Adjust a jump target so that a bit of exception handling can be better
reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

* Return directly after a call of the function “kzalloc” failed
  at the beginning.

* Delete a label which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We can have the same src ids for different client ids so make sure to
check both the client id and the source id when handling interrupts.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

We need to take into account the client id otherwise we'll end
up sending generic events for any src id that is registered.

We only support irq domains on pre-soc15 parts so client is
always legacy.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

tear down software ih ring and its state.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

software ih ring is enabled in vega10 and navi
ih block by default.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

software ih ring will be used as a workaround
in case hardware ih ring 1 and ring 2 don't work
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is supported by Sienna Cichlid, Navy Flounder and Dimgrey
Cavefish. For these ASICs, the target voltage calculation can be
illustrated by "voltage = voltage calculated from v/f curve +
overdrive vddgfx offset".

V2: limit the smu_version check for Sienna Cichlid only

Here are some sample usages about this new OD setting:
1. Check current vddgfx offset setting by
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
0mV
...
...

2. Set new vddgfx offset by
echo "vo 10" > /sys/class/drm/card0/device/pp_od_clk_voltage
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
10mV
...
...
3. Commit the new setting by
echo "c" > /sys/class/drm/card0/device/pp_od_clk_voltage
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable Sienna Cichlid gfxclk/uclk overdrive support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Populate the bootup overdrive table settings.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When user specifies a reduced WGP(CU) config via disalbe_cu module
parameter, this does not disable the clocks which uses additional
power. This interface send active WGP number to SMU and SMU will
cooperate with RLC to power off relative WGPs.

v2: Add request active WGPs in Vangogh smu post init.
Signed-off-by: Jinzhou.Su <Jinzhou.Su@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Documents the hooks in struct pptable_funcs.

v2: Improved documentation accuracy.
v3: Improved set_default_od_settings() definition.
Signed-off-by: Ryan Taylor <Ryan.Taylor@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

APUs don't support ih ring 1 and ring 2.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For all the ASICs that integrate psp v11, vega20
doesn't support ih reroute. arcturus and later will
allow kernel driver to program ih_cfg_index/data
through mmio directly. navi1x and onwards will only
support grb_ih_set command in sriov configuration.

psp_v11_0_reroute_ih is not needed any more.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

except for RENOIR, it is not correct to have
IH_CHICKEN programming in vega10 ih block.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

IH_CHICKEN.MC_SPACE_FBPA_ENABLE field is only
valid when IH_RB_CNTL.MC_SPACE is programed to 0x3,
frame buffer physical address. For both bus address
and gpu virtual address, don't program MC_SPACE_FBPA_ENABLE
field
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

already switched to vega20 ih block for vega20
and arcturus. no need to add vega20 support in
navi10 ih block
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

replace navi10 ih block with vega20 ih block for
vega20 and arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

in case page faults overwhlem the interrupt handlers
and the driver lost the valuable interrupt information
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

vega20 ih blocks will be used for vega20/arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v1: add osssys v4_2 register offset and shift masks
header files. vega20 and arcturus will refer to
these ip headers. (Hawking)
v2: clean up osssys v4_2 registers (Alex)
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>

The iv format is the same for all the soc15 adpater
and onwards and can share a common function to
decode iv.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

since from soc15, all the chips share the same
iv format. create a common helper to decode iv
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

all the ih rb control register offsets are cached
at the beginning of navi10 ih_sw_init.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

use navi10_ih_enable_ring to enable all the
available ring buffers for navi1x and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

replace ih_enable_interrupts and ih_disable_interrupts
with ih_toggle_interrupts
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initialize ih control registers offset through helper
function navi10_ih_init_register_offset.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

navi10_ih_toggle_ring_interrupts will be used to
enable/disable an ih ring interrupts for navi1x
and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

navi10_ih_enable_ring will be used to enable an
ih ring for navi1x and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

navi10_ih_init_register_offset will be used to init
register offset for all the available ih rings
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

vega10/12 and RAVEN don't support soft override
ih_buffer_mem_clk.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

all the ih rb control register offsets are cached
at the beginning of ih_sw_init.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

use vega10_ih_enable_ring to enable all the
available ring buffers for vega10/12, RAVEN
series and RENOIR APUs
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

replace ih_enable_interrupts and ih_disable_interrupts
with ih_toggle_interrupts
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Initialize ih control registers offset through helper
function vega10_ih_init_register_offset.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

vega10_ih_toggle_ring_interrupts will be used to
enable/disable an ih ring interrupts for vega10/12,
RAVEN series and RENOIR APUs
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

vega10_ih_enable_ring will be used to enable an
ih ring for vega10/12, RAVEN series and RENOIR.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

vega10_ih_init_register_offset will be used to init
register offset for all the available ih rings
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amdgpu_ih_regs holds all the registers for
an ih ring
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in  memory leak.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org