- 05 Dec, 2009 40 commits
-
-
Rafal Milecki authored
Signed-off-by:
Rafal Milecki <zajec5@gmail.com> Signed-off-by:
Jean-Francois Moine <moinejf@free.fr> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-Francois Moine authored
Signed-off-by:
-
Jean-Francois Moine authored
Signed-off-by:
-
Michael Krufky authored
Display i2c adapter id, address and master / slave role in debug output. Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32. Convert tda18271_priv.tm_rfcal from unsigned int to u8. Cast subtractions between u32 values as s32. Signed-off-by:
-
Michael Krufky authored
Use temporary variables for signed calulations between unsigned values Signed-off-by:
-
Henk Vergonet authored
This adds a forgotten module_param macro needed to set a deemphasis of 50us. It is the standard setting for commercial FM radio broadcasts outside the US. Signed-off-by:
Henk Vergonet <Henk.Vergonet@gmail.com> Signed-off-by:
-
Michael Krufky authored
Allow dvb-usb adapter drivers to specify a fe_ioctl_override callback to enable device-specific handling of DVB frontend operations. Signed-off-by:
-
Michael Krufky authored
override set_frontend to allow rf input path switching on the HVR1275 Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Andy Walls authored
This changes adds IR Rx keypress input event handling to the CX23885 module. This change specifically only adds input handling for IR devices implemented as v4l2_subdevices, using only the pulse width mode (for now), and only with RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6 mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote and HVR-1850 IR receiver work now. Signed-off-by:
Andy Walls <awalls@radix.net> Signed-off-by:
-
Andy Walls authored
Signed-off-by:
-
Andy Walls authored
Add integrated IR subdevice interrupt and notification handling. This is in preparation of input keypress handling changes for the cx23885 module. Signed-off-by:
-
Andy Walls authored
This change completes the v4l2_subdev implementation for IR receive for the IR controller built into the CX23888. This changes almost completes the IR transmit side also, but doesn't. Instead notes in the comments describe what needs to be done for IR Tx to work in the subdevice implementation. The current Tx behavior is skeletal and benign. If left alone, it does nothing. It will only ever generate a Tx interrupt on Tx init by a caller or when the tx_write() method is called. The ISR, when called, will then disable the Tx FIFO service interrupt. Signed-off-by:
-
Andy Walls authored
Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device. This change is specifically needed at this time to support the integrated IR controller in the CX2388[58] chips. Signed-off-by:
-
Steven Toth authored
The prior mechanism wasn't reliable with the cx23887. This new mechanism tests correctly against cx23885, 7 and 8 based products. Signed-off-by:
Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Andy Walls authored
For the IR controller on the CX23888 to work for the HVR-1850 and in general, the A/V core must be initialized to get the VID_CLK going. The VID_CLK is the timing reference for the CX23888's integrated IR controller. Signed-off-by:
-
Andy Walls authored
The SYS and AUX PLLs need to be initialized to different values based on the chip: CX23885, CX23887, CX23888, as each uses a different crystal frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz. Signed-off-by:
-
Andy Walls authored
Separate out the set_audclk_freq() function into separate functions for the four families of cores. These cores all use slightly different sample clock schemes and may be assuming slightly (+/- 3 Hz) different reference frequencies. The code resuse was not worth the maintenance and testing headache of have all chips use the same function peppered with conditional logic. Added comments on how PLL and SRC parameters values are computed. Fixed a few bugs related to the shared code having a large number of conditional statements. Noted inconsistencies with FIXME in the comments. This is done in preparation for getting the CX2388[578] PLL/clock setting logic cleaned up for CX23888 analog video and IR (which need the VID PLL set right). Signed-off-by:
-
Andy Walls authored
Change logic to check for various chip or core families to inline functions. Checks for specific chips should be made against the state->id field now. This is in preparation for chip/core specific code for setting up PLLs for the CX2388[578] family of cores, that all run with different crystal frequencies. Signed-off-by:
-
Andy Walls authored
Add improved logic to detect the exact CX2388[578] A/V core that is being probed. Also cleaned up detection and logging for CX2310[12], CX2583[67], and CX2584[0123] cores and chips. Also added code to identify a CX2388[578] A/V decoder core that is not responding properly. Typical symptoms include registers 0x00-0xff responding properly but all other registers returning the same value (0x13 and 0x5 have been observed). This state will cause proper detection of '885 vs. '887 vs. '888 to fail and the chip won't respond to get configured properly anyway. I have no method of reseting the core to a working state at this time; but I didn't try too hard to work one out either. The problem likely only occurs in development. I suspect configuring the SYS PLL VCO to oscillate too slowly (286.3 MHz?) before post divide may be the root cause, when encountered. Signed-off-by:
-
Andy Walls authored
This change adds a skeletal implementation of a v4l2_subdevice to provide encapsulation and abstraction of the CX23888's integrated consumer infrared controller. This change also instantiates the cx23888_ir subdev for the HVR-1850 which has IR hardware physically wired up to a CX23888. The cx23888_ir subdev code is being written with long-term objectives to: 1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx IR controllers 2. possibly port it to the cx18 module for the CX23418 IR controller 3. have the IR subdevice accessed abstractly in the cx23885 module, so the driver can ignore the difference between the CX23885 and CX23888. Signed-off-by:
-
Andy Walls authored
This changes corrects the ioctl() operations for both the CX2388[578] analog video and MPEG video device nodes to properly and consistently support VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s. This caused some ioctl() support routines to be broken out into a separate source file. Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers including the CX2388[57] functions handled by the cx25840 module. This was done in anticipation of developing a new v4l2_subdev for the integrated IR controller of the CX23888. Signed-off-by:
-
Andy Walls authored
Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated A/V decoders cores, integrated IR controller core, and the CX23417 MPEG encoder. The cx23885 module and cx25840 module will use these identifiers in upcoming changes. Signed-off-by:
-
Devin Heitmueller authored
The board support has been validated by the user, so get rid of the warning that shows up on board load. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Dmitri's patch for the Behold X7 didn't use the #define I had setup for XC5000_RADIO_FM1, so cut over to using that instead of "1". Signed-off-by:
-
Beholder Intl. Ltd. Dmitry Belimov authored
Add support for the digital side of the Behold X7 Signed-off-by:
Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Uroš Vampl authored
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid XS (em2882). Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing and testing pretty much the exact same patch as provided by Uros. Between the two of them, they got all the core functionality working for the device. Cc: Andrej Suligoi <suligoi@gmail.com> Signed-off-by:
Uroš Vampl <mobile.leecher@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
Seems that the reference design used for the KWorld 2800d switched from the em2860 to em2862, so we need to add the new USB id (and the i2c hash remains so all we need is the default em2862 id. Thanks to Ian Young for reporting the issue and testing the fix. Cc: Ian Young <ian@duffrecords.com> Signed-off-by:
-
Devin Heitmueller authored
Remove hard-coded definition of the xc5000 FM radio input, making it a parameter passed in when doing the attach call. Signed-off-by:
-
Beholder Intl. Ltd. Dmitry Belimov authored
Add FM radio for the xc5000 silicon tuner chip. Signed-off-by:
-
David Ellingsworth authored
Set radio frequency only upon success. Signed-off-by:
David Ellingsworth <david@identd.dyndns.org> Acked-by:
Alexey Klimov <klimov.linux@gmail.com> Signed-off-by:
Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by:
-
David Ellingsworth authored
Simplify device warnings. Signed-off-by:
-
David Ellingsworth authored
Preserve radio state during suspend/resume. Signed-off-by:
-
David Ellingsworth authored
Fix behavior of set_stereo function. Signed-off-by:
-
David Ellingsworth authored
Ensure the radio is initialized to a consistent state. Signed-off-by:
-
David Ellingsworth authored
Remove device initialization from open/close. Signed-off-by:
-
David Ellingsworth authored
Fix portential use after free. Signed-off-by:
-
David Ellingsworth authored
Remove device removed indicator Signed-off-by:
-
David Ellingsworth authored
Simplify locking in ioctl callbacks. Signed-off-by:
-
