68>
CR2: 00000000000002a8

Analysis reveals the cause of the crash to be due to STp->device
being NULL. The pointer was NULLed via scsi_tape_put(STp) when it
calls scsi_tape_release(). In st_open() we jump to err_out after
scsi_block_when_processing_errors() completes and returns the
device as offline (sdev_state was SDEV_DEL):

1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host
1181    module count. */
1182 static int st_open(struct inode *inode, struct file *filp)
1183 {
1184         int i, retval = (-EIO);
1185         int resumed = 0;
1186         struct scsi_tape *STp;
1187         struct st_partstat *STps;
1188         int dev = TAPE_NR(inode);
1189         char *name;
...
1217         if (scsi_autopm_get_device(STp->device) < 0) {
1218                 retval = -EIO;
1219                 goto err_out;
1220         }
1221         resumed = 1;
1222         if (!scsi_block_when_processing_errors(STp->device)) {
1223                 retval = (-ENXIO);
1224                 goto err_out;
1225         }
...
1264  err_out:
1265         normalize_buffer(STp->buffer);
1266         spin_lock(&st_use_lock);
1267         STp->in_use = 0;
1268         spin_unlock(&st_use_lock);
1269         scsi_tape_put(STp); <-- STp->device = 0 after this
1270         if (resumed)
1271                 scsi_autopm_put_device(STp->device);
1272         return retval;

The ref count for the struct scsi_tape had already been reduced
to 1 when the .remove method of the st module had been called.
The kref_put() in scsi_tape_put() caused scsi_tape_release()
to be called:

0266 static void scsi_tape_put(struct scsi_tape *STp)
0267 {
0268         struct scsi_device *sdev = STp->device;
0269
0270         mutex_lock(&st_ref_mutex);
0271         kref_put(&STp->kref, scsi_tape_release); <-- calls this
0272         scsi_device_put(sdev);
0273         mutex_unlock(&st_ref_mutex);
0274 }

In scsi_tape_release() the struct scsi_device in the struct
scsi_tape gets set to NULL:

4273 static void scsi_tape_release(struct kref *kref)
4274 {
4275         struct scsi_tape *tpnt = to_scsi_tape(kref);
4276         struct gendisk *disk = tpnt->disk;
4277
4278         tpnt->device = NULL; <<<---- where the dev is nulled
4279
4280         if (tpnt->buffer) {
4281                 normalize_buffer(tpnt->buffer);
4282                 kfree(tpnt->buffer->reserved_pages);
4283                 kfree(tpnt->buffer);
4284         }
4285
4286         disk->private_data = NULL;
4287         put_disk(disk);
4288         kfree(tpnt);
4289         return;
4290 }

Although the problem was reported on SLES11.3 the problem appears
in linux-next as well.

The crash is fixed by reordering the code so we no longer access
the struct scsi_tape after the kref_put() is done on it in st_open().
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Signed-off-by: Darren Lavender <darren.lavender@hp.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0c958ecc upstream.

Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.

__sg_alloc_table() sets both table->nents and table->orig_nents to the
same value.  When the scatterlist is DMA-mapped, table->nents is
overwritten with the (possibly smaller) size of the DMA-mapped
scatterlist, while table->orig_nents retains the original size of the
allocated scatterlist.  scsi_free_sgtable() should therefore check
orig_nents instead of nents, and all code that initializes sdb->table
without calling __sg_alloc_table() should set both nents and orig_nents.

Fixes: d285203c ("scsi: add support for a blk-mq based I/O path.")
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1278dd68 upstream.

Commit 1e6f2416 changed the scsi sysfs 'queue_depth' code to
rejects depths higher than the scsi host template setting. But lots
of hosts set this to 1, and update the settings in the scsi host
when the controller/devices probing happens.

This breaks (at least) mpt2sas and mpt3sas runtime setting of queue
depth, returning EINVAL for all settings but '1'. And once it's set to
1, there's no way to go back up.

Fixes: 1e6f2416 "scsi: don't allow setting of queue_depth bigger than can_queue"
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 591e5bec upstream.

The GICv3 ITS architecture allows a given [DevID, EventID] pair to be
translated to a [LPI, Collection] pair, where DevID is the device writing
the MSI, EventID is the payload being written, LPI is the actual
interrupt number, and Collection is roughly equivalent to a target CPU.

Each LPI can be mapped to a separate collection, but the ITS driver
insists on maintaining the collection on a device basis, instead of doing
it on a per interrupt basis.

This is obviously flawed, and this patch fixes it by adding a per interrupt
index that indicates which collection number is in use.
Reported-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1437126402-11677-1-git-send-email-marc.zyngier@arm.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 621739b0 upstream.

This reverts commit 9a0e609e.
(Resolved a conflict during revert due to commit bfebd1cd that came
after)

This revert is motivated by a couple failure reports on request-based DM
multipath testbeds:
1) Netapp reported that their multipath fault injection test under heavy
   IO load can stall longer than 300 seconds.
2) IBM reported elevated lock contention in their testbed (likely due to
   increased back pressure due to IO not being dispatched as quickly):
   https://www.redhat.com/archives/dm-devel/2015-July/msg00057.htmlSigned-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a833581e upstream.

Mikulas reported his K6-3 not booting. This is because the
static_key API confusion struck and bit Andy, this wants to be
static_key_false().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Vince Weaver <vince@deater.net>
Cc: hillf.zj <hillf.zj@alibaba-inc.com>
Fixes: a6673429 ("perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks")
Link: http://lkml.kernel.org/r/20150709172338.GC19282@twins.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 649ccd08 upstream.

MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition.  It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2d1cb7f6 upstream.

Add the correct dB ranges of Bose Companion 5 and Drangonfly DAC 1.2.
Signed-off-by: Yao-Wen Mao <yaowen@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3a05d12f upstream.

Dell Vostro 5480 (1028:069a) needs the very same quirk used for Vostro
5470 model to make bass speakers properly working.
Reported-and-tested-by: Paulo Roberto de Oliveira Castro <p.oliveira.castro@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b9d9c9ef upstream.

Toshiba Satellite S50D has another model with a different PCI SSID
(1179:fa93) while the previous fixup was for 1179:fa91.  Adjust the
fixup entry with SND_PCI_QUIRK_MASK() to match with both devices.
Reported-by: Tim Sample <timsample@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cba59972 upstream.

Without this patch, the headset mic will not work on this machine.

BugLink: https://bugs.launchpad.net/bugs/1476987Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6c3d9119 upstream.

Vendor ID 0x10de007d is used by a yet-to-be-named GPU chip.

This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is
appropriate here.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5022813d upstream.

Fixes audio problems on newer asics
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>