- 18 May, 2022 1 commit
-
-
Mingzhe Zou authored
In commit d72d827f, I used 'cpumask_t' incorrectly: void iscsit_thread_get_cpumask(struct iscsi_conn *conn) { int ord, cpu; cpumask_t conn_allowed_cpumask; ...... } static ssize_t lio_target_wwn_cpus_allowed_list_store( struct config_item *item, const char *page, size_t count) { int ret; char *orig; cpumask_t new_allowed_cpumask; ...... } The correct pattern should be as follows: cpumask_var_t mask; if (!zalloc_cpumask_var(&mask, GFP_KERNEL)) return -ENOMEM; ... use 'mask' here ... free_cpumask_var(mask); Link: https://lore.kernel.org/r/20220516054721.1548-1-mingzhe.zou@easystack.cn Fixes: d72d827f ("scsi: target: Add iscsi/cpus_allowed_list in configfs") Reported-by:
Test Bot <zgrieee@gmail.com> Reviewed-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
Mingzhe Zou <mingzhe.zou@easystack.cn> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
- 11 May, 2022 2 commits
-
-
James Smart authored
Garbage FCoE CT frames are transmitted on the wire because of bad DMA ptr addresses filled in the GEN_REQ_WQE. The __lpfc_sli_prep_gen_req_s4() routine is using the wrong buffer for the payload address. Change the DMA buffer assignment from the bmp buffer to the bpl buffer. Link: https://lore.kernel.org/r/20220506205548.61644-1-jsmart2021@gmail.com Fixes: 61910d6a ("scsi: lpfc: SLI path split: Refactor CT paths") Co-developed-by:
Justin Tee <justin.tee@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
-
James Smart authored
The refactoring code converted context information from SLI-3 to SLI-4. The conversion for the SLI-4 bit field tried to use the old (hacky) SLI3 high/low bit settings. Needless to say, it was incorrect. Explicitly set the context field to type FCFI and set it in the wqe. SLI-4 is now a proper bit field so no need for the shifting/anding. Link: https://lore.kernel.org/r/20220506205528.61590-1-jsmart2021@gmail.com Fixes: 6831ce12 ("scsi: lpfc: SLI path split: Refactor base ELS paths and the FLOGI path") Co-developed-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
-
- 03 May, 2022 1 commit
-
-
Gleb Chesnokov authored
Aborting commands that have already been sent to the firmware can cause BUG in qlt_free_cmd(): BUG_ON(cmd->sg_mapped) For instance: - Command passes rdx_to_xfer state, maps sgl, sends to the firmware - Reset occurs, qla2xxx performs ISP error recovery, aborts the command - Target stack calls qlt_abort_cmd() and then qlt_free_cmd() - BUG_ON(cmd->sg_mapped) in qlt_free_cmd() occurs because sgl was not unmapped Thus, unmap sgl in qlt_abort_cmd() for commands with the aborted flag set. Link: https://lore.kernel.org/r/AS8PR10MB4952D545F84B6B1DFD39EC1E9DEE9@AS8PR10MB4952.EURPRD10.PROD.OUTLOOK.COMReviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
Gleb Chesnokov <Chesnokov.G@raidix.com> Signed-off-by:
-
- 02 May, 2022 1 commit
-
-
Brian Bunker authored
The handling of the ALUA transitioning state is currently broken. When a target goes into this state, it is expected that the target is allowed to stay in this state for the implicit transition timeout without a path failure. The handler has this logic, but it gets skipped currently. When the target transitions, there is in-flight I/O from the initiator. The first of these responses from the target will be a unit attention letting the initiator know that the ALUA state has changed. The remaining in-flight I/Os, before the initiator finds out that the portal state has changed, will return not ready, ALUA state is transitioning. The portal state will change to SCSI_ACCESS_STATE_TRANSITIONING. This will lead to all new I/O immediately failing the path unexpectedly. The path failure happens in less than a second instead of the expected successes until the transition timer is exceeded. Allow I/Os to continue while the path is in the ALUA transitioning state. The handler already takes care of a target that stays in the transitioning state for too long by changing the state to ALUA state standby once the transition timeout is exceeded at which point the path will fail. Link: https://lore.kernel.org/r/CAHZQxy+4sTPz9+pY3=7VJH+CLUJsDct81KtnR2be8ycN5mhqTg@mail.gmail.comReviewed-by:
Hannes Reinecke <hare@suse.de> Acked-by:
Krishna Kant <krishna.kant@purestorage.com> Acked-by:
Seamus Connor <sconnor@purestorage.com> Signed-off-by:
Brian Bunker <brian@purestorage.com> Signed-off-by:
-
- 28 Apr, 2022 1 commit
-
-
David Jeffery authored
With tape devices, the SCF_TREAT_READ_AS_NORMAL flag is used by the target subsystem to mark commands which have both data to return as well as sense data. But with pscsi, SCF_TREAT_READ_AS_NORMAL can be set even if there is no data to return. The SCF_TREAT_READ_AS_NORMAL flag causes the target core to call iscsit data-in callbacks even if there is no data, which iscsit does not support. This results in iscsit going into an error state requiring recovery and being unable to complete the command to the initiator. This issue can be resolved by fixing pscsi to only set SCF_TREAT_READ_AS_NORMAL if there is valid data to return alongside the sense data. Link: https://lore.kernel.org/r/20220427183250.291881-1-djeffery@redhat.com Fixes: bd813720 ("scsi: target: transport should handle st FM/EOM/ILI reads") Reported-by:
Scott Hamilton <scott.hamilton@atos.net> Tested-by:
Laurence Oberman <loberman@redhat.com> Reviewed-by:
David Jeffery <djeffery@redhat.com> Signed-off-by:
-
- 19 Apr, 2022 1 commit
-
-
Tom Rix authored
sr_ioctl.c uses this pattern: result = sr_do_ioctl(cd, &cgc); to-user = buffer[]; kfree(buffer); return result; Use of a buffer without checking leaks information. Check result and jump over the use of buffer if there is an error. result = sr_do_ioctl(cd, &cgc); if (result) goto err; to-user = buffer[]; err: kfree(buffer); return result; Additionally, initialize the buffer to zero. This problem can be seen in the 2.4.0 kernel. Link: https://lore.kernel.org/r/20220411174756.2418435-1-trix@redhat.com Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reviewed-by:Christoph Hellwig <hch@lst.de> Signed-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
-
- 12 Apr, 2022 13 commits
-
-
Mike Christie authored
I've been doing a lot of iscsi patches because Oracle is paying me to work on iSCSI again. It was supposed to be temp assignment, but my co-worker that was working on iscsi moved to a new group so it looks like I'm back on this code again. After talking to Chris and Lee this patch adds me back as co-maintainer, so I can help them and people remember to cc me on issues. Link: https://lore.kernel.org/r/20220408001314.5014-11-michael.christie@oracle.comTested-by:
Manish Rangankar <mrangankar@marvell.com> Acked-by:
Lee Duncan <lduncan@suse.com> Acked-by:
Chris Leech <cleech@redhat.com> Signed-off-by:
-
Mike Christie authored
We set the qedi_ep state to EP_STATE_OFLDCONN_START when the ep is created. Then in qedi_set_path we kick off the offload work. If userspace times out the connection and calls ep_disconnect, qedi will only flush the offload work if the qedi_ep state has transitioned away from EP_STATE_OFLDCONN_START. If we can't connect we will not have transitioned state and will leave the offload work running, and we will free the qedi_ep from under it. This patch just has us init the work when we create the ep, then always flush it. Link: https://lore.kernel.org/r/20220408001314.5014-10-michael.christie@oracle.comTested-by:
-
Mike Christie authored
If a offload driver doesn't use the xmit workqueue, then when we are doing ep_disconnect libiscsi can still inject PDUs to the driver. This adds a check for if the connection is bound before trying to inject PDUs. Link: https://lore.kernel.org/r/20220408001314.5014-9-michael.christie@oracle.comTested-by:
-
Mike Christie authored
Move the tx and rx suspend fields into one flags field. Link: https://lore.kernel.org/r/20220408001314.5014-8-michael.christie@oracle.comTested-by:
-
Mike Christie authored
If a driver raises a connection error before the connection is bound, we can leave a cleanup_work queued that can later run and disconnect/stop a connection that is logged in. The problem is that drivers can call iscsi_conn_error_event for endpoints that are connected but not yet bound when something like the network port they are using is brought down. iscsi_cleanup_conn_work_fn will check for this and exit early, but if the cleanup_work is stuck behind other works, it might not get run until after userspace has done ep_disconnect. Because the endpoint is not yet bound there was no way for ep_disconnect to flush the work. The bug of leaving stop_conns queued was added in: Commit 23d6fefb ("scsi: iscsi: Fix in-kernel conn failure handling") and: Commit 0ab71045 ("scsi: iscsi: Perform connection failure entirely in kernel space") was supposed to fix it, but left this case. This patch moves the conn state check to before we even queue the work so we can avoid queueing. Link: https://lore.kernel.org/r/20220408001314.5014-7-michael.christie@oracle.com Fixes: 0ab71045 ("scsi: iscsi: Perform connection failure entirely in kernel space") Tested-by:
-
Mike Christie authored
If iscsid is doing a stop_conn at the same time the kernel is starting error recovery we can hit a race that allows the cleanup work to run on a valid connection. In the race, iscsi_if_stop_conn sees the cleanup bit set, but it calls flush_work on the clean_work before iscsi_conn_error_event has queued it. The flush then returns before the queueing and so the cleanup_work can run later and disconnect/stop a conn while it's in a connected state. The patch: Commit 0ab71045 ("scsi: iscsi: Perform connection failure entirely in kernel space") added the late stop_conn call bug originally, and the patch: Commit 23d6fefb ("scsi: iscsi: Fix in-kernel conn failure handling") attempted to fix it but only fixed the normal EH case and left the above race for the iscsid restart case. For the normal EH case we don't hit the race because we only signal userspace to start recovery after we have done the queueing, so the flush will always catch the queued work or see it completed. For iscsid restart cases like boot, we can hit the race because iscsid will call down to the kernel before the kernel has signaled any error, so both code paths can be running at the same time. This adds a lock around the setting of the cleanup bit and queueing so they happen together. Link: https://lore.kernel.org/r/20220408001314.5014-6-michael.christie@oracle.com Fixes: 0ab71045 ("scsi: iscsi: Perform connection failure entirely in kernel space") Tested-by:
-
Mike Christie authored
This patch fixes a bug where when using iSCSI offload we can free an endpoint while userspace still thinks it's active. That then causes the endpoint ID to be reused for a new connection's endpoint while userspace still thinks the ID is for the original connection. Userspace will then end up disconnecting a running connection's endpoint or trying to bind to another connection's endpoint. This bug is a regression added in: Commit 23d6fefb ("scsi: iscsi: Fix in-kernel conn failure handling") where we added a in kernel ep_disconnect call to fix a bug in: Commit 0ab71045 ("scsi: iscsi: Perform connection failure entirely in kernel space") where we would call stop_conn without having done ep_disconnect. This early ep_disconnect call will then free the endpoint and it's ID while userspace still thinks the ID is valid. Fix the early release of the ID by having the in kernel recovery code keep a reference to the endpoint until userspace has called into the kernel to finish cleaning up the endpoint/connection. It requires the previous commit "scsi: iscsi: Release endpoint ID when its freed" which moved the freeing of the ID until when the endpoint is released. Link: https://lore.kernel.org/r/20220408001314.5014-5-michael.christie@oracle.com Fixes: 23d6fefb ("scsi: iscsi: Fix in-kernel conn failure handling") Tested-by:
-
Mike Christie authored
We can't release the endpoint ID until all references to the endpoint have been dropped or it could be allocated while in use. This has us use an idr instead of looping over all conns to find a free ID and then free the ID when all references have been dropped instead of when the device is only deleted. Link: https://lore.kernel.org/r/20220408001314.5014-4-michael.christie@oracle.comTested-by:
Wu Bo <wubo40@huawei.com> Signed-off-by:
-
Mike Christie authored
When userspace restarts during boot or upgrades it won't know about the offload driver's endpoint and connection mappings. iscsid will start by cleaning up the old session by doing a stop_conn call. Later, if we are able to create a new connection, we clean up the old endpoint during the binding stage. The problem is that if we do stop_conn before doing the ep_disconnect call offload, drivers can still be executing I/O. We then might free tasks from the under the card/driver. This moves the ep_disconnect call to before we do the stop_conn call for this case. It will then work and look like a normal recovery/cleanup procedure from the driver's point of view. Link: https://lore.kernel.org/r/20220408001314.5014-3-michael.christie@oracle.comTested-by:
-
Mike Christie authored
This patch moves iscsi_ep_disconnect() so it can be called earlier in the next patch. Link: https://lore.kernel.org/r/20220408001314.5014-2-michael.christie@oracle.comTested-by:
-
Ajish Koshy authored
Executing driver on servers with more than 32 CPUs were faced with command timeouts. This is because we were not geting completions for commands submitted on IQ32 - IQ63. Set E64Q bit to enable upper inbound and outbound queues 32 to 63 in the MPI main configuration table. Added 500ms delay after successful MPI initialization as mentioned in controller datasheet. Link: https://lore.kernel.org/r/20220411064603.668448-3-Ajish.Koshy@microchip.com Fixes: 05c6c029 ("scsi: pm80xx: Increase number of supported queues") Reviewed-by:
Damien Le Moal <damien.lemoal@opensource.wdc.com> Acked-by:
Jack Wang <jinpu.wang@ionos.com> Signed-off-by:
Ajish Koshy <Ajish.Koshy@microchip.com> Signed-off-by:
Viswas G <Viswas.G@microchip.com> Signed-off-by:
-
Ajish Koshy authored
When upper inbound and outbound queues 32-63 are enabled, we see upper vectors 32-63 in interrupt service routine. We need corresponding registers to handle masking and unmasking of these upper interrupts. To achieve this, we use registers MSGU_ODMR_U(0x34) to mask and MSGU_ODMR_CLR_U(0x3C) to unmask the interrupts. In these registers bit 0-31 represents interrupt vectors 32-63. Link: https://lore.kernel.org/r/20220411064603.668448-2-Ajish.Koshy@microchip.com Fixes: 05c6c029 ("scsi: pm80xx: Increase number of supported queues") Reviewed-by:
John Garry <john.garry@huawei.com> Acked-by:
-
Bart Van Assche authored
Revert the patch mentioned in the subject since it blocks I/O after module unload has started while this is a legitimate use case. For e.g. blktests test case srp/001 that patch causes a command timeout to be triggered for the following call stack: __schedule+0x4c3/0xd20 schedule+0x82/0x110 schedule_timeout+0x122/0x200 io_schedule_timeout+0x7b/0xc0 __wait_for_common+0x2bc/0x380 wait_for_completion_io_timeout+0x1d/0x20 blk_execute_rq+0x1db/0x200 __scsi_execute+0x1fb/0x310 sd_sync_cache+0x155/0x2c0 [sd_mod] sd_shutdown+0xbb/0x190 [sd_mod] sd_remove+0x5b/0x80 [sd_mod] device_remove+0x9a/0xb0 device_release_driver_internal+0x2c5/0x360 device_release_driver+0x12/0x20 bus_remove_device+0x1aa/0x270 device_del+0x2d4/0x640 __scsi_remove_device+0x168/0x1a0 scsi_forget_host+0xa8/0xb0 scsi_remove_host+0x9b/0x150 sdebug_driver_remove+0x3d/0x140 [scsi_debug] device_remove+0x6f/0xb0 device_release_driver_internal+0x2c5/0x360 device_release_driver+0x12/0x20 bus_remove_device+0x1aa/0x270 device_del+0x2d4/0x640 device_unregister+0x18/0x70 sdebug_do_remove_host+0x138/0x180 [scsi_debug] scsi_debug_exit+0x45/0xd5 [scsi_debug] __do_sys_delete_module.constprop.0+0x210/0x320 __x64_sys_delete_module+0x1f/0x30 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae Link: https://lore.kernel.org/r/20220409043704.28573-1-bvanassche@acm.org Fixes: 2aad3cd8 ("scsi: scsi_debug: Address races following module load") Cc: Douglas Gilbert <dgilbert@interlog.com> Cc: Yi Zhang <yi.zhang@redhat.com> Cc: Bob Pearson <rpearsonhpe@gmail.com> Reported-by:
Yi Zhang <yi.zhang@redhat.com> Tested-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
-
- 07 Apr, 2022 12 commits
-
-
Chandrakanth patil authored
The megaraid_sas driver supports single LUN for RAID devices. That is LUN 0. All other LUNs are unsupported. When a device scan on a logical target with invalid LUN number is invoked through sysfs, that target ends up getting removed. Add LUN ID validation in the slave destroy function to avoid the target deletion. Link: https://lore.kernel.org/r/20220324094711.48833-1-chandrakanth.patil@broadcom.comSigned-off-by:
Chandrakanth patil <chandrakanth.patil@broadcom.com> Signed-off-by:
-
Xiaomeng Tong authored
The list iterator is always non-NULL so the check 'if (!rgn)' is always false and the dev_err() is never called. Move the check outside the loop and determine if 'victim_rgn' is NULL, to fix this bug. Link: https://lore.kernel.org/r/20220320150733.21824-1-xiam0nd.tong@gmail.com Fixes: 4b5f4907 ("scsi: ufs: ufshpb: L2P map management for HPB read") Reviewed-by:
Daejun Park <daejun7.park@samsung.com> Signed-off-by:
Xiaomeng Tong <xiam0nd.tong@gmail.com> Signed-off-by:
-
Wenchao Hao authored
We forgot to call blk_cleanup_disk() when device_add_disk() failed. This would cause a memory leak of gendisk and sched_tags allocated in elevator_init_mq() Reference:https://syzkaller.appspot.com/x/log.txt?x=13b41dcb700000 Reported-and-tested-by: syzbot+f08c77040fa163a75a46@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20220401011018.1026553-1-haowenchao@huawei.comSigned-off-by:
Wenchao Hao <haowenchao@huawei.com> Signed-off-by:
-
Colin Ian King authored
Variable dmp is being assigned a value that is never read, the variable is redundant and can be removed. Cleans up clang scan build warning: drivers/message/fusion/mptbase.c:6667:39: warning: Although the value stored to 'dmp' is used in the enclosing expression, the value is never actually read from 'dmp' [deadcode.DeadStores] Link: https://lore.kernel.org/r/20220318003927.81471-1-colin.i.king@gmail.comReviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
Alexey Galakhov authored
The HighPoint RocketRaid 2640 is a low-cost SAS controller based on Marvell chip. The chip in question was already supported by the kernel, just the PCI ID of this particular board was missing. Link: https://lore.kernel.org/r/20220309212535.402987-1-agalakhov@gmail.comSigned-off-by:
Alexey Galakhov <agalakhov@gmail.com> Signed-off-by:
-
Martin K. Petersen authored
As such it should be called inside the scsi_device_supports_vpd() conditional. Link: https://lore.kernel.org/r/20220302053559.32147-13-martin.petersen@oracle.com Fixes: e815d365 ("scsi: sd: add concurrent positioning ranges support") Cc: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by:
-
Sreekanth Reddy authored
As part of controller reset operation the driver issues a config request command. If this command gets times out, then fail the controller reset operation instead of retrying it. Link: https://lore.kernel.org/r/20220405120637.20528-1-sreekanth.reddy@broadcom.comSigned-off-by:
Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by:
-
Finn Thain authored
This driver doesn't use SCp.ptr to save a SCSI command data pointer which means "scsi pointer" is a complete misnomer here. Only a few members of struct scsi_pointer are needed so move those to private command data. Link: https://lore.kernel.org/r/accf71e293ba3aed6d18c8baeb405de8dfe7c935.1649235939.git.fthain@linux-m68k.org Cc: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by:
Finn Thain <fthain@linux-m68k.org> Signed-off-by:
-
Adrian Hunter authored
Add PCI ID and callbacks to support Intel Meteor Lake (MTL). Link: https://lore.kernel.org/r/20220404055038.2208051-1-adrian.hunter@intel.com Cc: stable@vger.kernel.org # v5.15+ Reviewed-by:
Avri Altman <avri.altman@wdc.com> Reviewed-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Damien Le Moal authored
The start_addres argument of mpt3sas_check_same_4gb_region() was misnamed in the function kdoc comment, resulting in the following warning when compiling with W=1. drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Function parameter or member 'start_address' not described in 'mpt3sas_check_same_4gb_region' drivers/scsi/mpt3sas/mpt3sas_base.c:5728: warning: Excess function parameter 'reply_pool_start_address' description in 'mpt3sas_check_same_4gb_region' Fix the argument name in the function kdoc comment to avoid it. While at it, remove a useless blank line between the kdoc and function code. Link: https://lore.kernel.org/r/20220404050041.594774-1-damien.lemoal@opensource.wdc.comAcked-by:
-
Damien Le Moal authored
The in_use_bm bitmap of struct sdebug_queue should be accessed under protection of the qc_lock spinlock. Make sure that this lock is taken before calling find_first_bit() at the beginning of the function sdebug_blk_mq_poll(). Link: https://lore.kernel.org/r/20220404045547.579887-1-damien.lemoal@opensource.wdc.com Fixes: 3fd07aec ("scsi: scsi_debug: Fix qc_lock use in sdebug_blk_mq_poll()") Acked-by:
-
Martin K. Petersen authored
Pull the remaining commits from 5.18/scsi-queue into fixes. Signed-off-by:
-
- 03 Apr, 2022 8 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-traceLinus Torvalds authored
Pull more tracing updates from Steven Rostedt: - Rename the staging files to give them some meaning. Just stage1,stag2,etc, does not show what they are for - Check for NULL from allocation in bootconfig - Hold event mutex for dyn_event call in user events - Mark user events to broken (to work on the API) - Remove eBPF updates from user events - Remove user events from uapi header to keep it from being installed. - Move ftrace_graph_is_dead() into inline as it is called from hot paths and also convert it into a static branch. * tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Move user_events.h temporarily out of include/uapi ftrace: Make ftrace_graph_is_dead() a static branch tracing: Set user_events to BROKEN tracing/user_events: Remove eBPF interfaces tracing/user_events: Hold event_mutex during dyn_event_add proc: bootconfig: Add null pointer check tracing: Rename the staging files for trace_events
-
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linuxLinus Torvalds authored
Pull clk fix from Stephen Boyd: "A single revert to fix a boot regression seen when clk_put() started dropping rate range requests. It's best to keep various systems booting so we'll kick this out and try again next time" * tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: Revert "clk: Drop the rate range on clk_put()"
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A set of x86 fixes and updates: - Make the prctl() for enabling dynamic XSTATE components correct so it adds the newly requested feature to the permission bitmap instead of overwriting it. Add a selftest which validates that. - Unroll string MMIO for encrypted SEV guests as the hypervisor cannot emulate it. - Handle supervisor states correctly in the FPU/XSTATE code so it takes the feature set of the fpstate buffer into account. The feature sets can differ between host and guest buffers. Guest buffers do not contain supervisor states. So far this was not an issue, but with enabling PASID it needs to be handled in the buffer offset calculation and in the permission bitmaps. - Avoid a gazillion of repeated CPUID invocations in by caching the values early in the FPU/XSTATE code. - Enable CONFIG_WERROR in x86 defconfig. - Make the X86 defconfigs more useful by adapting them to Y2022 reality" * tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/fpu/xstate: Consolidate size calculations x86/fpu/xstate: Handle supervisor states in XSTATE permissions x86/fpu/xsave: Handle compacted offsets correctly with supervisor states x86/fpu: Cache xfeature flags from CPUID x86/fpu/xsave: Initialize offset/size cache early x86/fpu: Remove unused supervisor only offsets x86/fpu: Remove redundant XCOMP_BV initialization x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO x86/config: Make the x86 defconfigs a bit more usable x86/defconfig: Enable WERROR selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull RT signal fix from Thomas Gleixner: "Revert the RT related signal changes. They need to be reworked and generalized" * tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull more dma-mapping updates from Christoph Hellwig: - fix a regression in dma remap handling vs AMD memory encryption (me) - finally kill off the legacy PCI DMA API (Christophe JAILLET) * tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping: dma-mapping: move pgprot_decrypted out of dma_pgprot PCI/doc: cleanup references to the legacy PCI DMA API PCI: Remove the deprecated "pci-dma-compat.h" API
-
git://git.armlinux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fixes from Russell King: - avoid unnecessary rebuilds for library objects - fix return value of __setup handlers - fix invalid input check for "crashkernel=" kernel option - silence KASAN warnings in unwind_frame * tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame() ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0' ARM: 9187/1: JIVE: fix return value of __setup handler ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects
-
Stephen Boyd authored
This reverts commit 7dabfa2b. There are multiple reports that this breaks boot on various systems. The common theme is that orphan clks are having rates set on them when that isn't expected. Let's revert it out for now so that -rc1 boots. Reported-by:
Marek Szyprowski <m.szyprowski@samsung.com> Reported-by:
Tony Lindgren <tony@atomide.com> Reported-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Reported-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com Cc: Maxime Ripard <maxime@cerno.tech> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org
-
