- 18 May, 2010 40 commits
-
-
Alex Deucher authored
Signed-off-by:
Alex Deucher <alexdeucher@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
Dave Airlie authored
since derefing the object might free it. Signed-off-by: -
Alex Deucher authored
- disable gui idle interrupt use Seems to hang some r5xx chips - move vbl range check into existing vbl check function in radeon_pm.c - disable crtc mc acccess for the whole reclocking process Signed-off-by:
-
Ben Skeggs authored
Will be used by nouveau driver also in the near future. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Matthew Garrett authored
This seems to be relatively stable now, so enable it for these chipsets too. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
Matthew Garrett authored
The vblank interrupt on r600 doesn't seem to be especially reliable, so perform some sanity checks before the actual reclock. Signed-off-by:
-
Matthew Garrett authored
The ttm code could take vram_mutex followed by cp_mutex, while the reclocking code would do the reverse. Hilarity could ensue. Signed-off-by:
-
Matthew Garrett authored
We need to choose the correct PM state to transition into before starting the actual change. Call radeon_get_power_state() at the top of the clock setting to do so. Signed-off-by:
-
Matthew Garrett authored
With luck, dynamic memory reclocking on r600 should be stable with the previous patches. Enable it. Signed-off-by:
-
Matthew Garrett authored
The ttm bo workqueue may touch objects while we're reclocking, so make sure it's blocked until we're done. Signed-off-by:
-
Matthew Garrett authored
We want to be able to prevent the delayed workqueue from changing state while we're reclocking, so add an API to block and unblock it. Signed-off-by:
-
Matthew Garrett authored
We need to block the drm core from doing anything that may touch our vram during reclock, so take the drm mutex for the duration. Signed-off-by:
-
Matthew Garrett authored
Touching vram while the card is reclocking can lead to lockups. Unmap any pages that could be touched by the CPU and block any accesses to vram until the reclocking is complete. Signed-off-by:
-
Matthew Garrett authored
There's a moderate amount of effort involved in setting the card up for clock transitions, so unify the codepaths to make it easier to implement. Signed-off-by:
-
Alex Deucher authored
Add two new sysfs attributes: - dynpm - power_state Echoing 0/1 to dynpm disables/enables dynamic power management. The driver scales the sclk dynamically based on the number of queued fences. dynpm only scales sclk dynamically in single head mode. Echoing x.y to power_state selects a static power state (x) and clock mode (y). This allows you to statically select a power state and clock mode. Selecting a static clock mode will disable dynpm. Signed-off-by:
-
Alex Deucher authored
- pm_misc() - handles voltage, pcie lanes, and other non clock related power mode settings. Currently disabled. Needs further debugging - pm_prepare() - disables crtc mem requests right now. All memory clients need to be disabled when changing memory clocks. This function can be expanded to include disabling fb access as well. - pm_finish() - enable active memory clients. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
- remove non_clock_info struct - track power state misc flags Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
Just adds overhead when the power state will never change. Signed-off-by:
-
Alex Deucher authored
Hook the atom table parsing up to module loading, so we can automatically load the appropriate hwmon drivers. Based on initial patch for r6xx from Matthew Garrett Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
This also simplifies the code and enables reclocking with multiple heads active by tracking whether the power states are single or multi-head capable. Eventually, we will want to select a power state based on external factors (AC/DC state, user selection, etc.). (v2) Update for evergreen Signed-off-by:
-
Alex Deucher authored
(v2) Add evergreen vbl checks Signed-off-by:
-
Alex Deucher authored
crtcs are what we ultimately care about wrt to pm. Signed-off-by:
-
Alex Deucher authored
Signed-off-by:
-
Alex Deucher authored
On pre-r6xx, the power mode array is usually ordered: low ... high default On r6xx+: default low ... high Signed-off-by:
-
Alex Deucher authored
set proper wait condition as noted by Rafał Miłecki. Signed-off-by:
-
Alex Deucher authored
Useful for certain power management operations. You need to wait for the GUI engine (2D, 3D, CP, etc.) to be idle before changing clocks or adjusting engine parameters. (v2) Fix gui idle enable on pre-r6xx asics (v3) The gui idle interrrupt status bit is permanently asserted on pre-r6xx chips, but the interrrupt is still generated. workaround it in the driver. (v4) Add support for evergreen Signed-off-by:
-
Alex Deucher authored
Check to see if the GUI engine and related blocks (2D, 3D, CP, etc) are idle or not. There are a number of cases when we need to know if the drawing engine is busy. Signed-off-by:
-
Dave Airlie authored
Simple cloning rules compared to server: (a) single crtc (b) > 1 connector active (c) check command line mode (d) try and find 1024x768 DMT mode if no command line. (e) fail to clone Signed-off-by: -
Dave Airlie authored
After thinking it over a lot it made more sense for the core to deal with the output polling especially so it can notify X. v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings. v3: add config lock take inside polling, add intel/nouveau poll init/fini calls v4: config lock was a bit agressive, only needed around connector list reading. otherwise it could re-enter. glisse: discard drm_helper_hpd_irq_event v3: Reviewed-by: Michel Dänzer <michel@daenzer.net> Signed-off-by: -
Dan Carpenter authored
m == num_est3_modes is one past the end of the est3_modes[]. Signed-off-by:
Dan Carpenter <error27@gmail.com> Reviewed-by:
Adam Jackson <ajax@redhat.com> Signed-off-by:
-
Marcin Slusarz authored
let vga16fb claim 0xA0000+0x10000 region as its aperture; drm drivers don't use it, so we have to detect it and kick vga16fb manually - but only if drm is driving the primary card Signed-off-by:
Marcin Slusarz <marcin.slusarz@gmail.com> Cc: James Simmons <jsimmons@infradead.org> Cc: Dave Airlie <airlied@redhat.com> Cc: Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Marcin Slusarz authored
Currently vesafb/efifb/... is kicked when hardware driver is registering framebuffer. To do it hardware must be fully functional, so there's a short window between start of initialisation and framebuffer registration when two drivers touch the hardware. Unfortunately sometimes it breaks nouveau initialisation. Fix it by kicking firmware driver(s) before we start touching the hardware. Reported-by:
Didier Spaier <didier.spaier@epsm.fr> Tested-by:
-
Marcin Slusarz authored
It removes a hack from nouveau code which had to detect which region to pass to kick vesafb/efifb. Signed-off-by:
-
Kirill Smelkov authored
Recently I've studied my system dmesg and seen this: <lots of stuff before> 1 [ 0.478416] ACPI: Battery Slot [C1B4] (battery present) 2 [ 0.478648] ACPI: Battery Slot [C1B3] (battery absent) 3 [ 0.906678] [drm] initialized overlay support 4 [ 1.762304] Console: switching to colour frame buffer device 128x48 5 [ 1.765211] fb0: inteldrmfb frame buffer device 6 [ 1.765242] registered panic notifier 7 [ 1.765272] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 8 [ 1.765372] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <lots of stuff after> and it was not evident who registered that panic notifier on line 6. I'd bought it as some low-level stuff needed by kernel itself, but the time was inappropriate -- too late for such things. So I had to study sources to see it was drm who was registering switch-to-fb on panic. Let's avoid possible confusion and mark this message as going from drm subsystem. (I'm a bit unsure whether to use '[drm]:' or 'drm:' -- the rest of the kernel just uses 'topic:', and even in drm_fb_helper.c we use 'fb%d:' without [] brackets. Either way is ok with me.) Signed-off-by:
Kirill Smelkov <kirr@landau.phys.spbu.ru> Signed-off-by:
-
Jerome Glisse authored
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm crtc id. Bump the minor version so userspace can enable conditionaly features depend on this. V2 use num_crtc and avoid DRM_ERROR Signed-off-by:
Jerome Glisse <jglisse@redhat.com> Signed-off-by:
-
Adam Jackson authored
Having hsync both start and end on pixel 1072 ain't gonna work very well. Matches the X server's list. Signed-off-by:
Michael Tokarev <mjt@tls.msk.ru> Cc: stable@kernel.org Signed-off-by:
-
Julia Lawall authored
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Reviewed-by:
Corbin Simpson <MostAwesomeDude@gmail.com> Reviewed-by:
Matt Turner <mattst88@gmail.com> Signed-off-by:
-
