- 10 Mar, 2016 40 commits
-
-
Jes Sorensen authored
Provide RF_T_METER register location for nextgen chips. Signed-off-by:
Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Jes Sorensen authored
Vendor driver implements this for 8723b and 8821 series Signed-off-by:
-
Jes Sorensen authored
Keep the automated tools happy Signed-off-by:
-
Jes Sorensen authored
This initializes RX DMA aggregation on 8723bu. We should do this for all parts eventually, and also init TX aggregation. Signed-off-by:
-
Jes Sorensen authored
Group chip quirks together instead of having them scattered all over in the init code. Signed-off-by:
-
Jes Sorensen authored
List yet another new register found on the 8723b. Signed-off-by:
-
Jes Sorensen authored
Set PHY lock after running the RF init sequence on 8723bu. Signed-off-by:
-
Jes Sorensen authored
Having a version for the newer chips without calling it doesn't do much good..... Signed-off-by:
-
Jes Sorensen authored
Implement burst parameter sequence for 8723bu parts. Eventually this should be moved into device specific sections. Signed-off-by:
-
Jes Sorensen authored
Set the correct TRXFF boundary for 8723bu. Signed-off-by:
-
Jes Sorensen authored
The vendor driver does not set FPGA0_TX_INFO here. In additiona the 8723bu can handler a larger PBP page size. Signed-off-by:
-
Jes Sorensen authored
Reorganize the init sequence in order to be able to compare to the 8723bu vendor driver's init sequence. Signed-off-by:
-
Jes Sorensen authored
Only apply the 80M spur hack for 8723au parts. Signed-off-by:
-
Jes Sorensen authored
In addition make register read/write flow match closer to vendor driver flow. This is mainly to be able to compare the register write log with the vendor driver, and can be optimized later once 8723bu support is working. Signed-off-by:
-
Jes Sorensen authored
No indication of what register 0xa3 does anywhere in the vendor source. Signed-off-by:
-
Jes Sorensen authored
This function is going to need to be split up into chip specific variants. Signed-off-by:
-
Jes Sorensen authored
Retrieve the XTAL_K value in the parse_efuse() functions as it's location various on a per device basis. For parts that do not provide an XTAL_K value, skip setting it. Signed-off-by:
-
Jes Sorensen authored
Additional tweaks to further map the init sequence for the 8723bu to that of the vendor driver. Signed-off-by:
-
Jes Sorensen authored
This matches the order of the 8723bu vendor driver Signed-off-by:
-
Jes Sorensen authored
This implements the 8723bu specific power on sequence as it is different from that of the 8723au chips. Signed-off-by:
-
Jes Sorensen authored
The 8723bu does not like REG_AFE_XTAL_CTRL being set, so skip this for now, to match the vendor driver. Signed-off-by:
-
Jes Sorensen authored
Issue a BT_INFO command to verify the status of BT/WiFi settings. Signed-off-by:
-
Jes Sorensen authored
8723bu BT registers are written via the mailbox interface. Add support for writing these and corresponding C2H event responses. Signed-off-by:
-
Jes Sorensen authored
The 64 bit mailbox commands also provide a different method for mailbox command responses (C2H events). Signed-off-by:
-
Jes Sorensen authored
This adds code to parse the new RX descriptor format used by the 8723bu/8192eu parts. Signed-off-by:
-
Jes Sorensen authored
The nextgen chips use a slightly different RX descriptor format. This adds support for the new format. Signed-off-by:
-
Jes Sorensen authored
Use the correct type when setting PS TDMA for 8723bu. This matches the vendor driver. Signed-off-by:
-
Jes Sorensen authored
The 8723bu is a WiFi/BT combo part. When initializing it for WiFi, make sure to tell it not to ignore WiFi activity. Signed-off-by:
-
Jes Sorensen authored
Implement additional init sequence code for the 8723bu. Signed-off-by:
-
Jes Sorensen authored
Remove an unused variable to make the compiler happy. Signed-off-by:
-
Jes Sorensen authored
This should initialize the antennas on the 8723bu, but so far I am still not receiving anything :( More work is needed. Signed-off-by:
-
Jes Sorensen authored
This is a first stab of implementing rtl8723bu_config_channel(). For now this will only do 20MHz channels. Signed-off-by:
-
Jakub Sitnicki authored
TX power values are laid out differently in EFUSE found in RTL8192EU & RTL8188EU devices. TX power indices and differences for each RF path are not interleaved (A, B, A, B), as in other chips, but follow one another (A, B, C, D). Signed-off-by:
Jakub Sitnicki <jsitnicki@gmail.com> Signed-off-by:
-
Jes Sorensen authored
This was inspired by the vendor driver, but in the end never used for anything. Signed-off-by:
-
Jes Sorensen authored
This matches the flow of the vendor driver for newer hardware, and doesn't seem to cause issues for the older parts. Signed-off-by:
-
Jes Sorensen authored
Newer chips (8723bu/8192eu) has S0S1 settings which needs to be dealt with during LC calibration. Signed-off-by:
-
Jes Sorensen authored
The 8723bu also has it's own IQK calibration process. This is similar in flow, but still different enough to warrent it's own implementation, at least for now. Signed-off-by:
-
Jes Sorensen authored
This adds some additional register definitions for 8723bu, as well as a bit define for USB RXDMA aggregation in REG_RXDMA_AGG_PG_TH. Signed-off-by:
-
Jes Sorensen authored
rtl8192cu/rtl8188cu/rtl8723au use the same values, but 8723bu and 8192eu have their own. Signed-off-by:
-
Jes Sorensen authored
Usual gcc i386 issue reported by kbuildbot Signed-off-by:
-
