Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.

At the same time, rename the helper using an old underscore convention.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).

Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-07-31

This series contains updates to ice driver only.

Paul adds support for reporting what the link partner is advertising for
flow control settings.

Jake fixes the hardware statistics register which is prone to rollover
since the statistic registers are either 32 or 40 bits wide, depending
on which register is being read.  So use a 64 bit software statistic to
store off the hardware statistics to track past when it rolls over.
Fixes an issue with the locking of the control queue, where locks were
being destroyed at run time.

Tony fixes an issue that was created when interrupt tracking was
refactored and the call to ice_vsi_setup_vector_base() was removed from
the PF VSI instead of the VF VSI.  Adds a check before trying to
configure a port to ensure that media is attached.

Brett fixes an issue in the receive queue configuration where prefena
(Prefetch Enable) was being set to 0 which caused the hardware to only
fetch descriptors when there are none free in the cache for a received
packet.  Updates the driver to only bump the receive tail once per
napi_poll call, instead of the current model of bumping the tail up to 4
times per napi_poll call.  Adds statistics for receive drops at the port
level to ethtool/netlink.  Cleans up duplicate code in the allocation of
receive buffer code.

Akeem updates the driver to ensure that VFs stay disabled until the
setup or reset is completed.  Modifies the driver to use the allocated
number of transmit queues per VSI to set up the scheduling tree versus
using the total number of available transmit queues.  Also fix the
driver to update the total number of configured queues, after a
successful VF request to change its number of queues before updating the
corresponding VSI for that VF.  Cleaned up unnecessary flags that are no
longer needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: some code optimizations & bugfixes & features

This patch-set includes code optimizations, bugfixes and features for
the HNS3 ethernet controller driver.

[patch 01/12] adds support for reporting link change event.

[patch 02/12] adds handler for NCSI error.

[patch 03/12] fixes bug related to debugfs.

[patch 04/12] adds a code optimization for setting ring parameters.

[patch 05/12 - 09/12] adds some cleanups.

[patch 10/12 - 12/12] adds some patches related to reset issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling hclge_reset_event() within HCLGE_RESET_INTERVAL,
it returns directly now. If no one call it again, then the
error which needs a reset to fix it can not be fixed.

So this patch activates the reset timer for this case, and
adds checking in the end of the reset procedure to make this
error fixed earlier.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the reset interrupt is cleared in the reset task, which
is too late. Since, when the hardware finish the previous reset,
it can begin to do a new global/IMP reset, if this new coming reset
type is same as the previous one, the driver will clear them together,
then driver can not get that there is another reset, but the hardware
still wait for the driver to deal with the second one.

So this patch clears PF's reset interrupt status in the
hclge_irq_handle(), the hardware waits for handshaking from
driver before doing reset, so the driver and hardware deal with reset
one by one.

BTW, when VF doing global/IMP reset, it reads PF's reset interrupt
register to get that whether PF driver's re-initialization is done,
since VF's re-initialization should be done after PF's. So we add
a new command and a register bit to do that. When VF receive reset
interrupt, it sets up this bit, and PF finishes re-initialization
send command to clear this bit, then VF do re-initialization.

Fixes: 4ed340ab ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the driver sets handshake status to tell the hardware
that the driver have downed the netdev and it can continue with
reset process. The driver will clear the handshake status when
re-initializing the CMDQ, and does not recover this status
when reset fail, which may cause the hardware to wait for
the handshake status to be set and not being able to continue
with reset process.

So this patch delays clearing handshake status just before UP,
and recovers this status when reset fail.

BTW, this patch adds a new function hclge(vf)_reset_handshake() to
deal with the reset handshake issue, and renames
HCLGE(VF)_NIC_CMQ_ENABLE to HCLGE(VF)_NIC_SW_RST_RDY which
represents this register bit more accurately.

Fixes: ada13ee3 ("net: hns3: add handshake with hardware while doing reset")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The member 'mac_add' defined in hclge_mac_ethertype_idx_rd_cmd
means MAC address, so 'mac_addr' is a better name for it.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 4th and 5th parameter of hclge_cmd_query_error is useless, so this
patch removes them.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When hclge_tm_schd_info_update calls hclge_tm_schd_info_init to
initialize the schedule info, hdev->tm_info.num_pg and
hdev->tx_sch_mode is not changed, which makes the checking in
hclge_tm_schd_info_init unnecessary.

So this patch moves the hdev->tm_info.num_pg and hdev->tx_sch_mode
checking into hclge_tm_schd_init and changes the return type of
hclge_tm_schd_info_init from int to void.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The unused_count variable is used to indicate how many
RX BD need attaching new buffer in hns3_clean_rx_ring,
and the clean_count variable has the similar meaning.

This patch removes the clean_count variable and use
unused_count to uniformly indicate the RX BD that need
attaching new buffer.

This patch also clean up some coding style related to
variable assignment in hns3_clean_rx_ring.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The local variable return_status in hclge_get_mac_val_cmd_status()
is useless. So this patch returns the error code directly, instead of
using this variable. Also, replace some '%d' with '%u' in
hclge_get_mac_val_cmd_status().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, when changing the ring parameters, we free the old
ring resources firstly, and then setup the new ring resources.
In some case of an memory allocation fail, there will be no
resources to use. This patch refines it by setup new ring
resources and free the old ring resources in order.

Also reduce the max ring BD number to 32760 according to UM.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some commands are not supported on DCB-unsupported ports.
This patch distinguishes these commands and does not query
unsupported commands in debugfs.

This patch also fix an error in the dump "qos buf cfg"
command in debugfs.

Fixes: 2849d4e7 ("net: hns3: Add "tc config" info query function")
Fixes: 7d9d7f88 ("net: hns3: Add "qos buffer" config info query function")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NCSI has HW error, the IMP will report this error to the driver
by sending a mailbox. After received this message, the driver should
assert a global reset to fix this kind of HW error.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, PF updates link status per second. For some scenario,
it requires link down event being reported more quickly.
To solve it, firmware pushes the link change event to PF with
CMDQ message, and driver updates the link status directly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In user-space there's no way to distinguish why an mdb entry was deleted
and that is a problem for daemons which would like to keep the mdb in
sync with remote ends (e.g. mlag) but would also like to converge faster.
In almost all cases we'd like to age-out the remote entry for performance
and convergence reasons except when fast-leave is enabled. In that case we
want explicit immediate remote delete, thus add mdb flag which is set only
when the entry is being deleted due to fast-leave.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The -d command line argument to tdc requires the name of a physical device
on the system where the tests will be run. If -d has not been used, tdc
will skip tests that require a physical device.

This patch is intended to better document what the -d option does and how
it is used.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2019-07-29

This series includes updates to mlx5 driver,
1) Simplifications, cleanup and warning prints improvements

2) From Vlad Buslov:
Refactor mlx5 tc flow handling for unlocked execution (Part 1)

Currently, all cls API hardware offloads driver callbacks require caller
to hold rtnl lock when calling them. Cls API has already been updated to
update software filters in parallel (on classifiers that support
unlocked execution), however hardware offloads code still obtains rtnl
lock before calling driver tc callbacks. This set implements partial
support for unlocked execution that is leveraged by follow up
refactorings in specific mlx5 tc subsystems and patch to cls API that
implements API that allows drivers to register their callbacks as
rtnl-unlocked.

In mlx5 tc code mlx5e_tc_flow is the main structure that is used to
represent tc filter. Currently, code the structure itself and its
handlers in both tc and eswitch layers do not implement any kind of
synchronizations and assume external global synchronization provided by
rtnl lock instead. Implement following changes to remove dependency on
rtnl lock in flow handling code that are intended to be used a
groundwork for following changes to provide fully rtnl-independent mlx5
tc:

- Extend struct mlx5e_tc_flow with atomic reference counter and rcu to
  allow concurrent access from multiple tc and neigh update workqueue
  instances without introducing any additional locks specific to the
  structure. Its 'flags' field type is changed to atomic bitmask ops which
  is necessary for tc to interact with other concurrent tc instances or
  concurrent neigh update that need to skip flows that are not fully
  initialized (new INIT_DONE flow flag) and can change the flags
  according to neighbor state (flipping OFFLOADED flag).

- Protect unready flows list by new uplink_priv->unready_flows_lock
  mutex.

- Convert calls to netdev APIs that require rtnl lock in flow handling
  code to their rcu counterparts.

- Modify eswitch code that is called from tc layer and assume implicit
  external synchronization to be concurrency safe: change
  esw->offloads.num_flows type to atomic integer and re-arrange
  esw->state_lock usage to protect additional data.

Some of approaches to synchronizations presented in this patch set are
quite complicated (lockless concurrent usage of data structures with rcu
and reference counting, using fine-grained locking when necessary, retry
mechanisms to handle concurrent insertion of another instance of data
structure with same key, etc.). This is necessary to allow calling the
firmware in parallel in most cases, which is the main motivation of this
change since firmware calls are mach heavier operation than atomic
operations, multitude of locks and potential multiple retries during
concurrent accesses to same elements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update driver version to 0.7.5
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As a result of refactoring of VF VSIs interrupts code, there is no
need to track its configuration status again with ICE_VF_STATE_CFG_INTR
flag - In fact, it is not being checked anywhere in the code right now, so
this patch removes the dead code as applicable to the flag.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This flag is not needed and is called every time we re-enable interrupts
in the hotpath so remove it. Also remove ice_vsi_req_irq() because it
was a wrapper function for ice_vsi_req_irq_msix() whose sole purpose was
checking the ICE_FLAG_MSIX_ENA flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since Tx rings are being managed by FW/NVM, Tx rings might have not been
set up or driver had already wiped them off - In that case, call to
disable LAN Tx queue is being returned as not in existence. This patch
makes sure we don't return unnecessary error for such scenario.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the call to ice_alloc_mapped_page() fails we jump to the
no_buf label, possibly call ice_release_rx_desc(), and return true
indicating that there is more work to do. In the success case we just
fall out of the while loop, possibly call ice_alloc_mapped_page(), and
return false saying we exhausted cleaned_count. This flow can be
improved by breaking if ice_alloc_mapped_page() fails and then the flow
outside of the while loop is the same for the failure and success case.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we are not reporting dropped counts at the port level to
ethtool or netlink. This was found when debugging Rx dropped issues
and the total packets sent did not equal the total packets received
minus the rx_dropped, which was very confusing. To determine dropped
counts at the port level we need to read the PRTRPB_RDPC register.
To fix reporting we will store the dropped counts in the PF's
rx_discards. This will be reported to netlink by storing it in the
PF VSI's rx_missed_errors signaling that the receiver missed the
packet. Also, we will report this to ethtool in the rx_dropped.nic
field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In case there is a request from a VF to change its number of queues, and
the request was successful, we need to update number of queues
configured on the VF before updating corresponding VSI for that VF,
especially LAN Tx queue tree and TC update, otherwise, we would continued
to use old value of vf->num_vf_qs for allocated Tx/Rx queues...
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch uses allocated number of Tx queues per VSI to set up its
scheduling tree instead of using total number of available Tx queues.
Only PF VSIs have total number of allocated Tx queues equal to number
of available Tx queues, other VSIs have different number of queues
configured.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we bump the Rx tail and release/give buffers to hardware every
16 descriptors. This causes us to bump Rx tail up to 4 times per
napi_poll call. Also we are always bumping tail on an odd index and this
is a problem because hardware ignores the lower 3 bits in the QRX_TAIL
register. This is making it so hardware sees tail bumps only every 8
descriptors. Instead lets only bump Rx tail once per napi_poll if
the value aligns with hardware's expectations of the lower 3 bits being
cleared. Also only release/give Rx buffers once per napi_poll call.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to clear VFs enable status until reset is completed,
and Tx/Rx rings are setup. Without this patch, the code flow request Tx
queues to be disabled after reset, especially PFR - where VF VSI Tx rings
have already been wiped off in the NVM and result to adminq error based on
the call to disable Tx LAN queue in ice_reset_all_vfs function call.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware reports an error when trying to configure a port with no
media. Instead of always configuring the port, check for media before
attempting to configure it. In the absence of media, turn off link and
poll for media to become available before re-enabling link.

Move ice_force_phys_link_state() up to avoid forward declaration.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>