Fix a typo in the comment for the TOSHIBA_RBTX4939 config option
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In file included from include/linux/ptrace.h:49,
                 from arch/mips/kernel/kgdb.c:25:
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:123: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:124: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:126: error: expected declaration specifiers or '...' before '__u32'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:127: error: expected declaration specifiers or '...' before '__u32'
make[1]: *** [arch/mips/kernel/kgdb.o] Error 1
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The following functions

disable_local1_irq()
disable_local2_irq()
disable_local3_irq()

are needlessly defined global, so make them static. While at it, fix a
whitespace error in the same file.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add smc91x platform device to RBTX4939 board and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add sysfs interface for 7 segment LED and implement access routine for
RBTX4939.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

mips/pci/fixup-rc32434.c must #include <asm/mach-rc32434/irq.h>

This patch fixes the following compile error caused by
commit 606a083b
(MIPS: RB532: Cleanup the headers again):

<--  snip  -->

...
  CC      arch/mips/pci/fixup-rc32434.o
arch/mips/pci/fixup-rc32434.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-rc32434.c:46: error: 'GROUP4_IRQ_BASE' undeclared (first use in this function)
arch/mips/pci/fixup-rc32434.c:46: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-rc32434.c:46: error: for each function it appears in.)
make[2]: *** [arch/mips/pci/fixup-rc32434.o] Error 1

<--  snip  -->

A virtually identical patch was also submitted by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

<asm/ptrace.h> is exported to userland so can't include <linux/ptrace.h>,
so replace the C99 types with their basic C type equivalents.

Bug originally reported and initial patch by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Noticed by Anirban Sinha <ASinha@zeugmasystems.com>; patch by me.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We were getting away with this for so long only because the only platform
with a non-empty plat_unmap_dma_mem() doesn't call dma_sync_sg_for_cpu()
and dma_sync_sg_for_device() from its commonly used drivers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

debugfs_create_*() returns NULL on error.  Make its callers return -ENODEV
on error.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

debugfs_create_*() returns NULL on error.  Make its caller debugfs_fpuemu
return -ENODEV on error.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* 'for-linus' of git://neil.brown.name/md:
  md: allow extended partitions on md devices.
  md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
  md: use sysfs_notify_dirent to notify changes to md/array_state

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - add support for Elantech touchpads
  Input: i8042 - add Blue FB5601 to noloop exception table

* 'for-linus' of git://git.o-hand.com/linux-mfd:
  mfd: Make WM8400 depend on I2C until SPI is submitted
  mfd: add missing Kconfig entry for da903x

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
  uwb: build UWB before USB/WUSB

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Add support for Sony Vaio VGX-TP1E
  HID: fix lock imbalance in hiddev
  HID: fix lock imbalance in hidraw
  HID: fix hidbus/appletouch device binding regression
  HID: add hid_type to general hid struct
  HID: quirk for OLED devices present in ASUS G50/G70/G71
  HID: Remove "default m" for Thrustmaster and Zeroplus
  HID: fix hidraw_exit section mismatch
  HID: add support for another Gyration remote control
  Revert "HID: Invert HWHEEL mappings for some Logitech mice"

Fix docbook fatal errors (file location changed):

docproc: lin2628-rc1/include/asm-x86/io_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/deviceiobook.xml] Error 1

docproc: lin2628-rc1/include/asm-x86/atomic_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/kernel-api.xml] Error 1

docproc: lin2628-rc1/include/asm-x86/mca_dma.h: No such file or directory
make[1]: *** [Documentation/DocBook/mcabook.xml] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Allow macros that are annotated with kernel-doc to contain whitespace
between the '#' and "define".  It's valid and being used, so allow it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  leds-hp-disk: fix build warning
  ACPI: Oops in ACPI with git latest
  ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
  toshiba_acpi: always call input_sync() after input_report_switch()
  ACPI: Always report a sync event after a lid state change
  ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
  i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
  i7300_idle: Cleanup based review comments
  i7300_idle: Disable ioat channel only on platforms where ile driver can load

.. fix all the worst problems in -rc1

If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:

| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used

because console_initcall() is not defined (nor really sensible) in the
modular case.

So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit f337b9c5 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events().  The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test.  Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.

HOWEVER.

The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).

In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items.  The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".

This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select().  The old kernels accepted this just
fine, so the new kernels must too.

However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.

This patch fixes this by adding the excess microseconds to the seconds
field.

Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...

Change the default to "y" and also adjust the config text a little to
reflect this.

This patch fixes regression #11859

With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'

Introduced in commit cc31edce "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
  hwmon: (abituguru3) Cosmetic whitespace fixes
  hwmon: (adt7473) Fix voltage conversion routines
  hwmon: (lm90) Add support for the LM99 16 degree offset
  hwmon: (lm90) Fix handling of hysteresis value
  hwmon-vid: Add support for AMD family 10h CPUs
  hwmon: (w83781d) Fix linking when built-in

This reverts commit 7bf6bf48.

The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1.  It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.

Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.

Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.

What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.

Solution: use sym_clear_all_valid() in there.  Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.

[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.

Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.

Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.

According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>

The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>

There are several problems in the way the hysteresis value is handled
by the lm90 driver:

* In show_temphyst(), specific handling of the MAX6646 is missing, so
  the hysteresis is reported incorrectly if the critical temperature
  is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
  the chip but data->temp_hyst isn't updated accordingly, so there is
  a short period of time (up to 2 seconds) where the old hystereris
  value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
  to compute the value of the hysteresis register lacks
  device-specific handling. As a result, the value of the hysteresis
  register might be incorrect for the ADT7461 and MAX6646 chips.

Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>