Simon Horman says:

====================
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this short series is to provide GSO in software for MPLS packets
whose skbs are GSO.

Change since v4:

Update first patch of the series to use 16 bits for all *_headers
rather than just inner_*_headers

Simon Horman (2):
  net: Use 16bits for *_headers fields of struct skbuff
  MPLS: Add limited GSO support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.

The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.

SKB Usage:

When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:

* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
  skb->inner_protocol is added by this patch.

* Set skb->protocol to the new MPLS ethertype of the packet.

* Set skb->network_header to correspond to the
  end of the L3 header, including the MPLS label stack.

I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code.  The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.

Features:

I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols.  Jesse, I understand that
you have some ideas here.  I am more than happy to change my implementation.

This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.

A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload.  Currently no devices support this
and MPLS GSO always falls back to software.

Alternate Implementation:

One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().

I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.

MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.

Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to mitigate ongoing incresase in the size of struct skbuff
use 16 bit integer offsets rather than pointers for inner_*_headers.

This appears to reduce the size of struct skbuff from 0xd0 to 0xc0
bytes on x86_64 with the following all unset.

	CONFIG_XFRM
	CONFIG_NF_CONNTRACK
	CONFIG_NF_CONNTRACK_MODULE
	NET_SKBUFF_NF_DEFRAG_NEEDED
	CONFIG_BRIDGE_NETFILTER
	CONFIG_NET_SCHED
	CONFIG_IPV6_NDISC_NODETYPE
	CONFIG_NET_DMA
	CONFIG_NETWORK_SECMARK
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a comment which explains the real meaning of XCVR_INTERNAL (PHY and
Ethernet MAC in the same package/die) and XCVR_EXTERNAL (PHY and
Ethernet MAC in a different package/die). Most if not all of the drivers
setting their transceiver type already do it the way the comment
describes it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fabio Estevam says:

====================
This series provides support for controlling the PHY regulator in suspend/resume.

Fabio Estevam (5):
  fec: Place the phy regulator in the private structure
  fec: Invert the order of error path sequence
  fec: Disable the PHY regulator on error and removal
  fec: Remove irqs first
  fec: Handle the regulator in suspend/resume
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to save power, let's disable the regulator in the suspend function and
enable it in resume.

Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During probe the clocks are enabled prior than the acquiring the interrupts.

In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case of error during probe, disable the PHY regulator.

Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.

This is wrong because at this point the interrupts have not even been acquired.

Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.

This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the PCI shutdown callback to support un-orderly shutdown, i.e.,
shutdowns in which the remove callback will not be called.

Due to the lack of this functionality, when an un-orderly shutdown occurred,
it was possible for wake-on-lan to remain disabled.

This is now fixed as the callback introduces the correct place in which
`system_state' can be queried and wake-on-lan be configured accordingly.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0eb43b4b
"bnx2x, bnx2fc: Use per port max exchange resources" has changed the number
of available FCoE exchanges, even in scenarios when some of the functions has
no FCoE support; This needlessly degraded the available resources.

Remedy this by calculating the maximal number of functions that may actually
utilize said connection.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A PF should ack the firmware when receiving unknown messages through the VF's
mailbox. This prevents the VF mailbox from being stuck in case of a VF sending
a message unknown to the PF (e.g. VF with more advanced version).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the print of the PCI gen3 link speed (8GHz), as well as correcting
the same print for 57712 boards (the print erroneously showed a 2.5GHz speed).
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hypervisor/Supervisor should set the VF's MAC prior to its load;
Using a randomly generated MAC as a default is a bad practice.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

case TCP_FIN_WAIT1 can also be simplified by reversing tests
and adding breaks;

Add braces after case and move automatic definitions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

case TCP_SYN_RECV: can have another indentation level removed
by converting

	if (acceptable) {
		...;
	} else {
		return 1;
	}

to
	if (!acceptable)
		return 1;
	...;

Reflow code and comments to fit 80 columns.

Another pure cleanup patch.
Signed-off-by: Joe Perches <joe@perches.com>
Improved-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove one level of indentation 'introduced' in commit
c3ae62af (tcp: should drop incoming frames without ACK flag set)

if (true) {
        ...
}

@acceptable variable is a boolean.

This patch is a pure cleanup.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now when upper device is changed, event is not propagated via RT Netlink
to userspace. Userspace might never now about the change. Fix this by
adding upper-device-change notifier event.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.

Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.

Caveats:

- Setting options via ancillary data (e.g., using IPV6_PKTINFO
  to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
  everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
  properly.

Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
This patch series includes following changes:
* Support for spoof check configuration per VF using
  iproute2 tool.
* Set HW mask for 8300 adapter in INT-x mode to stop generating
  interrupts.
* Updated IRQ name for 8200 and 8300 Series adapter as per
  format used by other multiqueue drivers.
* Remove qlcnic_config_npars module parameter.
* Initialize trans_work and idc_aen_work at VF probe.
* Convert netsted if-else into switch-case statement.
* Change in diagnostics routine.
* Modify reset recovery path in diag mode by providing diagnostics
  routines enough time to unwind before proceeding with reset recovery.
* Implement GET_LED_STATUS command for 82xx adapter and refactor
  qlcnic_store_beacon() to split 8200 and 8300 specific calls.
* Some cleanup and log enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o GET_LED_STATUS command will be used by driver to get
  current beacon state from 82xx adapter.
o Refactored qlcnic_store_beacon() to split 8200 and 8300
  specific calls.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide diagnostics routines enough time to unwind before
proceeding with reset recovery.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test and set diagnostics mode bit before starting
diagnostics tests. Stop diagnostics tests if adapter is resetting.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o work_struct should be initialized before cancel_delayed_work
  call to destroy it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>