Remove ehea_error, ehea_info and ehea_debug macros.
Use pr_fmt, pr_<level>, netdev_<level> and netif_<level> as appropriate.
Fix messages to use trailing "\n", some messages had an extra one
as the old ehea_<level> macros added a trailing "\n".
Coalesced long format strings.

Uncompiled/untested.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch provides USB CDC NCM host driver support in the Linux Kernel.

Changes:
drivers/net/usb/cdc_ncm.c:
- initial submission of the CDC NCM host driver;
- verified on Intel 32/64 bit, Intel Atom, ST-Ericsson U8500 (ARM)
- throughput measured over 100 Mbits duplex;
- driver supports 16-bit NTB format only, but it is more than enough for
  transfers up to 64K;
- driver can handle up to 32 datagrams in received NTB;
- timer is used to collect several packets in Tx direction

drivers/net/usb/Kconfig:
- a new entry to compile CDC NCM host driver
drivers/net/usb/Makefile:
- a new entry to compile CDC NCM host driver
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes:
include/linux/usb/usbnet.h:
- a new flag to indicate driver's capability to accumulate IP packets in Tx
 direction and extract several packets from single skb in Rx direction.
drivers/net/usb/usbnet.c:
- the procedure of counting packets in usbnet was updated due to the
 accumulating of IP packets in the driver
- no short packets are sent if indicated by the flag in driver_info
 structure
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the tg3 version to 3.116.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hardware defaults to fairly aggressive EEE thresholds.  While there
appear to be no ill effects, this patch relaxes them, just as a
precaution.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first hunk of this patch makes sure that the driver checks for the
appropriate preconditions before checking if EEE negotiation succeeded.
More specifically the link needs to be full duplex for EEE to be
enabled.

The second and third hunks of this patch fix a bug where the eee
advertisement register would be programmed with extra bits set.

The fourth hunk of this patch makes sure the EEE capability flag is not
set for 5718 A0 devices and that the device is not a serdes device.

None of these modifications are strictly necessary.  The driver /
hardware still does the right thing.  They are submitted primarily for
correctness.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EEE support in the 57765 internal phy will not enable after a phy reset
unless it sees that EEE is supported in the MAC.  This patch moves the
code that programs the CPMU EEE registers to a place before the phy
reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 52b02d04 entitled "tg3: Add
EEE support", Ben Hutchings had commented that the EEE advertisement
register will be in a standard location.  This patch moves that
definition into mdio.h and changes the code to use it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current transmit routines set the jumbo frame BD flag too
aggressively.  This can reduce performance for common cases.  This patch
raises the jumbo flag threshold to 1518, up from 1500.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb head being allocated by kmalloc(), it might be larger than what
actually requested because of discrete kmem caches sizes. Before
reallocating a new skb head, check if the current one has the needed
extra size.

Do this check only if skb head is not shared.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new PBA format is stored as a string.  This patch allows the
driver to support both the old and new format.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add both NIC and backplane support for FCoE enabled devices IDs.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch will add wake on LAN support to the dev/sub_dev 10FB 11A9.  This
will also include ixgbe ethtool support for this device.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have had several requests to have ifconfig down command disable
the SFP+ laser and thus make link go down.  Likewise on ifconfig up
the laser would be enabled and link would come up.  This patch enables
that behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently driver set default eswitch configuration values for PF function,
instead of validating values sent by application.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Loopback mode can not be supported in CNA mode. Removing it until FW is fixed.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some reason we failed to make this change when perm_addr was
introduced.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only have direct access to MDIO on Falcon, so move this out of
struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only have direct access to SPI on Falcon, so move all this state
out of struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool EEPROM interface is really meant for exposing chip
configuration, not BootROM configuration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the Falcon board config is invalid, we cannot proceed - we do not
have a valid board type to pass to falcon_probe_board(), and if we
kluge that to work with an unknown board then other initialisation
code will crash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always
sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we
could guarantee to be able to implement this on future hardware.

Given this, I'm less convinced that the protocol should be changed.

To reiterate the failure mode: The driver sees this:

 issue command
 receive REBOOT event

Was that reboot event sent before the command was issued, or in
response to the command? If the former then there will be a subsequent
CMDDONE event, if the latter, then there will be no CMDDONE event.

Options to resolve this are:

 1. REBOOT always completes an outstanding mcdi request, and we set
    the credits count to ignore a subsequent CMDDONE event with
    mismatching seqno.

 2. REBOOT never completes an outstanding mcdi request. If there is
    no CMDDONE event then we rely on the mcdi timeout code to complete
    the outstanding request, incurring a 10s delay.

I'd argue that (2) is tidier, but that incurring a 10s delay is a little
needless. Let's go with (1).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we enable PMA/PMD loopback this automatically sets RXIN_SEL
(inverse polarity for RXIN).  We need to clear that bit during the
soft-reset sequence, as it is not done automatically.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We do not want to shut down the board based on a fault that has
already been cleared.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set both the 'maximum' and critical temperature limits for LM87
hardware monitors on Falcon boards.  Do not shut down a port until the
critical temperature is reached, but warn as soon as the 'maximum'
temperature is reached.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some errors are expected, e.g. when sending new commands to an MC
running old firmware.  Only the caller of efx_mcdi_rpc() can decide
what is a real error.  Therefore log the error responses with
netif_dbg().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moves the content of the native API routine tipc_ownidentity() into the
sole routine that calls it, since it can no longer be called in isolation.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Moves the content of each native API message forwarding routine
into the sole routine that calls it, since the forwarding routines
no longer be called in isolation. Also removes code in each routine
that altered the outgoing message's importance level since this is
now no longer possible.

The previous function mapping (parent function, and child API) was
as follows:

   tipc_send2name
       \--tipc_forward2name

   tipc_send2port
       \--tipc_forward2port

   tipc_send_buf2port
       \--tipc_forward_buf2port

After this commit, the children don't exist and their functionality
is completely in the respective parent.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes a symbol that is not referenced anywhere by TIPC's link code.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removes initialization of a local variable that is always assigned
a different value before it is referenced.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>