- 24 Nov, 2022 28 commits
-
-
Johan Hovold authored
Clean up and unify the DP callbacks by dropping the redundant "qcom" and "phy" prefix and infix and by using a common naming scheme ("qmp" + version + callback name). Reviewed-by:Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20221114110621.4639-23-johan+linaro@kernel.orgSigned-off-by:
Vinod Koul <vkoul@kernel.org>
-
Johan Hovold authored
Stop abusing the driver data pointer and instead pass the driver state structure directly to the initialisation helpers during probe. Reviewed-by:
-
Johan Hovold authored
Since the QMP driver split there will be precisely two child nodes so drop the obsolete iteration construct. While at it, drop the verbose error logging that would have been printed also on probe deferrals. Note that there is no need to check if there are additional child nodes (the kernel is not a devicetree validator), but let's return an error if either child node is missing. Reviewed-by:
-
Johan Hovold authored
The QMP combo driver manages a single PHY (even if it provides two interfaces for USB and DP, respectively) so merge the old qcom_qmp and qmp_phy structures and drop the PHY array. Reviewed-by:
-
Johan Hovold authored
It does not really make any sense to keep separate configuration structures for the USB and DP parts of the same PHY so merge them. Reviewed-by:
-
Johan Hovold authored
Since the QMP driver split there is really no need for the 'lanes' configuration parameter as all of these USB-C PHYs support dual-lane SuperSpeed USB and quad-lane (uni-directional) DP (even if the driver still only supports CC1 orientation using lanes 2 and 3). Signed-off-by:
-
Johan Hovold authored
In preparation for merging the USB and DP configurations, add dedicated pointers for the DP serdes and tx tables to the configurations. Reviewed-by:
-
Johan Hovold authored
In preparation for merging the USB and DP configurations, drop the "combo" infix from the SC8280XP combined configuration for consistency with the other platforms. Reviewed-by:
-
Johan Hovold authored
In preparation for merging the USB and DP configurations, align the initialisations of the DP function pointers. Reviewed-by:
-
Johan Hovold authored
In preparation for merging the driver data, add separate iomem pointers for the DP part of the PHY. Reviewed-by:
-
Johan Hovold authored
Separate the devicetree parsing of the USB and DP child nodes in two dedicated helpers in preparation for merging the driver data. Note that only the USB part of the PHY has a pipe clock and that the DP implementation only uses the tx/tx2 and pcs register regions. Reviewed-by:
-
Johan Hovold authored
Clean up serdes initialisation somewhat by making the current helper a dedicated helper for the DP part of the PHY. Note that no error is currently returned for non-supported link rates. Reviewed-by:
-
Johan Hovold authored
Separate the USB and DP power-on and power-off operations in two dedicated implementations. Note that the pipe clock is only used by the USB part of the PHY and that no DP configuration has a pcs (or rx) table or has has_pwrdn_delay set. Reviewed-by:
-
Johan Hovold authored
Rename the configure and calibrate DP PHY ops using the common prefix for consistency. Reviewed-by:
-
Johan Hovold authored
Separate the USB and DP init and exit operations by calling the common initialisation code directly from the USB operation and adding a "dp" infix to the DP callbacks. Reviewed-by:
-
Johan Hovold authored
Drop the unnecessary (verbose) debug message from the init PHY op. Reviewed-by:
-
Johan Hovold authored
Add a "usb" infix to the USB PHY operation functions and name them after the corresponding operations (e.g. "init" rather than "enable"). Reviewed-by:
-
Johan Hovold authored
The set-mode operation is currently only used by the USB part of the PHY so drop the corresponding callback from the DP PHY ops. Reviewed-by:
-
Johan Hovold authored
Rename the PHY operation structures so that they have a "phy_ops" suffix and move them next to the implementation. Reviewed-by:
-
Johan Hovold authored
Move the PM ops structure next to the implementation to keep the driver callbacks grouped. Reviewed-by:
-
Johan Hovold authored
Move the device-id table after probe() and next to the driver structure to keep the driver callback functions grouped together. Reviewed-by:
-
Johan Hovold authored
Sort the device-id table by compatible string to make it easier to find and add new entries. Reviewed-by:
-
Johan Hovold authored
Commit 52e013d0 ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy") added support for the DisplayPort part of QMP PHYs but unfortunately did so by duplicating parts of the shared configuration, something which has lead to subtle bugs depending on probe order. As the resources have always been requested based on the USB configuration, make sure to not rely on fields from the DP configuration when using them (e.g. in case they get out of sync) and remove the now unused fields from the DP configurations. Reviewed-by:
-
Johan Hovold authored
Drop the confused runtime-suspend type check which effectively broke runtime PM if the DP child node happens to be parsed before the USB child node during probe (e.g. due to order of child nodes in the devicetree). Instead use the new driver data USB PHY pointer to access the USB configuration and resources. Fixes: 52e013d0 ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy") Reviewed-by:
-
Johan Hovold authored
The PHY is powered on during phy-init by setting the SW_PWRDN bit in the COM_POWER_DOWN_CTRL register and then setting the same bit in the in the PCS_POWER_DOWN_CONTROL register that belongs to the USB part of the PHY. Currently, whether power on succeeds depends on probe order and having the USB part of the PHY be initialised first. In case the DP part of the PHY is instead initialised first, the intended power on of the USB block results in a corrupted DP_PHY register (e.g. DP_PHY_AUX_CFG8). Add a pointer to the USB part of the PHY to the driver data and use that to power on the PHY also if the DP part of the PHY is initialised first. Fixes: 52e013d0 ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy") Cc: stable@vger.kernel.org # 5.10 Reviewed-by:
-
Johan Hovold authored
The SC8180X has two resets but the DP configuration erroneously described only one. In case the DP part of the PHY is initialised before the USB part (e.g. depending on probe order), then only the first reset would be asserted. Fixes: 1633802c ("phy: qcom: qmp: Add SC8180x USB/DP combo") Cc: stable@vger.kernel.org # 5.15 Reviewed-by:
-
Johan Hovold authored
The SDM845 has two resets but the DP configuration erroneously described only one. In case the DP part of the PHY is initialised before the USB part (e.g. depending on probe order), then only the first reset would be asserted. Add a dedicated configuration for SDM845 rather than reuse the incompatible SC7180 configuration. Fixes: d88497fb ("phy: qualcomm: phy-qcom-qmp: add support for combo USB3+DP phy on SDM845") Cc: stable@vger.kernel.org # 6.1 Reviewed-by:
-
Johan Hovold authored
The SM8250 only uses three clocks but the DP configuration erroneously described four clocks. In case the DP part of the PHY is initialised before the USB part, this would lead to uninitialised memory beyond the bulk-clocks array to be treated as a clock pointer as the clocks are requested based on the USB configuration. Fixes: aff188fe ("phy: qcom-qmp: add support for sm8250-usb3-dp phy") Cc: stable@vger.kernel.org # 5.13 Reviewed-by:
-
- 10 Nov, 2022 12 commits
-
-
Yoshihiro Shimoda authored
Add Renesas Ethernet SERDES driver for R-Car S4-8 (r8a779f0). The datasheet describes initialization procedure without any information about registers' name/bits. So, this is all black magic to initialize the hardware. Especially, all channels should be initialized at once. Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/20221108005500.3011449-3-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Yoshihiro Shimoda authored
Document Renesas Etherent SERDES for R-Car S4-8 (r8a779f0). Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20221108005500.3011449-2-yoshihiro.shimoda.uh@renesas.comSigned-off-by:
-
Manivannan Sadhasivam authored
sm8450_qmp_gen4x2_pcie_pcs_tbl[] contains the init sequence for PCS registers of QMP PHY v5.20. So use the v5.20 specific register names. Only major change is the rename of PCS_EQ_CONFIG{2/3} registers to PCS_EQ_CONFIG{4/5}. Fixes: 2c91bf6b ("phy: qcom-qmp: Add SM8450 PCIe1 PHY support") Signed-off-by:Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20221102081835.41892-2-manivannan.sadhasivam@linaro.orgSigned-off-by:
-
Manivannan Sadhasivam authored
The PCIe QMP 4x2 RC PHY generates high latency when ASPM is enabled. This seem to be fixed by clearing the QPHY_V5_20_PCS_PCIE_PRESET_P10_POST register of the pcs_misc register space. Fixes: 2c91bf6b ("phy: qcom-qmp: Add SM8450 PCIe1 PHY support") Signed-off-by:
-
Christian Marangi authored
Commit af664324 ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018 pcie gen3") reworked the pcs regs values and removed the 0x400 offset for each pcs_misc regs. This change caused the malfunction of ipq8074 downstream since it still has the legacy pcs table where pcs_misc are not placed on a different table and instead put together assuming the offset of 0x400 for the related pcs_misc regs. Split pcs_misc init cfg from the ipq8074 pcs init table to be handled correctly to prepare for actual support for gen3 pcie for ipq8074. Fixes: af664324 ("phy: qcom-qmp-pcie: split pcs_misc region for ipq6018 pcie gen3") Reported-by:
Robert Marko <robimarko@gmail.com> Tested-by:
Christian Marangi <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20221103212125.17156-1-ansuelsmth@gmail.comSigned-off-by:
-
Johan Hovold authored
The PCIe2 and PCIe3 controllers and PHYs on SC8280XP can be used in 4-lane mode or as separate controllers and PHYs in 2-lane mode (e.g. as PCIe2A and PCIe2B). Add support for fetching the 4-lane configuration from the TCSR and programming the lane registers of the second port when in 4-lane mode. Reviewed-by:
-
Johan Hovold authored
Add support for the single and dual-lane PHYs found on SC8280XP. Note that the SC8280XP binding does not try to describe every register subregion and instead the driver holds the corresponding offsets. Reviewed-by:
-
Johan Hovold authored
Some QMP PHYs have a second fixed-divider pipe clock that needs to be enabled along with the pipe clock. Add support for an optional "pipediv2" clock. Reviewed-by:
-
Johan Hovold authored
Add the missing delay after asserting reset. This is specifically needed for the reset to have any effect on SC8280XP. The vendor driver uses a 1 ms delay, but that seems a bit excessive. Instead use a 200 us delay which appears to be more than enough and also matches the UFS reset delay added by commit 870b1279 ("scsi: ufs-qcom: Add reset control support for host controller"). Reviewed-by:
-
Johan Hovold authored
In preparation for supporting devicetree bindings which do not use a child node, move the PHY creation to probe() proper and parse the serdes resource in what is now the legacy devicetree helper. Reviewed-by:
-
Johan Hovold authored
Add bindings for the PCIe QMP PHYs found on SC8280XP. The PCIe2 and PCIe3 controllers and PHYs on SC8280XP can be used in 4-lane mode or as separate controllers and PHYs in 2-lane mode (e.g. as PCIe2A and PCIe2B). The configuration for a specific system can be read from a TCSR register. Reviewed-by:
-
Johan Hovold authored
The current QMP PCIe PHY bindings are based on the original MSM8996 binding which provided multiple PHYs per IP block and these in turn were described by child nodes. Later QMP PCIe PHY blocks only provide a single PHY and the remnant child node does not really reflect the hardware. The original MSM8996 binding also ended up describing the individual register blocks as belonging to either the wrapper node or the PHY child nodes. This is an unnecessary level of detail which has lead to problems when later IP blocks using different register layouts have been forced to fit the original mould rather than updating the binding. The bindings are arguable also incomplete as they only the describe register blocks used by the current Linux drivers (e.g. does not include the per lane PCS registers). In preparation for adding new bindings for SC8280XP which further bindings can be based on, rename the current schema file after IPQ8074, which was the first SoC added to the bindings after MSM8996 (which has already been split out), and add a reference to the SC8280XP bindings. Reviewed-by:
-
