- 10 Mar, 2022 5 commits
-
-
Mukesh Sisodiya authored
Disable IMR region if it is enabled in the TLVs, but disabled at runtime by the FW. Signed-off-by:
Mukesh Sisodiya <mukesh.sisodiya@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20220304131517.2a696656a161.I99705472a8838121ffaca72977015dc2069549b9@changeidSigned-off-by:
-
Johannes Berg authored
There are no shipping firmware versions with this, and there will also not be in the future, so remove the support. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Ayala Barazani authored
The module param "enable_ini" is currently used to be enable/disable ini. Add the option to configure the FW debug preset via this module param, by change it type from boolean to an integer. Signed-off-by:
Ayala Barazani <ayala.barazani@intel.com> Signed-off-by:
-
Ayala Barazani authored
Add a flags bitfield in REDUCED_TX_POWER_CMD, and send it as is to FW. Signed-off-by:
-
Luca Coelho authored
Start supporting API version 71 for AX devices. Signed-off-by:
-
- 09 Mar, 2022 4 commits
-
-
Ping-Ke Shih authored
To work properly in 6G band, declare HE 6G capabilities. Without this fix, it can only TX/RX with OFDM rates. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220307012741.6371-1-pkshih@realtek.com
-
Johannes Berg authored
Bit 2 and 3 are reserved on 5/6 GHz and bit 1 is reserved on 2.4 GHz, so the driver should only set the non-reserved bits according to band. Signed-off-by:
-
Chin-Yen Lee authored
We found management frames get stuck when wifi chip enters low ps mode. So we add one notify wake function to trigger wifi chip into normal mode before forwarding management frames. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Po Hao Huang authored
Declare this function allows us to use customized scanning policy, so each scan takes less time. This is a similar implementation to hw_scan in rtw88, except that we offload more items to firmware and extend the maximum IE length. For backward compatibility, we fallback to sw_scan when firmware does not support this feature. Signed-off-by:
Po Hao Huang <phhuang@realtek.com> Signed-off-by:
-
- 25 Feb, 2022 3 commits
-
-
Ping-Ke Shih authored
Calculate the offset of center and primary frequencies to get hardware indices of center channel and primary channel, and then use them to configure hardware to a specific channel. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.18. Major changes: ath11k * debugfs interface to configure firmware debug log level * debugfs interface to test Target Wake Time (TWT) * provide 802.11ax High Efficiency (HE) data via radiotap ath9k * use hw_random API instead of directly dumping into random.c wcn36xx * fix wcn3660 to work on 5 GHz band
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 5.18 - bugfixes - mt7915 thermal management improvements - SAR support for more mt76 drivers - mt7986 wmac support on mt7915
-
- 24 Feb, 2022 24 commits
-
-
Felix Fietkau authored
When operating on a mix of DFS and non-DFS channels, the driver only checks the CAC status of the control channel. This causes beacons/tx to fail if the control channel is on a non-DFS channel. Fix this by calling cfg80211_reg_can_beacon to determine the DFS status of all affected channels Signed-off-by:Felix Fietkau <nbd@nbd.name>
-
Wan Jiabing authored
Fix following coccicheck warning: ./drivers/net/wireless/mediatek/mt76/mt7915/mac.c:768:29-31: WARNING !A || A && B is equivalent to !A || B Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Signed-off-by:
-
Lorenzo Bianconi authored
Similar to mt7915 driver, do not aggregate injected frames in HW A-MSDU block. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Nicolas Cavallari authored
By default, mt7915e does not enable thermal management until the default thermal zone does not reach a trip point. If the rest of the system have better cooling than the wireless hardware, then it is possible that the wireless chip can overheat while the rest of the system is fine. Signed-off-by:
Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Signed-off-by:
-
Nicolas Cavallari authored
The firmware-controlled actual throttle state was previously available by reading the cooling_device, but this confused the thermal subsystem. Add a hwmon attribute to get it instead. Signed-off-by:
-
Nicolas Cavallari authored
mt7915e registers a cooling_device with wrong semantics: 1. cooling_device expect that higher states values should cool more, but mt7915e did the opposite... with the exception of state == 0, which should "disable thermal management", but does not seem to have any effect since the previous state is kept. The result is that when the thermal zone heats up a bit and bumps the cooling_device state from 0 to 1 to cool a bit, the performance is destroyed, and when going back from 1 to 0, the performance stays bad. 2. Reading the cooling_device state does not always return the last written state, but can return the actual hardware throttle state, which is different. This is a problem because the mt7915 firmware actually implement the equivalent of a thermal zone with trip points. Setting the cooling device state actually changes the throttles at each trip point, so the following could occur if the first issue is fixed: - thermal subsystem set state to 100% power (state=0) - mt7915e driver set trip throttles to [100%, 50%, 25%, 12%] - hardware heats up and decides to switch to 50% power - thermal subsystem see that power is 50% (state=50), decide to increase it to 60% (state=40) because the rest of the system is cool. - mt7915e driver set trip throttle to [60%, 30%, 15%, 7%] - hardware thus switches to 30% power [race to the bottom continues...] This patch corrects the semantics of the cooling_device to the one that the thermal subsystem expect it. Signed-off-by:
-
Felix Fietkau authored
Instead of just taking the maximum per-chain signal strength values, add an approximation for the sum of the combined signal. This should more accurately reflect the real signal strength, especially if the per-chain signal strength values are close to each other Signed-off-by: -
Changcheng Deng authored
Use min_t() in order to make code cleaner. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
MeiChia Chiu authored
The muru enable/disable are only set after the first station connection. Without this patch, the firmware couldn't enable muru if the first connected station is non-HE type. Fixes: 16bff457 ("mt76: mt7915: rework mt7915_mcu_sta_muru_tlv()") Reviewed-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
MeiChia Chiu <meichia.chiu@mediatek.com> Signed-off-by:
-
Ryder Lee authored
Add missing band idx check for DBDC cases. Signed-off-by:
-
Yang Li authored
Smatch reports the following: drivers/net/wireless/mediatek/mt76/mt7615/mac.c:1865 mt7615_mac_adjust_sensitivity() warn: assigning (-110) to unsigned variable 'def_th' drivers/net/wireless/mediatek/mt76/mt7615/mac.c:1865 mt7615_mac_adjust_sensitivity() warn: assigning (-98) to unsigned variable 'def_th' Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Signed-off-by:
-
Chad Monroe authored
Newer chips such as MT7915 require up to 16-bits for this field. Fixes: 49126ac1 ("mt76: connac: move mt76_connac_mcu_bss_basic_tlv in connac module") Signed-off-by:
Chad Monroe <chad.monroe@smartrg.com> Acked-by:
-
Lorenzo Bianconi authored
Fix the following sparse warning in mt7915_mac_tx_free routine: warning: incorrect type in assignment (different base types) expected unsigned int [usertype] *cur_info got restricted __le32 * warning: cast to restricted __le32 Fixes: c17780e7 ("mt76: mt7915: add txfree event v3") Signed-off-by:
-
Lorenzo Bianconi authored
Fix the following sparse warnings: warning: incorrect type in initializer (different base types) expected restricted __le16 [usertype] msg_type got int warning: incorrect type in assignment (different base types) expected restricted __le32 [usertype] timestamp got unsigned int Fixes: 988845c9 ("mt76: mt7915: add support for passing chip/firmware debug data to user space") Signed-off-by:
-
Deren Wu authored
The following error is see from the compiler: mt7615/debugfs.c: In function ‘mt7615_ext_mac_addr_read’: mt7615/debugfs.c:465:1: warning: the frame size of 1072 bytes is larger than 1024 bytes [-Wframe-larger-than=] The issue is due to allocating a buffer as string storage. Fix by converting to a dynamical allocation of the buffer. Reviewed-by:Deren Wu <deren.wu@mediatek.com> Signed-off-by:
-
Peter Chiu authored
Initialize smps mode to prevent firmware rate adaptation issue. Reviewed-by:
Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by:
-
Bo Jiao authored
The wfsys of MT7986 has only single adie chip for non-dbdc devices, and it binds to band1 by default. Hence this patch adds band_idx to explicitly configure phy accordingly. Co-developed-by:
Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by:
Shayne Chen <shayne.chen@mediatek.com> Signed-off-by:
Bo Jiao <Bo.Jiao@mediatek.com> Reviewed-by:
-
Bo Jiao authored
This adds MT7986 SoC integrated multi-band 4x4 WiFi 6/6E. Co-developed-by:
-
Francesco Magliocca authored
Reading through the commit history, it looks like there is no special need why we must skip the first 4 bytes in this trace call: trace_ath10k_htt_rx_desc(ar, (void*)rx_desc + sizeof(u32), hw->rx_desc_ops->rx_desc_size - sizeof(u32)); found in the function ath10k_htt_rx_amsdu_pop in the file htt_rx.c i think the original author (who is also the one who added rx_desc tracing capabilities in a0883cf7) just wanted to trace the rx_desc contents, ignoring the fw_rx_desc_base info field (which is the part being skipped over). But the trace_ath10k_htt_rx_desc later added don't care about skipping it, so it may be good to uniform this call to the others in the file. But this would change the output of the trace and thus it may be a problem for tools that rely on it. Therefore I propose until further discussion to just keep it as it is and just fix the pointer arithmetic bug. Add missing void* cast to rx descriptor pointer in order to properly skip the initial 4 bytes of the rx descriptor when passing it to trace_ath10k_htt_rx_desc trace function. This fixes the pointer arithmetic error detected by Dan Carpenter's static analysis tool. Fixes: 6bae9de6 ("ath10k: abstract htt_rx_desc structure") Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1 Signed-off-by:
Francesco Magliocca <franciman12@gmail.com> Link: https://lore.kernel.org/ath10k/20220201130900.GD22458@kili/Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220221122638.7971-1-franciman12@gmail.com
-
Gustavo A. R. Silva authored
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Kees Cook <keescook@chromium.org> Acked-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Venkateswara Naralasetty authored
Target copies spectral report and CFR report through dbring to host for further processing. This mechanism involves ring and buffer management in the Host, FW, and uCode, where improper tail pointer update issues are seen. This dbring debug support help to debug such issues by tracking head and tail pointer movement along with the timestamp at which each buffer is received and replenished. Provide a debugfs interface to enalbe/disable dbring debug support and dump the dbring debug entries. Also introduced a new hardware param to add dbring debugfs support for few hardwares which are using dbings. Usage: echo <dbr_id> <val> > /sys/kernel/debug/ath11k/ipq8074_2/ mac0/enable_dbr_debug dbr_id: 0 for spectral and 1 for CFR val: 0 - disable, 1 - enable. Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Venkateswara Naralasetty <quic_vnaralas@quicinc.com> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Translate HE status to radiotap format. This uses HE radiotap definitions from include/net/ieee80211_radiotap.h. Co-developed-by:
Miles Hu <milehu@codeaurora.org> Signed-off-by:
Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Add new bitmasks and macro definitions required for parsing HE status tlvs. Decode HE status tlvs, which will used in dumping ppdu stats as well as updating radiotap headers. Co-developed-by:
-
Pradeep Kumar Chitrapu authored
This allows us to pass HE rates down into the stack. Co-developed-by:
John Crispin <john@phrozen.org> Signed-off-by:
-
- 23 Feb, 2022 4 commits
-
-
Peter Chiu authored
Add an entry for MT7986 SoC. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Deren Wu authored
For non-mmio devices, should set fc values to proper txwi config Fixes: 48fab5bb ("mt76: mt7921: introduce mt7921s support") Tested-by:
Sean Wang <sean.wang@mediatek.com> Co-developed-by:
Leon Yen <Leon.Yen@mediatek.com> Signed-off-by:
-
Shayne Chen authored
Free the skb of fw monitor packets. Signed-off-by:
-
Bo Jiao authored
Fix channel state update error issue due to wrong register access for mt7916. Signed-off-by:
-
