- 09 Oct, 2019 16 commits
-
-
Colin Ian King authored
Don't populate the array interval on the stack but instead make it static. Makes the object code smaller by 121 bytes. Before: text data bss dec hex filename 167797 29676 448 197921 30521 wireless/intel/iwlegacy/common.o After: text data bss dec hex filename 167580 29772 448 197800 304a8 wireless/intel/iwlegacy/common.o (gcc version 9.2.1, amd64) Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Dan Carpenter authored
The WARN_ON() macro doesn't take an error message, the argument is a condition so this won't display the warning message. Fixes: 27e117e4 ("rtw88: add deep power save support") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Chris Chiu authored
The RTL8723BU suffers the wifi disconnection problem while bluetooth device connected. While wifi is doing tx/rx, the bluetooth will scan without results. This is due to the wifi and bluetooth share the same single antenna for RF communication and they need to have a mechanism to collaborate. BT information is provided via the packet sent from co-processor to host (C2H). It contains the status of BT but the rtl8723bu_handle_c2h dose not really handle it. And there's no bluetooth coexistence mechanism to deal with it. This commit adds a workqueue to set the tdma configurations and coefficient table per the parsed bluetooth link status and given wifi connection state. The tdma/coef table comes from the vendor driver code of the RTL8192EU and RTL8723BU. However, this commit is only for single antenna scenario which RTL8192EU is default dual antenna. The rtl8xxxu_parse_rxdesc24 which invokes the handle_c2h is only for 8723b and 8192e so the mechanism is expected to work on both chips with single antenna. Note RTL8192EU dual antenna is not supported. Signed-off-by:
Chris Chiu <chiu@endlessm.com> Signed-off-by:
Jes Sorensen <Jes.Sorensen@gmail.com> Signed-off-by:
-
Navid Emamdoost authored
In mwifiex_pcie_init_evt_ring, a new skb is allocated which should be released if mwifiex_map_pci_memory() fails. The release for skb and card->evtbd_ring_vbase is added. Fixes: 0732484b ("mwifiex: separate ring initialization and ring creation routines") Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by:
Ganapathi Bhat <gbhat@marvell.com> Signed-off-by:
-
Navid Emamdoost authored
In mwifiex_pcie_alloc_cmdrsp_buf, a new skb is allocated which should be released if mwifiex_map_pci_memory() fails. The release is added. Fixes: fc331460 ("mwifiex: use pci_alloc/free_consistent APIs for PCIe") Signed-off-by:
-
Johan Hovold authored
USB core will never call a USB-driver probe function with a NULL device-id pointer. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
This reverts commit f170d44b. USB core will never call a USB-driver probe function with a NULL device-id pointer. Reverting before removing the existing checks in order to document this and prevent the offending commit from being "autoselected" for stable. Signed-off-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8723com/fw_common.c: In function rtl8723_cmd_send_packet: drivers/net/wireless/realtek/rtlwifi/rtl8723com/fw_common.c:226:5: warning: variable own set but not used [-Wunused-but-set-variable] It is not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhengbin <zhengbin13@huawei.com> Signed-off-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c: In function btc8723b1ant_tdma_dur_adj_for_acl: drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c:1428:7: warning: variable wifi_busy set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c: In function btc8723b1ant_tdma_dur_adj_for_acl: drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c:1427:22: warning: variable bt_info_ext set but not used [-Wunused-but-set-variable] 'wifi_busy' is not used since commit 158707f9 ("rtlwifi: btcoex: Restore 23b 1ant routine for tdma adjustment") 'bt_info_ext' is not used since commit 2622d7d8 ("rtlwifi: btcoex: 23b 1ant: TDMA duration for ACL busy") Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8192e2ant.c: In function btc8192e2ant_tdma_duration_adjust: drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8192e2ant.c:1584:6: warning: variable result set but not used [-Wunused-but-set-variable] It is not used since commit 27a31a60 ("rtlwifi: btcoex: remove unused functions") Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c: In function rtl88e_dm_pwdb_monitor: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/dm.c:763:6: warning: variable h2c_parameter set but not used [-Wunused-but-set-variable] It is not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
-
zhengbin authored
rtlwifi: rtl8188ee: Remove set but not used variables 'v3','rtstatus','reg_ecc','reg_ec4','reg_eac','b_pathb_ok' Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function phy_config_bb_with_pghdr: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:652:22: warning: variable v3 set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function rtl88e_phy_config_rf_with_headerfile: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:772:7: warning: variable rtstatus set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function rtl88e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1945:6: warning: variable reg_ecc set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function rtl88e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1944:61: warning: variable reg_ec4 set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function rtl88e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1944:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c: In function rtl88e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/phy.c:1943:19: warning: variable b_pathb_ok set but not used [-Wunused-but-set-variable] They are not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c: In function rtl92c_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c:1373:6: warning: variable reg_ecc set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c: In function rtl92c_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8192c/phy_common.c:1372:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable] They are not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function rtl8723e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1346:6: warning: variable reg_ecc set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function rtl8723e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1345:61: warning: variable reg_ec4 set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function rtl8723e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1345:34: warning: variable reg_eac set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c: In function rtl8723e_phy_iq_calibrate: drivers/net/wireless/realtek/rtlwifi/rtl8723ae/phy.c:1344:19: warning: variable b_pathb_ok set but not used [-Wunused-but-set-variable] They are not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
-
zhengbin authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function rtl8812ae_phy_config_rf_with_headerfile: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:2079:7: warning: variable rtstatus set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function rtl8821ae_phy_config_rf_with_headerfile: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:2114:7: warning: variable rtstatus set but not used [-Wunused-but-set-variable] drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c: In function _rtl8812ae_phy_get_txpower_limit: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/phy.c:2354:6: warning: variable bd set but not used [-Wunused-but-set-variable] They are not used since commit f1d2b4d3 ("rtlwifi: rtl818x: Move drivers into new realtek directory") Reported-by:
-
Chris Chiu authored
We have 3 laptops which connect the wifi by the same RTL8723BU. The PCI VID/PID of the wifi chip is 10EC:B720 which is supported. They have the same problem with the in-kernel rtl8xxxu driver, the iperf (as a client to an ethernet-connected server) gets ~1Mbps. Nevertheless, the signal strength is reported as around -40dBm, which is quite good. From the wireshark capture, the tx rate for each data and qos data packet is only 1Mbps. Compare to the Realtek driver at https://github.com/lwfinger/rtl8723bu, the same iperf test gets ~12Mbps or better. The signal strength is reported similarly around -40dBm. That's why we want to improve. After reading the source code of the rtl8xxxu driver and Realtek's, the major difference is that Realtek's driver has a watchdog which will keep monitoring the signal quality and updating the rate mask just like the rtl8xxxu_gen2_update_rate_mask() does if signal quality changes. And this kind of watchdog also exists in rtlwifi driver of some specific chips, ex rtl8192ee, rtl8188ee, rtl8723ae, rtl8821ae...etc. They have the same member function named dm_watchdog and will invoke the corresponding dm_refresh_rate_adaptive_mask to adjust the tx rate mask. With this commit, the tx rate of each data and qos data packet will be 39Mbps (MCS4) with the 0xF00000 as the tx rate mask. The 20th bit to 23th bit means MCS4 to MCS7. It means that the firmware still picks the lowest rate from the rate mask and explains why the tx rate of data and qos data is always lowest 1Mbps because the default rate mask passed is always 0xFFFFFFF ranges from the basic CCK rate, OFDM rate, and MCS rate. However, with Realtek's driver, the tx rate observed from wireshark under the same condition is almost 65Mbps or 72Mbps, which indicating that rtl8xxxu could still be further improved. Signed-off-by:
Daniel Drake <drake@endlessm.com> Acked-by:
-
- 04 Oct, 2019 17 commits
-
-
Denis Efremov authored
The id pointer can be NULL in rsi_probe(). It is checked everywhere except for the else branch in the idProduct condition. The patch adds NULL check before the id dereference in the rsi_dbg() call. Fixes: 54fdb318 ("rsi: add new device model for 9116") Cc: Amitkumar Karwar <amitkarwar@gmail.com> Cc: Siva Rebbagondla <siva8118@gmail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Denis Efremov <efremov@linux.com> Signed-off-by:
-
Colin Ian King authored
The variable ret is being assigned a value that is never read and is being re-assigned a little later on. The assignment is redundant and hence can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: -
Chung-Hsien Hsu authored
The firmware may have SAE authentication code built-in. This is detected by the driver and indicated in the wiphy features flags. User-space can use this flag to determine whether or not to provide the password material for SAE authentication in the nl80211 CONNECT command. Signed-off-by:
Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by:
Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by:
-
Ping-Ke Shih authored
Disable efuse if the efuse is enabled when we failed to setup the efuse information, otherwise the hardware will not turn off. Fixes: e3037485 ("rtw88: new Realtek 802.11ac driver") Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
8822C is a 2x2 11ac chip, and then NSS must be less or equal to 2. However, current nss of hw cap is 3, likes hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=3 This commit adds constraint to make sure NSS <= rf_path_num, and result looks like hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=2 Fixes: e3037485 ("rtw88: new Realtek 802.11ac driver") Signed-off-by:
-
Ping-Ke Shih authored
This commit doesn't change logic at all, just use struct rtw_fw_hdr to access fixed part of 64 bytes header. Since remaining part is variable length data of actual firmware, we don't define them within the struct. Signed-off-by:
-
Yan-Hsuan Chuang authored
It's better to print firmware version at load time. But since we need to set debug_mask properly to default print rtw_dbg(), raise the debug level to rtw_info() instead. Also change the multiple line style to one line only, it will be easier for log analyzing. Signed-off-by:
-
Yan-Hsuan Chuang authored
Set CWmax/CWmin, TXOP and AIFS according to ieee80211_tx_queue_params. Do note that hardware has only one group of EDCA[ac] registers, if more than one vif are added, the EDCA[ac] registers will contain value of params of the most recent set by ieee80211_ops::conf_tx(). And AIFS = AIFSN[ac] * slot_time + SIFS, so if use_short_slot is changed, need to also change AIFS. Signed-off-by:
-
Ping-Ke Shih authored
The value of GET_RX_DESC_SWDEC() indicates that if this RX packet requires software decryption or not. And software decryption is required when the packet was encrypted and the hardware failed to decrypt it. So, GET_RX_DESC_SWDEC() is negative does not mean that this packet is decrypted, it might just have no encryption at all. To actually see if the packet is decrypted, driver needs to further check if the hardware has successfully decrypted it, with a specific type of encryption algorithm. Signed-off-by:
-
Yan-Hsuan Chuang authored
When downloading the reserved page, the first page always contains a beacon for the firmware to reference. For non-beaconing modes such as station mode, also put a blank skb with length=1. And for the beaconing modes, driver will get a real beacon with a length approximate to the page size. But as the beacon is always put at the first page, it does not need a tx_desc, because the TX path will generate one when TXing the reserved page to the hardware. So we could allocate a buffer with a size smaller than the reserved page, when using memcpy() to copy the content of reserved page to the buffer, the over-sized reserved page will violate the kernel memory. To fix it, add the tx_desc before memcpy() the reserved packets to the buffer, then we can get SKBs with correct length when counting the pages in total. And for page 0, count the extra tx_desc_sz that the TX path will generate. This way, the first beacon that allocated without tx_desc can be counted with the extra tx_desc_sz to get actual pages it requires. Fixes: e3037485 ("rtw88: new Realtek 802.11ac driver") Signed-off-by:
-
Yan-Hsuan Chuang authored
Sometimes mac80211 will ask us to flush the hardware queues. To flush them, first we need to get the corresponding priority queues from the RQPN mapping table. Then we can check the available pages are equal to the originally reserved pages, which means the hardware has returned all of the pages it used to transmit. Note that now we only check for 100 ms for the priority queue, but sometimes if we have a lot of traffic (ex. 100Mbps up), some of the packets could be dropped. Signed-off-by:
-
Yan-Hsuan Chuang authored
Based on the mac80211's TXQ implementation, TX-AMSDU can be used to get higher MAC efficiency. To make mac80211 aggregate MSDUs, low level driver just need to leave skbs in the TXQ, and mac80211 will try to aggregate them if possible. As driver will schedule a tasklet when the TX queue is woke, until the tasklet being served, there will have some skbs in the queue if traffic is heavy. Driver can control the max AMSDU size depending on the current bit rate used by hardware/firmware. The higher rates are used, the larger AMSDU size can be. It is tested that can achieve higher T-Put at higher rates. If the environment is relatively clean, and the bit_rate is high enough, we can get about 80Mbps improvement. For lower bit rates, not much gain can we get, so leave the max_amsdu length low to prevent aggregation. Signed-off-by:
-
Tzu-En Huang authored
Whenever the firmware increases/decreases the bit rate used to transmit to a peer, it sends an RA report through C2H to driver. Driver can then record the bit rate in the peer's struct rtw_sta_info, and report to mac80211 when it asks us for the statistics of the sta by ieee80211_ops::sta_statistics Signed-off-by:
Tzu-En Huang <tehuang@realtek.com> Signed-off-by:
-
Yan-Hsuan Chuang authored
We can indicate IEEE80211_HW_HAS_RATE_CONTROL to mac80211 because the hardware has its own rate control algorithm. And what driver needs to do is to choose an RA mask according the peer's capabilities. But the hardware is not able to setup BA session by itself. So driver requires to initiate tx BA session for hardware, and tells it if it is possible to transmit AMPDU. The hardware can then aggregate MPDUs. And the size of AMPDU is controlled by the TX descriptor and the register value. Since the TX descriptor will reference the max AMPDU size from ieee80211_sta::ht_cap::ampdu_factor, just set the register value to 0x3f, and let it be controlled by TX descriptor. Signed-off-by:
-
Yan-Hsuan Chuang authored
The mac80211 provides software TX queue for driver, as long as driver has hooked ieee80211_ops::wake_tx_queue. Each time a packet is queued onto the TX queue, that queue will be woken up the inform driver to serve the queue. Now driver only supports PCI interface ICs, there's no specific traffic control for each queue, just schedule a tasklet, and dump all of the packets at once to the DMA ring. Instead of TX the packets whenever TX queue is woke, tasklet handler can have more packets dumped to the device, takes advantage of burst write with DMA engine. And if the driver is going to support USB/SDIO ICs, the tasklet can be more flexible for aggregating the packets, enhance the efficiency of bandwidth usage. Signed-off-by:
-
Yan-Hsuan Chuang authored
Allows driver to send RTS by filling tx descriptor. The user may want to set the rts threshold. But since we have not been taking over rate control from mac80211 to driver by setting flag IEEE80211_HW_HAS_RATE_CONTROL, there is nothing we can do about it. So here just store the value, and mac80211 will tell us to use rts protection by ieee80211_tx_info::control::use_rts. Signed-off-by:
-
Chin-Yen Lee authored
Driver needs to wait for firmware to restore hardware setting to active mode after leaving lps. After getting H2C from driver for leaving lps, firmware will issue null packet without PS bit to inform AP driver is active, and then restore REG_TCR Register if AP has receiced null packet. But the transmission of null packet may cost much more time in noisy environment. If driver does not wait for firmware, null packet with PS bit could be sent due to incorrect REG_TCR setting. And AP will be confused. In our test, 100ms is enough for firmware to send null packet to AP. If REG_TCR Register is still wrong after 100ms, we will modify it directly, force the PS bit to be cleared Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
- 03 Oct, 2019 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for 5.5. Major changes: ath10k * add support for hardware rfkill on devices where firmware supports it
-
- 02 Oct, 2019 6 commits
-
-
Denis Efremov authored
memcpy() in wmi_set_ie() and wmi_update_ft_ies() is called with src == NULL and len == 0. This is an undefined behavior. Fix it by checking "ie_len > 0" before the memcpy() calls. As suggested by GCC documentation: "The pointers passed to memmove (and similar functions in <string.h>) must be non-null even when nbytes==0, so GCC can use that information to remove the check after the memmove call." [1] [1] https://gcc.gnu.org/gcc-4.9/porting_to.html Cc: Maya Erez <merez@codeaurora.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: stable@vger.kernel.org Signed-off-by:
-
Denis Efremov authored
memcpy() call with "idata == NULL && ilen == 0" results in undefined behavior in ar5523_cmd(). For example, NULL is passed in callchain "ar5523_stat_work() -> ar5523_cmd_write() -> ar5523_cmd()". This patch adds ilen check before memcpy() call in ar5523_cmd() to prevent an undefined behavior. Cc: Pontus Fuchs <pontus.fuchs@gmail.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: David Laight <David.Laight@ACULAB.COM> Cc: stable@vger.kernel.org Signed-off-by:
-
Wen Gong authored
When hardware rfkill is enabled in the firmware it will report the capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event to the host. ath10k will check the capability, and if it is enabled then ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When the firmware detects hardware rfkill is enabled by the user, it will report it via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio and also notifies cfg80211. We can't power off the device when rfkill is enabled, as otherwise the firmware would not be able to detect GPIO changes and report them to the host. So when rfkill is enabled, we need to keep the firmware running. Tested with QCA6174 PCI with firmware WLAN.RM.4.4.1-00109-QCARMSWPZ-1. Signed-off-by:
Alan Liu <alanliu@codeaurora.org> Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Christian Lamparter authored
This patch restores the old behavior that read the chip_id on the QCA988x before resetting the chip. This needs to be done in this order since the unsupported QCA988x AR1A chips fall off the bus when resetted. Otherwise the next MMIO Op after the reset causes a BUS ERROR and panic. Cc: stable@vger.kernel.org Fixes: 1a7fecb7 ("ath10k: reset chip before reading chip_id in probe") Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Ben Greear authored
Offchannel management frames were failing: [18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780 [18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780 [18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780 [18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780 [18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0 [18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00 [18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0 [18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00 This bug appears to have been added between 4.0 (which works for us), and 4.4, which does not work. I think this is because the tx-offchannel logic gets in a loop when ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually sent to the firmware for transmit. This patch fixes the problem on 4.9 for me, and now HS20 clients can work again with my firmware. Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888 Signed-off-by:
Ben Greear <greearb@candelatech.com> Tested-by:
Antonio Quartulli <antonio.quartulli@kaiwoo.ai> [kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis] Signed-off-by:
-
Dan Carpenter authored
The "priv->hw_type" is an enum and in this context GCC will treat it as an unsigned int so the error handling will never trigger. Fixes: a910e4a9 ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets") Signed-off-by:
-
