Link Power Management (LPM) on STM32MP15 OTG HS encounters instabilities
with some Host controllers. OTG core fails to exit L1 state in 200us:
"dwc2 49000000.usb-otg: Failed to exit L1 sleep state in 200us."
Then the device is still not enumerated.

To avoid this issue, disable Link Power Management on STM32MP15 HS OTG.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-4-amelie.delaunay@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the core is in FS host mode, using the FS transceiver, and a Low-Speed
device is connected, transceiver clock is 6Mhz.
So, to support Low-Speed devices, enable support of FS/LS Low Power mode,
so that the PHY supplies a 6 MHz clock during Low-Speed mode.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-3-amelie.delaunay@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

STM32MP15 ahbcfg register default value sets Burst length/type (HBSTLEN)
to Single (32-bit accesses on AHB), which is not recommended, according
to STM32MP157 Reference manual [1].
This patch sets Burst length/type (HBSTLEN) so that bus transactions
target 16x32 bit accesses. This improves OTG controller performance.

[1] https://www.st.com/resource/en/reference_manual/dm00327659.pdf, p.3149
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105094855.30763-2-amelie.delaunay@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently a tasklet is used to transmit input substream buffer
data. However, tasklets have long been deprecated as being too
heavy on the system by running in irq context - and this is not
a performance critical path. If a higher priority process wants
to run, it must wait for the tasklet to finish before doing so.

Deferring work to a workqueue and executing in process context
should be fine considering the callback already does
f_midi_do_transmit() under the transmit_lock and thus changes in
semantics are ok regarding concurrency - tasklets being serialized
against itself.

Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Link: https://lore.kernel.org/r/20210111042855.73289-1-dave@stgolabs.netSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210111135458.57084-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210111135539.57234-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For some UDCs, the initialization sequence by udc_start() should not be
repeated until it is properly cleaned up with udc_stop() and vise versa.
We may run into some cleanup failure as seen with the DWC3 driver during
the irq cleanup. This issue can occur when the user triggers
soft-connect/soft-disconnect from the soft_connect sysfs. To avoid
adding checks to every UDC driver, at the UDC framework, introduce a
"started" state to track and prevent the UDC from repeating the
udc_start() and udc_stop() if it had already started/stopped.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/a7c4112fcd4dc2f0169af94a24f5685ca77f09fd.1610395599.git.Thinh.Nguyen@synopsys.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_reset_control_array_get_optional_shared() looks more readable
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Link: https://lore.kernel.org/r/1604375863-6649-1-git-send-email-yejune.deng@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Keem Bay DWC3 compatible DT nodes are supposed to have a DWC USB3
compatible sub-node to describe a fully functioning USB interface. Let's
use the available DWC USB3 DT schema to validate the Intel Keem Bay DWC3
sub-nodes.

Note since the generic DWC USB3 DT node is supposed to be named as generic
USB HCD ("^usb(@.*)?") one we have to accordingly fix the sub-nodes name
regexp and fix the DT node example.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-20-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Qualcomm msm8996/sc7180/sdm845 DWC3 compatible DT nodes are supposed to
have a DWC USB3 compatible sub-node to describe a fully functioning USB
interface. Let's use the available DWC USB3 DT schema to validate the
Qualcomm DWC3 sub-nodes.

Note since the generic DWC USB3 DT node is supposed to be named as generic
USB HCD ("^usb(@.*)?") one we have to accordingly fix the sub-nodes name
regexp and fix the DT node example.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-19-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TI Keystone DWC3 compatible DT node is supposed to have a DWC USB3
compatible sub-node to describe a fully functioning USB interface.
Since DWC USB3 has now got a DT schema describing its DT node, let's make
sure the TI Keystone DWC3 sub-node passes validation against it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-18-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Amlogic G12A USB DT sub-nodes are supposed to be compatible with the
generic DWC USB2 and USB3 devices. Since now we've got DT schemas for
both of the later IP cores let's make sure that the Amlogic G12A USB
DT nodes are fully evaluated including the DWC sub-nodes.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-17-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

An empty snps,quirk-frame-length-adjustment won't cause any change
performed by the driver. Moreover the DT schema validation will fail,
since it expects the property being assigned with some value. So set
fix the example by setting a valid FL-adj value in accordance with
Neil Armstrong comment.

Link: https://lore.kernel.org/linux-usb/20201010224121.12672-16-Sergey.Semin@baikalelectronics.ru/Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-16-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In accordance with the IP core databook the
snps,quirk-frame-length-adjustment property can be set within [0, 0x3F].
Let's make sure the DT schema applies a correct constraints on the
property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-15-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In accordance with the driver comments the PIPE3 de-emphasis can be tuned
to be either -6dB, -2.5dB or disabled. Let's add the de-emphasis
property constraints so the DT schema would make sure the controller DT
node is equipped with correct value.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-14-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DWC USB3 driver and some DTS files like Exynos 5250, Keystone k2e, etc
expects the DWC USB3 DT node to have the compatible string with the
"synopsys" vendor prefix. Let's add the corresponding compatible string to
the controller DT schema, but mark it as deprecated seeing the Synopsys,
Inc. is presented with just "snps" vendor prefix.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-13-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The controller driver supports two types of DWC USB3 devices: with a
common interrupt lane and with individual interrupts for each mode. Add
support for both these cases to the DWC USB3 DT schema.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-12-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

DWC USB3 DT node is supposed to be compliant with the Generic xHCI
Controller schema, but with additional vendor-specific properties, the
controller-specific reference clocks and PHYs. So let's convert the
currently available legacy text-based DWC USB3 bindings to the DT schema
and make sure the DWC USB3 nodes are also validated against the
usb-xhci.yaml schema.

Note 1. we have to discard the nodename restriction of being prefixed with
"dwc3@" string, since in accordance with the usb-hcd.yaml schema USB nodes
are supposed to be named as "^usb(@.*)".

Note 2. The clock-related properties are marked as optional to match the
DWC USB3 driver expectation and to improve the bindings mainainability
so in case if there is a glue-node it would the responsible for the
clocks initialization.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-11-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With minor peculiarities (like uploading some vendor-specific firmware)
these are just Generic xHCI controllers fully compatible with its
properties. Make sure the Renesas USB xHCI DT nodes are also validated
against the Generic xHCI DT schema.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-10-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For some reason the "brcm,xhci-brcm-v2" compatible string has been missing
in the original bindings file. Add it to the Generic xHCI Controllers DT
schema since the controller driver expects it to be supported.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-9-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the DT bindings of Generic xHCI Controllers are described by
means of the legacy text file. Since such format is deprecated in favor of
the DT schema, let's convert the Generic xHCI Controllers bindings file to
the corresponding yaml files. There will be two of them: a DT schema for
the xHCI controllers on a generic platform and a DT schema validating a
generic xHCI controllers properties. The later will be used to validate
the xHCI controllers, which aside from some vendor-specific features
support the basic xHCI functionality.

An xHCI-compatible DT node shall support the standard USB HCD properties
and custom ones like: usb2-lpm-disable, usb3-lpm-capable,
quirk-broken-port-ped and imod-interval-ns. In addition if a generic xHCI
controller is being validated against the DT schema it is also supposed to
be equipped with mandatory compatible string, single registers range,
single interrupts source, and is supposed to optionally contain up to two
reference clocks for the controller core and CSRs.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-8-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Even though the Generic PHY framework is the more preferable way of
setting the USB PHY up, there are still many dts-files and DT bindings
which rely on having the legacy "usb-phy" specified to attach particular
USB PHYs to USB cores. Let's have the "usb-phy" property described in
the generic USB HCD binding file so it would be validated against the
nodes in which it's specified. Mark the property as deprecated to
discourage the developers from using it.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-7-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The host controller device might be designed to work for the particular
products or applications. In that case its DT node is supposed to be
equipped with the tpl-support property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-6-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Aside from the UTMI+ there are also ULPI, Serial and HSIC PHY types
that can be specified in the phy_type HCD property. Add them to the
enumeration of the acceptable values.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-5-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There are only four OTG revisions are currently supported by the kernel:
0x0100, 0x0120, 0x0130, 0x0200. Any another value is considered as
invalid.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-4-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The generic USB properties have been described in the legacy bindings
text file: Documentation/devicetree/bindings/usb/generic.txt . Let's
convert its content into the generic USB, USB HCD and USB DRD DT
schemas. So the Generic USB schema will be applicable to all USB
controllers, USB HCD - for the generic USB Host controllers and the USB
DRD - for the USB Dual-role controllers.

Note the USB DRD schema is supposed to work in conjunction with
the USB peripheral/gadget and USB host controllers DT schemas.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-3-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There can be three distinctive types of the USB controllers: USB hosts,
USB peripherals/gadgets and USB OTG, which can switch from one role to
another. In order to have that hierarchy handled in the DT binding files,
we need to collect common properties in a common DT schema and specific
properties in dedicated schemas. Seeing the usb-hcd.yaml DT schema is
dedicated for the USB host controllers only, let's move some common
properties from there into the usb.yaml schema. So the later would be
available to evaluate all currently supported types of the USB
controllers.

While at it add an explicit "additionalProperties: true" into the
usb-hcd.yaml as setting the additionalProperties/unevaluateProperties
properties is going to be get mandatory soon.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201210090944.16283-2-Sergey.Semin@baikalelectronics.ruSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolves a merge issue in:
	drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Search for <ncurses.h> in the default header path of HOSTCC

 - Tweak the option order to be kind to old BSD awk

 - Remove 'kvmconfig' and 'xenconfig' shorthands

 - Fix documentation

* tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Documentation: kbuild: Fix section reference
  kconfig: remove 'kvmconfig' and 'xenconfig' shorthands
  lib/raid6: Let $(UNROLL) rules work with macOS userland
  kconfig: Support building mconf with vendor sysroot ncurses
  kconfig: config script: add a little user help
  MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal

Pull SCSI fixes from James Bottomley:
 "This is two driver fixes (megaraid_sas and hisi_sas).

  The megaraid one is a revert of a previous revert of a cpu hotplug fix
  which exposed a bug in the block layer which has been fixed in this
  merge window.

  The hisi_sas performance enhancement comes from switching to interrupt
  managed completion queues, which depended on the addition of
  devm_platform_get_irqs_affinity() which is now upstream via the irq
  tree in the last merge window"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: hisi_sas: Expose HW queues for v2 hw
  Revert "Revert "scsi: megaraid_sas: Added support for shared host tagset for cpuhotplug""

Pull block fixes from Jens Axboe:

 - Missing CRC32 selections (Arnd)

 - Fix for a merge window regression with bdev inode init (Christoph)

 - bcache fixes

 - rnbd fixes

 - NVMe pull request from Christoph:
    - fix a race in the nvme-tcp send code (Sagi Grimberg)
    - fix a list corruption in an nvme-rdma error path (Israel Rukshin)
    - avoid a possible double fetch in nvme-pci (Lalithambika Krishnakumar)
    - add the susystem NQN quirk for a Samsung driver (Gopal Tiwari)
    - fix two compiler warnings in nvme-fcloop (James Smart)
    - don't call sleeping functions from irq context in nvme-fc (James Smart)
    - remove an unused argument (Max Gurtovoy)
    - remove unused exports (Minwoo Im)

 - Use-after-free fix for partition iteration (Ming)

 - Missing blk-mq debugfs flag annotation (John)

 - Bdev freeze regression fix (Satya)

 - blk-iocost NULL pointer deref fix (Tejun)

* tag 'block-5.11-2021-01-10' of git://git.kernel.dk/linux-block: (26 commits)
  bcache: set bcache device into read-only mode for BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET
  bcache: introduce BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE for large bucket
  bcache: check unsupported feature sets for bcache register
  bcache: fix typo from SUUP to SUPP in features.h
  bcache: set pdev_set_uuid before scond loop iteration
  blk-mq-debugfs: Add decode for BLK_MQ_F_TAG_HCTX_SHARED
  block/rnbd-clt: avoid module unload race with close confirmation
  block/rnbd: Adding name to the Contributors List
  block/rnbd-clt: Fix sg table use after free
  block/rnbd-srv: Fix use after free in rnbd_srv_sess_dev_force_close
  block/rnbd: Select SG_POOL for RNBD_CLIENT
  block: pre-initialize struct block_device in bdev_alloc_inode
  fs: Fix freeze_bdev()/thaw_bdev() accounting of bd_fsfreeze_sb
  nvme: remove the unused status argument from nvme_trace_bio_complete
  nvmet-rdma: Fix list_del corruption on queue establishment failure
  nvme: unexport functions with no external caller
  nvme: avoid possible double fetch in handling CQE
  nvme-tcp: Fix possible race of io_work and direct send
  nvme-pci: mark Samsung PM1725a as IGNORE_DEV_SUBNQN
  nvme-fcloop: Fix sscanf type and list_first_entry_or_null warnings
  ...

Pull io_uring fixes from Jens Axboe:
 "A bit larger than I had hoped at this point, but it's all changes that
  will be directed towards stable anyway. In detail:

   - Fix a merge window regression on error return (Matthew)

   - Remove useless variable declaration/assignment (Ye Bin)

   - IOPOLL fixes (Pavel)

   - Exit and cancelation fixes (Pavel)

   - fasync lockdep complaint fix (Pavel)

   - Ensure SQPOLL is synchronized with creator life time (Pavel)"

* tag 'io_uring-5.11-2021-01-10' of git://git.kernel.dk/linux-block:
  io_uring: stop SQPOLL submit on creator's death
  io_uring: add warn_once for io_uring_flush()
  io_uring: inline io_uring_attempt_task_drop()
  io_uring: io_rw_reissue lockdep annotations
  io_uring: synchronise ev_posted() with waitqueues
  io_uring: dont kill fasync under completion_lock
  io_uring: trigger eventfd for IOPOLL
  io_uring: Fix return value from alloc_fixed_file_ref_node
  io_uring: Delete useless variable ‘id’ in io_prep_async_work
  io_uring: cancel more aggressively in exit_work
  io_uring: drop file refs after task cancel
  io_uring: patch up IOPOLL overflow_flush sync
  io_uring: synchronise IOPOLL on task_submit fail

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 5.11-rc3.

  Include in here are:

   - USB gadget driver fixes for reported issues

   - new usb-serial driver ids

   - dma from stack bugfixes

   - typec bugfixes

   - dwc3 bugfixes

   - xhci driver bugfixes

   - other small misc usb driver bugfixes

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
  usb: dwc3: gadget: Clear wait flag on dequeue
  usb: typec: Send uevent for num_altmodes update
  usb: typec: Fix copy paste error for NVIDIA alt-mode description
  usb: gadget: enable super speed plus
  kcov, usb: hide in_serving_softirq checks in __usb_hcd_giveback_urb
  usb: uas: Add PNY USB Portable SSD to unusual_uas
  usb: gadget: configfs: Preserve function ordering after bind failure
  usb: gadget: select CONFIG_CRC32
  usb: gadget: core: change the comment for usb_gadget_connect
  usb: gadget: configfs: Fix use-after-free issue with udc_name
  usb: dwc3: gadget: Restart DWC3 gadget when enabling pullup
  usb: usbip: vhci_hcd: protect shift size
  USB: usblp: fix DMA to stack
  USB: serial: iuu_phoenix: fix DMA from stack
  USB: serial: option: add LongSung M5710 module support
  USB: serial: option: add Quectel EM160R-GL
  USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug
  usb: gadget: f_uac2: reset wMaxPacketSize
  usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression
  usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based one
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.11-rc3. Nothing major,
  just resolving some reported issues:

   - cleanup some remaining mentions of the ION drivers that were
     removed in 5.11-rc1

   - comedi driver bugfix

   - two error path memory leak fixes

  All have been in linux-next for a while with no reported issues"

* tag 'staging-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ION: remove some references to CONFIG_ION
  staging: mt7621-dma: Fix a resource leak in an error handling path
  Staging: comedi: Return -EFAULT if copy_to_user() fails
  staging: spmi: hisi-spmi-controller: Fix some error handling paths

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.11-rc3.

  The majority here are fixes for the habanalabs drivers, but also in
  here are:

   - crypto driver fix

   - pvpanic driver fix

   - updated font file

   - interconnect driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
  Fonts: font_ter16x32: Update font with new upstream Terminus release
  misc: pvpanic: Check devm_ioport_map() for NULL
  speakup: Add github repository URL and bug tracker
  MAINTAINERS: Update Georgi's email address
  crypto: asym_tpm: correct zero out potential secrets
  habanalabs: Fix memleak in hl_device_reset
  interconnect: imx8mq: Use icc_sync_state
  interconnect: imx: Remove a useless test
  interconnect: imx: Add a missing of_node_put after of_device_is_available
  interconnect: qcom: fix rpmh link failures
  habanalabs: fix order of status check
  habanalabs: register to pci shutdown callback
  habanalabs: add validation cs counter, fix misplaced counters
  habanalabs/gaudi: retry loading TPC f/w on -EINTR
  habanalabs: adjust pci controller init to new firmware
  habanalabs: update comment in hl_boot_if.h
  habanalabs/gaudi: enhance reset message
  habanalabs: full FW hard reset support
  habanalabs/gaudi: disable CGM at HW initialization
  habanalabs: Revise comment to align with mirror list name
  ...

Section 3.11 was incorrectly called 3.9, fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Pull ARC fixes from Vineet Gupta:

 - Address the 2nd boot failure due to snafu in signal handling code
   (first was generic console ttynull issue)

 - misc other fixes

* tag 'arc-5.11-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [hsdk]: Enable FPU_SAVE_RESTORE
  ARC: unbork 5.11 bootup: fix snafu in _TIF_NOTIFY_SIGNAL handling
  include/soc: remove headers for EZChip NPS
  arch/arc: add copy_user_page() to <asm/page.h> to fix build error on ARC

Pull powerpc fixes from Michael Ellerman:

 - A fix for machine check handling with VMAP stack on 32-bit.

 - A clang build fix.

Thanks to Christophe Leroy and Nathan Chancellor.

* tag 'powerpc-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Handle .text.{hot,unlikely}.* in linker script
  powerpc/32s: Fix RTAS machine check with VMAP stack

Pull x86 fixes from Borislav Petkov:
 "As expected, fixes started trickling in after the holidays so here is
  the accumulated pile of x86 fixes for 5.11:

   - A fix for fanotify_mark() missing the conversion of x86_32 native
     syscalls which take 64-bit arguments to the compat handlers due to
     former having a general compat handler. (Brian Gerst)

   - Add a forgotten pmd page destructor call to pud_free_pmd_page()
     where a pmd page is freed. (Dan Williams)

   - Make IN/OUT insns with an u8 immediate port operand handling for
     SEV-ES guests more precise by using only the single port byte and
     not the whole s32 value of the insn decoder. (Peter Gonda)

   - Correct a straddling end range check before returning the proper
     MTRR type, when the end address is the same as top of memory.
     (Ying-Tsun Huang)

   - Change PQR_ASSOC MSR update scheme when moving a task to a resctrl
     resource group to avoid significant performance overhead with some
     resctrl workloads. (Fenghua Yu)

   - Avoid the actual task move overhead when the task is already in the
     resource group. (Fenghua Yu)"

* tag 'x86_urgent_for_v5.11_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Don't move a task to the same resource group
  x86/resctrl: Use an IPI instead of task_work_add() to update PQR_ASSOC MSR
  x86/mtrr: Correct the range check before performing MTRR type lookups
  x86/sev-es: Fix SEV-ES OUT/IN immediate opcode vc handling
  x86/mm: Fix leak of pmd ptlock
  fanotify: Fix sys_fanotify_mark() on native x86-32