- 15 Sep, 2014 38 commits
-
-
Roy Spliet authored
V2: Always disable DLL reset Signed-off-by:
Roy Spliet <rspliet@eclipso.eu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com>
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Time measured from disabling FB to re-enabling, PPWR_IN reveals status of heads at the end of script. Helps debug various issues (like flicker). Signed-off-by:
-
Roy Spliet authored
Needs to be done after wait-for-VBLANK, and NVA3 requires register writes in between. Rather than hard-coding register writes, just split out fb_disable and fb_enable. v2. Squashed "fb/ramnve0: disable fb before reclocking" Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Martin Peres authored
Signed-off-by:
Martin Peres <martin.peres@free.fr> Signed-off-by:
-
Martin Peres authored
One of my nv92 has a calibrated internal sensor but it displays 0°C as the default values use sw calibration values to force the temperature to 0. Since we cannot read the temperature from the adt7473 present on this board, let's re-enable the internal reading! Signed-off-by:
-
Martin Peres authored
We will use this subdev to disable temperature reading on cards that did not get a sensor calibration in the factory. v2: - rename "nouveau_fuse_rd32" to "gxXXX_fuse_rd32" as adviced by Christian Costa - fold the code a little as adviced by Emil Velikov Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Roy Spliet authored
Signed-off-by:
-
Pierre Moreau authored
Signed-off-by:
Pierre Moreau <pierre.morrow@free.fr> Signed-off-by:
-
Pierre Moreau authored
It can help to remove any ambiguity about which options were passed to Nouveau, especially in case the user had some options set in /etc/modprobe.d/*.conf that he forgot about, as they won't appear in a dmesg. Signed-off-by:
-
Ben Skeggs authored
Signed-off-by: -
Martin Peres authored
Signed-off-by: -
Martin Peres authored
Signed-off-by:
-
Martin Peres authored
Signed-off-by:
-
Martin Peres authored
Signed-off-by:
-
Martin Peres authored
The problem with the current implementation is that adding a timer improperly checked which process would time up first by not taking into account how much time elapsed since their timer got scheduled. Rework the re-scheduling decision t fix this. The catch with this fix is that we are limited to scheduling timers of up to 2^31 ticks to avoid any potential overflow. Since we are unlikely to need to wait for more than a second, this won't be a problem :) Another possible fix would be to decrement the timeouts of all processes but it would duplicate a lot of code and dealing with edge cases wasn't pretty last time I checked. Signed-off-by:
-
Martin Peres authored
For some reason, it is now required to wait a 20 µs after the 0x200 reset of the engine. Signed-off-by:
-
Martin Peres authored
v2: change the copyright ownership from "Nouveau Community" to myself, as per Illia's recommendation. Signed-off-by:
-
Martin Peres authored
Signed-off-by:
-
Martin Peres authored
Re-use the therm-exported fan structure with only two minor modifications: - pwm_freq: u16 -> u32; - add fan_type (toggle or PWM) v2: - Do not memset the table to 0 as it erases the pre-set default values Signed-off-by:
-
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
The allocation algorithm doesn't expect there to be holes in the mm, which causes its alignment/cutoff calculations to choke (and go negative) when encountering the last chunk of a block before a hole. The least expensive solution is to simply fill in any holes with nodes that are pre-marked as being allocated. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
This is really the wrong thing to do, but at the time it was our only option to prevent worse issues. We no longer cause quite so much anger from LTC, so it's not needed. Signed-off-by: -
Ben Skeggs authored
Signed-off-by: -
Ben Skeggs authored
The event source types/index might need to be derived from it. Signed-off-by: -
Ben Skeggs authored
Signed-off-by:
-
- 12 Sep, 2014 2 commits
-
-
Dave Airlie authored
Merge tag 'topic/drm-header-rework-2014-09-12' of git://anongit.freedesktop.org/drm-intel into drm-next So here's the header cleanup, rebased on top of drm-next. Two new header files are created here: - drivers/gpu/drm/drm_internal.h for non-legacy drm.ko private declarations. - include/drm/drm_legacy.h for legacy interfaces used by non-kms drivers. And of course lots fo stuff gets shuffled into the already existing drivers/gpu/drm/drm_legacy.h for drm.ko internal stuff. topic branch smoke-tested in drm-intel-nightly for a bit. And the 0day tester also worked through it (and found a few places I didn't add a static to functions). * tag 'topic/drm-header-rework-2014-09-12' of git://anongit.freedesktop.org/drm-intel: drm: Move DRM_MAGIC_HASH_ORDER into drm_drv.c drm: Move drm_class to drm_internal.h drm: Move LOCK_TEST_WITH_RETURN to <drm/drm_legacy.h> drm: Move legacy buffer structures to <drm/drm_legacy.h> drm: Move drm_memory.c map support declarations to <drm/drm_legacy.h> drm: Purge ioctl forward declarations from drmP.h drm: unexport drm_global_mutex drm: Move piles of functions from drmP.h to drm_internal.h drm: Move vblank related module options into drm_irq.c drm: Drop drm_sysfs_class from drmP.h drm: Move __drm_pci_free to drm_legacy.h drm: Create drm legacy driver header drm: Move drm_legacy_vma_flush into drm_legacy.h drm: Move sg functions into drm_legacy.h drm: Move dma functions into drm_legacy.h
-
Daniel Vetter authored
Only used in one place ever, so put it right next to that. Signed-off-by:Daniel Vetter <daniel.vetter@ffwll.ch>
-
