- 31 Jul, 2017 40 commits
-
-
Eric Anholt authored
[ Upstream commit fedf266f ] The bcm_kona_wdt_set_resolution_reg() call takes the spinlock, so initialize it earlier. Fixes a warning at boot with lock debugging enabled. Fixes: 6adb730d ("watchdog: bcm281xx: Watchdog Driver") Signed-off-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
Wim Van Sebroeck <wim@iguana.be> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
Dan Carpenter authored
[ Upstream commit 1e3d0c2c ] There are some missing error codes here so we accidentally return NULL instead of an error pointer. It results in a NULL pointer dereference. Fixes: df71837d ("[LSM-IPSec]: Security association restriction.") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit e747f643 ] The default error code in pfkey_msg2xfrm_state() is -ENOBUFS. We added a new call to security_xfrm_state_alloc() which sets "err" to zero so there several places where we can return ERR_PTR(0) if kmalloc() fails. The caller is expecting error pointers so it leads to a NULL dereference. Fixes: df71837d ("[LSM-IPSec]: Security association restriction.") Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 9b3eb541 ] When CONFIG_XFRM_SUB_POLICY=y, xfrm_dst stores a copy of the flowi for that dst. Unfortunately, the code that allocates and fills this copy doesn't care about what type of flowi (flowi, flowi4, flowi6) gets passed. In multiple code paths (from raw_sendmsg, from TCP when replying to a FIN, in vxlan, geneve, and gre), the flowi that gets passed to xfrm is actually an on-stack flowi4, so we end up reading stuff from the stack past the end of the flowi4 struct. Since xfrm_dst->origin isn't used anywhere following commit ca116922 ("xfrm: Eliminate "fl" and "pol" args to xfrm_bundle_ok()."), just get rid of it. xfrm_dst->partner isn't used either, so get rid of that too. Fixes: 9d6ec938 ("ipv4: Use flowi4 in public route lookup interfaces.") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
Gleb Fotengauer-Malinovskiy authored
[ Upstream commit 7292ae3d ] The latest change of asm goto support check added passing of KBUILD_CFLAGS to compiler. When these flags reference gcc plugins that are not built yet, the check fails. When one runs "make bzImage" followed by "make modules", the kernel is always built with HAVE_JUMP_LABEL disabled, while the modules are built depending on CONFIG_JUMP_LABEL. If HAVE_JUMP_LABEL macro happens to be different, modules are built with undefined references, e.g.: ERROR: "static_key_slow_inc" [net/netfilter/xt_TEE.ko] undefined! ERROR: "static_key_slow_dec" [net/netfilter/xt_TEE.ko] undefined! ERROR: "static_key_slow_dec" [net/netfilter/nft_meta.ko] undefined! ERROR: "static_key_slow_inc" [net/netfilter/nft_meta.ko] undefined! ERROR: "nf_hooks_needed" [net/netfilter/ipvs/ip_vs.ko] undefined! ERROR: "nf_hooks_needed" [net/ipv6/ipv6.ko] undefined! ERROR: "static_key_count" [net/ipv6/ipv6.ko] undefined! ERROR: "static_key_slow_inc" [net/ipv6/ipv6.ko] undefined! This change moves the check before all these references are added to KBUILD_CFLAGS. This is correct because subsequent KBUILD_CFLAGS modifications are not relevant to this check. Reported-by:
Anton V. Boyarshinov <boyarsh@altlinux.org> Fixes: 35f860f9 ("jump label: pass kbuild_cflags when checking for asm goto support") Cc: stable@vger.kernel.org # v4.10 Signed-off-by:
Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org> Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by:
David Lin <dtwlin@google.com> Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 912964ea ] Commit 6f29a130 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc") invoked sctp_verify_addr to verify the addr. But it didn't check af variable beforehand, once users pass an address with family = 0 through sockopt, sctp_get_af_specific will return NULL and NULL pointer dereference will be caused by af->sockaddr_len. This patch is to fix it by returning NULL if af variable is NULL. Fixes: 6f29a130 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jack Morgenstein authored
[ Upstream commit 9577b174 ] When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's message log when (correct, normally operating) apps use SRQ LIMIT events as a trigger to post WQEs to SRQs. Add more information to the existing debug printout for SRQ_LIMIT, and output the warning messages only for the SRQ CATAS ERROR event. Fixes: acba2420 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs") Fixes: e0debf9c ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Ivan Vecera authored
[ Upstream commit fe68d8bf ] Return value from be_mcc_notify_wait() contains a base completion status together with an additional status. The base_status() macro need to be used to access base status. Fixes: e3a7ae2c be2net: Changing MAC Address of a VF was broken Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
Ivan Vecera <cera@cera.cz> Signed-off-by:
-
Heiko Carstens authored
[ Upstream commit e991c24d ] We have quite a lot of code that depends on the order of the __ctl_load inline assemby and subsequent memory accesses, like e.g. disabling lowcore protection and the writing to lowcore. Since the __ctl_load macro does not have memory barrier semantics, nor any other dependencies the compiler is, theoretically, free to shuffle code around. Or in other words: storing to lowcore could happen before lowcore protection is disabled. In order to avoid this class of potential bugs simply add a full memory barrier to the __ctl_load macro. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Nikita Yushchenko authored
[ Upstream commit 602d9858 ] Some drivers do depend on page mappings to be page aligned. Swiotlb already enforces such alignment for mappings greater than page, extend that to page-sized mappings as well. Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine assumes page-aligned mappings. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Konrad Rzeszutek Wilk <konrad@kernel.org> Signed-off-by:
-
Dave Kleikamp authored
[ Upstream commit 4d22c75d ] If the last section of a core file ends with an unmapped or zero page, the size of the file does not correspond with the last dump_skip() call. gdb complains that the file is truncated and can be confusing to users. After all of the vma sections are written, make sure that the file size is no smaller than the current file position. This problem can be demonstrated with gdb's bigcore testcase on the sparc architecture. Signed-off-by:
Dave Kleikamp <dave.kleikamp@oracle.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Tobias Klauser authored
[ Upstream commit 45382862 ] info->si_addr is of type void __user *, so it should be compared against something from the same address space. This fixes the following sparse error: arch/x86/mm/mpx.c:296:27: error: incompatible types in comparison expression (different address spaces) Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Felix Fietkau authored
[ Upstream commit 43071d8f ] ibss and mesh modes copy the ht capabilites from the band without overriding the SMPS state. Unfortunately the default value 0 for the SMPS field means static SMPS instead of disabled. This results in HT ibss and mesh setups using only single-stream rates, even though SMPS is not supposed to be active. Initialize SMPS to disabled for all bands on ieee80211_hw_register to ensure that the value is sane where it is not overriden with the real SMPS state. Reported-by:
Elektra Wagenrad <onelektra@gmx.net> Signed-off-by:
Felix Fietkau <nbd@nbd.name> [move VHT TODO comment to a better place] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Kevin Hilman authored
[ Upstream commit c5a2a394 ] The correct error checking for dma_map_single() is to use dma_mapping_error(). Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Roberto Sassu authored
[ Upstream commit cd60be49 ] Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset() attempts to free the memory again. Signed-off-by:
Roberto Sassu <rsassu@suse.de> Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Acked-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Brendan McGrath authored
[ Upstream commit a89af4ab ] Support for the Asus Touchpad was recently added. It turns out this device can fail initialisation (and become unusable) when the RESET command is sent too soon after the POWER ON command. Unfortunately the i2c-hid specification does not specify the need for a delay between these two commands. But it was discovered the Windows driver has a 1ms delay. As a result, this patch modifies the i2c-hid module to add a sleep inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms. See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further details. Signed-off-by:
Brendan McGrath <redmcg@redmandi.dyndns.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Jiri Slaby authored
[ Upstream commit ff7a28a0 ] When a system panics, the "Rebooting in X seconds.." message is never printed because it lacks a new line. Fix it. Link: http://lkml.kernel.org/r/20170119114751.2724-1-jslaby@suse.czSigned-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Balakrishnan Raman authored
[ Upstream commit efb5f68f ] Mac aging is applicable only for dynamically learnt remote mac entries. Check for user configured static remote mac entries and skip aging. Signed-off-by:
Balakrishnan Raman <ramanb@cumulusnetworks.com> Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Michael S. Tsirkin authored
[ Upstream commit d0fa28f0 ] I don't have any guests with PAGE_SIZE > 64k but the code seems to be clearly broken in that case as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need more than 8 bit and so the code in mergeable_ctx_to_buf_address does not give us the actual true size. Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 4078b76c ] We need to check the return value of phy_connect_direct() in dsa_slave_phy_connect() otherwise we may be continuing the initialization of a slave network device with a PHY that already attached somewhere else and which will soon be in error because the PHY device is in error. The conditions for such an error to occur are that we have a port of our switch that is not disabled, and has the same port number as a PHY address (say both 5) that can be probed using the DSA slave MII bus. We end-up having this slave network device find a PHY at the same address as our port number, and we try to attach to it. A slave network (e.g: port 0) has already attached to our PHY device, and we try to re-attach it with a different network device, but since we ignore the error we would end-up initializating incorrect device references by the time the slave network interface is opened. The code has been (re)organized several times, making it hard to provide an exact Fixes tag, this is a bugfix nonetheless. Signed-off-by:
-
Lendacky, Thomas authored
[ Upstream commit 738f7f64 ] The xgbe_init() routine returns a return code indicating success or failure, but the return code is not checked. Add code to xgbe_init() to issue a message when failures are seen and add code to check the xgbe_init() return code. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
Zach Ploskey authored
[ Upstream commit cfee5d63 ] On Ideapad laptops, ACPI event 1 is currently not handled. Many models log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while running on battery power. Some convertible laptops receive this event when switching in and out of tablet mode. This adds and additional case for event 1 in ideapad_acpi_notify to call ideapad_input_report(priv, vpc_bit), so that the event is reported to userspace and we avoid unnecessary logging. Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481) Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751) Signed-off-by:
Zach Ploskey <zach@ploskey.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Eric Farman authored
[ Upstream commit 773c7220 ] In the case of a graceful set of detaches, where the virtio-scsi-ccw disk is removed from the guest prior to the controller, the guest behaves quite normally. Specifically, the detach gets us into sd_sync_cache to issue a Synchronize Cache(10) command, which immediately fails (and is retried a couple of times) because the device has been removed. Later, the removal of the controller sees two CRWs presented, but there's no further indication of the removal from the guest viewpoint. [ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2 [ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0 However, on s390, the SCSI disks can be removed "by surprise" when an entire controller (host) is removed and all associated disks are removed via the loop in scsi_forget_host. The same call to sd_sync_cache is made, but because the controller has already been removed, the Synchronize Cache(10) command is neither issued (and then failed) nor rejected. That the I/O isn't returned means the guest cannot have other devices added nor removed, and other tasks (such as shutdown or reboot) issued by the guest will not complete either. The virtio ring has already been marked as broken (via virtio_break_device in virtio_ccw_remove), but we still attempt to queue the command only to have it remain there. The calling sequence provides a bit of distinction for us: virtscsi_queuecommand() -> virtscsi_kick_cmd() -> virtscsi_add_cmd() -> virtqueue_add_sgs() -> virtqueue_add() if success return 0 elseif vq->broken or vring_mapping_error() return -EIO else return -ENOSPC A return of ENOSPC is generally a temporary condition, so returning "host busy" from virtscsi_queuecommand makes sense here, to have it redriven in a moment or two. But the EIO return code is more of a permanent error and so it would be wise to return the I/O itself and allow the calling thread to finish gracefully. The result is these four kernel messages in the guest (the fourth one does not occur prior to this patch): [ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2 [ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0 [ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK I opted to fill in the same response data that is returned from the more graceful device detach, where the disk device is removed prior to the controller device. Signed-off-by:
Eric Farman <farman@linux.vnet.ibm.com> Reviewed-by:
Fam Zheng <famz@redhat.com> Signed-off-by:
-
Vineeth Remanan Pillai authored
[ Upstream commit 90c311b0 ] During an OOM scenario, request slots could not be created as skb allocation fails. So the netback cannot pass in packets and netfront wrongly assumes that there is no more work to be done and it disables polling. This causes Rx to stall. The issue is with the retry logic which schedules the timer if the created slots are less than NET_RX_SLOTS_MIN. The count of new request slots to be pushed are calculated as a difference between new req_prod and rsp_cons which could be more than the actual slots, if there are unconsumed responses. The fix is to calculate the count of newly created slots as the difference between new req_prod and old req_prod. Signed-off-by:
Vineeth Remanan Pillai <vineethp@amazon.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Stefano Stabellini authored
[ Upstream commit f1225ee4 ] In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original page is not suitable, we swap it for another page from the swiotlb pool. In these cases, we don't update the previously calculated dma address for the page before calling xen_dma_map_page. Thus, we end up calling xen_dma_map_page passing the wrong dev_addr, resulting in xen_dma_map_page mistakenly assuming that the page is foreign when it is local. Fix the bug by updating dev_addr appropriately. This change has no effect on x86, because xen_dma_map_page is a stub there. Signed-off-by:
Stefano Stabellini <sstabellini@kernel.org> Signed-off-by:
Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com> Tested-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
G. Campana authored
[ Upstream commit 8379cadf ] Using control_work instead of config_work as the 3rd argument to container_of results in an invalid portdev pointer. Indeed, the work structure is initialized as below: INIT_WORK(&portdev->config_work, &config_work_handler); It leads to a crash when portdev->vdev is dereferenced later. This bug is triggered when the guest uses a virtio-console without multiport feature and receives a config_changed virtio interrupt. Signed-off-by:
G. Campana <gcampana@quarkslab.com> Reviewed-by:
Amit Shah <amit.shah@redhat.com> Signed-off-by:
-
Liu Bo authored
[ Upstream commit 91298eec ] For such a file mapping, [0-4k][hole][8k-12k] In NO_HOLES mode, we don't have the [hole] extent any more. Commit c1aa4575 ("Btrfs: fix shrinking truncate when the no_holes feature is enabled") fixed disk isize not being updated in NO_HOLES mode when data is not flushed. However, even if data has been flushed, we can still have trouble in updating disk isize since we updated disk isize to 'start' of the last evicted extent. Reviewed-by:
Chris Mason <clm@fb.com> Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Gavin Shan authored
[ Upstream commit 387bbc97 ] We give up recovery on permanent error, simply shutdown the affected devices and remove them. If the devices can't be put into quiet state, they spew more traffic that is likely to cause another unexpected EEH error. This was observed on "p8dtu2u" machine: 0002:00:00.0 PCI bridge: IBM Device 03dc 0002:01:00.0 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.1 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.2 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.3 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) On P8 PowerNV platform, the IO path is frozen when shutdowning the devices, meaning the memory registers are inaccessible. It is why the devices can't be put into quiet state before removing them. This fixes the issue by enabling IO path prior to putting the devices into quiet state. Reported-by:
Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com> Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 3894396e ] bgmac_open() calls phy_start() to initialize the PHY state machine, which will set the interface's carrier state accordingly, no need to force that as this could be conflicting with the PHY state determined by PHYLIB. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit c3897f2a ] The driver does not start the transmit queue in bgmac_open(). If the queue was stopped prior to closing then re-opening the interface, we would never be able to wake-up again. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit d2b13233 ] We are checking for the Start of Frame bit in the ctl1 word, while this bit is set in the ctl0 word instead. Read the ctl0 word and update the check to verify that. Fixes: 9cde9450 ("bgmac: implement scatter/gather support") Signed-off-by:
-
David S. Miller authored
[ Upstream commit 750afbf8 ] Fixes: f1640c3d ("bgmac: fix a missing check for build_skb") Signed-off-by:
-
Rafał Miłecki authored
[ Upstream commit 36bcc0c9 ] Bit-flip errors may occur on NAND flashes and are harmless. Handle them gracefully as read content is still reliable and can be parsed. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
wangweidong authored
[ Upstream commit f1640c3d ] when build_skb failed, it may occure a NULL pointer. So add a 'NULL check' for it. Signed-off-by:
Weidong Wang <wangweidong1@huawei.com> Signed-off-by:
-
Rafał Miłecki authored
[ Upstream commit 2a36a5c3 ] We allowed using bcm47xxpart on BCM5301X arch with commit: 9e3afa5f ("mtd: bcm47xxpart: allow enabling on ARCH_BCM_5301X") BCM5301X devices may contain some partitions in higher memory, e.g. Netgear R8000 has board_data at 0x2600000. To detect them we should use size limit on MIPS only. Signed-off-by:
-
Álvaro Fernández Rojas authored
[ Upstream commit 07b50db6 ] Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> Cc: john@phrozen.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13307/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Álvaro Fernández Rojas authored
[ Upstream commit d7146829 ] Signed-off-by:
-
John Crispin authored
[ Upstream commit e906a5f6 ] A few fixes to the pinmux data, 2 new muxes and a minor whitespace cleanup. Signed-off-by:
John Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11991/Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit e6afb1ad ] Commit beb0babf ("korina: disable napi on close and restart") introduced calls to napi_disable() that were missing before, unfortunately this leaves a small window during which NAPI has a chance to run, yet we just freed resources since korina_free_ring() has been called: Fix this by disabling NAPI first then freeing resource, and make sure that we also cancel the restart task before doing the resource freeing. Fixes: beb0babf ("korina: disable napi on close and restart") Reported-by:
Alexandros C. Couloumbis <alex@ozo.com> Signed-off-by:
-
Jon Mason authored
[ Upstream commit 0c2bf9f9 ] GIC_PPI flags were misconfigured for the timers, resulting in errors like: [ 0.000000] GIC: PPI11 is secure or misconfigured Changing them to being edge triggered corrects the issue Suggested-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Jon Mason <jon.mason@broadcom.com> Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC") Signed-off-by:
-
