This reverts commit 24b91e36 and commit
7bdb59f1 ("tick/nohz: Fix possible missing clock reprog after tick
soft restart") that depends on it,

Pavel reports that it causes occasional boot hangs for him that seem to
depend on just how the machine was booted.  In particular, his machine
hangs at around the PCI fixups of the EHCI USB host controller, but only
hangs from cold boot, not from a warm boot.

Thomas Gleixner suspecs it's a CPU hotplug interaction, particularly
since Pavel also saw suspend/resume issues that seem to be related.
We're reverting for now while trying to figure out the root cause.
Reported-bisected-and-tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org  # reverted commits were marked for stable
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull media fix from Mauro Carvalho Chehab:
 "A regression fix that makes the Siano driver to work again after the
  CONFIG_VMAP_STACK change"

* tag 'media/v4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] siano: make it work again with CONFIG_VMAP_STACK

Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer.  Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.

Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # 2.6.17+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull fuse fixes from Miklos Szeredi:
 "Fix a use after free bug introduced in 4.2 and using an uninitialized
  value introduced in 4.9"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix uninitialized flags in pipe_buffer
  fuse: fix use after free issue in fuse_dev_do_read()

Pull PCI fix from Bjorn Helgaas:
 "Add back pcie_pme_remove() so we free the IRQ when removing PCIe port
  devices; previously the leaked IRQ caused an MSI BUG_ON"

* tag 'pci-v4.10-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/PME: Restore pcie_pme_driver.remove

Pull networking fixes from David Miller:

 1) In order to avoid problems in the future, make cgroup bpf overriding
    explicit using BPF_F_ALLOW_OVERRIDE. From Alexei Staovoitov.

 2) LLC sets skb->sk without proper skb->destructor and this explodes,
    fix from Eric Dumazet.

 3) Make sure when we have an ipv4 mapped source address, the
    destination is either also an ipv4 mapped address or
    ipv6_addr_any(). Fix from Jonathan T. Leighton.

 4) Avoid packet loss in fec driver by programming the multicast filter
    more intelligently. From Rui Sousa.

 5) Handle multiple threads invoking fanout_add(), fix from Eric
    Dumazet.

 6) Since we can invoke the TCP input path in process context, without
    BH being disabled, we have to accomodate that in the locking of the
    TCP probe. Also from Eric Dumazet.

 7) Fix erroneous emission of NETEVENT_DELAY_PROBE_TIME_UPDATE when we
    aren't even updating that sysctl value. From Marcus Huewe.

 8) Fix endian bugs in ibmvnic driver, from Thomas Falcon.

[ This is the second version of the pull that reverts the nested
  rhashtable changes that looked a bit too scary for this late in the
  release  - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  rhashtable: Revert nested table changes.
  ibmvnic: Fix endian errors in error reporting output
  ibmvnic: Fix endian error when requesting device capabilities
  net: neigh: Fix netevent NETEVENT_DELAY_PROBE_TIME_UPDATE notification
  net: xilinx_emaclite: fix freezes due to unordered I/O
  net: xilinx_emaclite: fix receive buffer overflow
  bpf: kernel header files need to be copied into the tools directory
  tcp: tcp_probe: use spin_lock_bh()
  uapi: fix linux/if_pppol2tp.h userspace compilation errors
  packet: fix races in fanout_add()
  ibmvnic: Fix initial MTU settings
  net: ethernet: ti: cpsw: fix cpsw assignment in resume
  kcm: fix a null pointer dereference in kcm_sendmsg()
  net: fec: fix multicast filtering hardware setup
  ipv6: Handle IPv4-mapped src to in6addr_any dst.
  ipv6: Inhibit IPv4-mapped src address on the wire.
  net/mlx5e: Disable preemption when doing TC statistics upcall
  rhashtable: Add nested tables
  tipc: Fix tipc_sk_reinit race conditions
  gfs2: Use rhashtable walk interface in glock_hash_walk
  ...

Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: d82718e3 ("fuse_dev_splice_read(): switch to add_to_pipe()")
Cc: <stable@vger.kernel.org> # 4.9+

This reverts commits:

6a254780
9dbbfb0a
40137906

It's too risky to put in this late in the release
cycle.  We'll put these changes into the next merge
window instead.
Signed-off-by: David S. Miller <davem@davemloft.net>

Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When setting a neigh related sysctl parameter, we always send a
NETEVENT_DELAY_PROBE_TIME_UPDATE netevent. For instance, when
executing

	sysctl net.ipv6.neigh.wlp3s0.retrans_time_ms=2000

a NETEVENT_DELAY_PROBE_TIME_UPDATE netevent is generated.

This is caused by commit 2a4501ae ("neigh: Send a
notification when DELAY_PROBE_TIME changes"). According to the
commit's description, it was intended to generate such an event
when setting the "delay_first_probe_time" sysctl parameter.

In order to fix this, only generate this event when actually
setting the "delay_first_probe_time" sysctl parameter. This fix
should not have any unintended side-effects, because all but one
registered netevent callbacks check for other netevent event
types (the registered callbacks were obtained by grepping for
"register_netevent_notifier"). The only callback that uses the
NETEVENT_DELAY_PROBE_TIME_UPDATE event is
mlxsw_sp_router_netevent_event() (in
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c): in case
of this event, it only accesses the DELAY_PROBE_TIME of the
passed neigh_parms.

Fixes: 2a4501ae ("neigh: Send a notification when DELAY_PROBE_TIME changes")
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.

The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.

I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.

In commit 123c1407 ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.

Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.

Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407 ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>

xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.

Fix those cases.

Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2dd ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>

In addition to making PME non-modular, d7def204 ("PCI/PME: Make
explicitly non-modular") removed the pcie_pme_driver .remove() method,
pcie_pme_remove().

pcie_pme_remove() freed the PME IRQ that was requested in pci_pme_probe().
The fact that we don't free the IRQ after d7def204 causes the following
crash when removing a PCIe port device via /sys:

  ------------[ cut here ]------------
  kernel BUG at drivers/pci/msi.c:370!
  invalid opcode: 0000 [#1] SMP
  Modules linked in:
  CPU: 1 PID: 14509 Comm: sh Tainted: G    W  4.8.0-rc1-yh-00012-gd29438d6
  RIP: 0010:[<ffffffff9758bbf5>]  free_msi_irqs+0x65/0x190
  ...
  Call Trace:
   [<ffffffff9758cda4>] pci_disable_msi+0x34/0x40
   [<ffffffff97583817>] cleanup_service_irqs+0x27/0x30
   [<ffffffff97583e9a>] pcie_port_device_remove+0x2a/0x40
   [<ffffffff97584250>] pcie_portdrv_remove+0x40/0x50
   [<ffffffff97576d7b>] pci_device_remove+0x4b/0xc0
   [<ffffffff9785ebe6>] __device_release_driver+0xb6/0x150
   [<ffffffff9785eca5>] device_release_driver+0x25/0x40
   [<ffffffff975702e4>] pci_stop_bus_device+0x74/0xa0
   [<ffffffff975704ea>] pci_stop_and_remove_bus_device_locked+0x1a/0x30
   [<ffffffff97578810>] remove_store+0x50/0x70
   [<ffffffff9785a378>] dev_attr_store+0x18/0x30
   [<ffffffff97260b64>] sysfs_kf_write+0x44/0x60
   [<ffffffff9725feae>] kernfs_fop_write+0x10e/0x190
   [<ffffffff971e13f8>] __vfs_write+0x28/0x110
   [<ffffffff970b0fa4>] ? percpu_down_read+0x44/0x80
   [<ffffffff971e53a7>] ? __sb_start_write+0xa7/0xe0
   [<ffffffff971e53a7>] ? __sb_start_write+0xa7/0xe0
   [<ffffffff971e1f04>] vfs_write+0xc4/0x180
   [<ffffffff971e3089>] SyS_write+0x49/0xa0
   [<ffffffff97001a46>] do_syscall_64+0xa6/0x1b0
   [<ffffffff9819201e>] entry_SYSCALL64_slow_path+0x25/0x25
  ...
   RIP  [<ffffffff9758bbf5>] free_msi_irqs+0x65/0x190
   RSP <ffff89ad3085bc48>
  ---[ end trace f4505e1dac5b95d3 ]---
  Segmentation fault

Restore pcie_pme_remove().

[bhelgaas: changelog]
Fixes: d7def204 ("PCI/PME: Make explicitly non-modular")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org	# v4.9+

There is a potential race between fuse_dev_do_write()
and request_wait_answer() contexts as shown below:

TASK 1:
__fuse_request_send():
  |--spin_lock(&fiq->waitq.lock);
  |--queue_request();
  |--spin_unlock(&fiq->waitq.lock);
  |--request_wait_answer():
       |--if (test_bit(FR_SENT, &req->flags))
       <gets pre-empted after it is validated true>
                                   TASK 2:
                                   fuse_dev_do_write():
                                     |--clears bit FR_SENT,
                                     |--request_end():
                                        |--sets bit FR_FINISHED
                                        |--spin_lock(&fiq->waitq.lock);
                                        |--list_del_init(&req->intr_entry);
                                        |--spin_unlock(&fiq->waitq.lock);
                                        |--fuse_put_request();
       |--queue_interrupt();
       <request gets queued to interrupts list>
            |--wake_up_locked(&fiq->waitq);
       |--wait_event_freezable();
       <as FR_FINISHED is set, it returns and then
       the caller frees this request>

Now, the next fuse_dev_do_read(), see interrupts list is not empty
and then calls fuse_read_interrupt() which tries to access the request
which is already free'd and gets the below crash:

[11432.401266] Unable to handle kernel paging request at virtual address
6b6b6b6b6b6b6b6b
...
[11432.418518] Kernel BUG at ffffff80083720e0
[11432.456168] PC is at __list_del_entry+0x6c/0xc4
[11432.463573] LR is at fuse_dev_do_read+0x1ac/0x474
...
[11432.679999] [<ffffff80083720e0>] __list_del_entry+0x6c/0xc4
[11432.687794] [<ffffff80082c65e0>] fuse_dev_do_read+0x1ac/0x474
[11432.693180] [<ffffff80082c6b14>] fuse_dev_read+0x6c/0x78
[11432.699082] [<ffffff80081d5638>] __vfs_read+0xc0/0xe8
[11432.704459] [<ffffff80081d5efc>] vfs_read+0x90/0x108
[11432.709406] [<ffffff80081d67f0>] SyS_read+0x58/0x94

As FR_FINISHED bit is set before deleting the intr_entry with input
queue lock in request completion path, do the testing of this flag and
queueing atomically with the same lock in queue_interrupt().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: fd22d62e ("fuse: no fc->lock for iqueue parts")
Cc: <stable@vger.kernel.org> # 4.2+

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_rcv_established() can now run in process context.

We need to disable BH while acquiring tcp probe spinlock,
or risk a deadlock.

Fixes: 5413d1ba ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because of <linux/libc-compat.h> interface limitations, <netinet/in.h>
provided by libc cannot be included after <linux/in.h>, therefore any
header that includes <netinet/in.h> cannot be included after <linux/in.h>.

Change uapi/linux/l2tp.h, the last uapi header that includes
<netinet/in.h>, to include <linux/in.h> and <linux/in6.h> instead of
<netinet/in.h> and use __SOCK_SIZE__ instead of sizeof(struct sockaddr)
the same way as uapi/linux/in.h does, to fix linux/if_pppol2tp.h userspace
compilation errors like this:

In file included from /usr/include/linux/l2tp.h:12:0,
                 from /usr/include/linux/if_pppol2tp.h:21,
/usr/include/netinet/in.h:31:8: error: redefinition of 'struct in_addr'

Fixes: 47c3e778 ("net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported as a Kaffeine bug:
	https://bugs.kde.org/show_bug.cgi?id=375811

The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.

On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.

Tested with USB ID 2040:5510: Hauppauge Windham

Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Multiple threads can call fanout_add() at the same time.

We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.

Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.

Fixes: dc99f600 ("packet: Add fanout support.")
Fixes: 0648ab70 ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.

It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.

Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.

Fixes: 606f3993
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.

Fixes: 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jonathan T. Leighton says:

====================
IPv4-mapped on wire, :: dst address issue

Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.

linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g

 _bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)

per the kernel documention, preemption should be disabled, add that.

Before the fix, when running with CONFIG_PREEMPT set, we get a

BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793

asserion from the TC action (mirred) stats_update callback.

Fixes: aad7e08d ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull media fixes from Mauro Carvalho Chehab:
 "A colorspace regression fix in V4L2 core and a CEC core bug that makes
  it discard valid messages"

* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] cec: initiator should be the same as the destination for, poll
  [media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB

Herbert Xu says:

====================
rhashtable: Handle table allocation failure during insertion

v2 -

Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.

v1 -

This series tackles the problem of table allocation failures during
insertion.  The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.

The first two patches removes manual hash table walks which cannot
work on a nested table.

The final patch introduces nested tables.

I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion.  As we cannot use vmalloc, we solve it by making our
hash table nested.  That is, we allocate single pages at each level
and reach our desired table size by nesting them.

When a nested table is created, only a single page is allocated
at the top-level.  Lower levels are allocated on demand during
insertion.  Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.

After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible.  Also,
the rehash code will never rehash into a nested table.  If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two problems with the function tipc_sk_reinit.  Firstly
it's doing a manual walk over an rhashtable.  This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.

Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.

This patch fixes both problems.

Fixes: 07f6c4bc ("tipc: convert tipc reference table to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function glock_hash_walk walks the rhashtable by hand.  This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.

This patch replaces the manual walk by using the rhashtable walk
interface.

Fixes: 88ffbf3e ("GFS2: Use resizable hash table for glocks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized.  For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:

$ cat /proc/net/arp
IP address       HW type     Flags       HW address            Mask     Device
192.168.122.1    0x1         0x2         52:54:00:00:5d:5f     *        ens3
172.20.1.99      0x3         0x0              *        bpq0

The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:

$ arp
Address                  HWtype  HWaddress           Flags Mask            Iface
gateway                  ether   52:54:00:00:5d:5f   C                     ens3
172.20.1.99                      (incomplete)                              ens3

This changes the content of /proc/net/arp to:

$ cat /proc/net/arp
IP address       HW type     Flags       HW address            Mask     Device
172.20.1.99      0x3         0x0         *                     *        bpq0
192.168.122.1    0x1         0x2         52:54:00:00:5d:5f     *        ens3

To do so it change ax2asc to put the string "*" in buf for a NULL address
argument.  Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ghostprotocols.net domain is not working, remove it from CREDITS and
MAINTAINERS, and change the status to "Odd fixes", and since I haven't
been maintaining those, remove my address from there.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Poll messages that are used to allocate a logical address should
use the same initiator as the destination. Instead, it expected that
the initiator was 0xf which is not according to the standard.

This also had consequences for the message checks in cec_transmit_msg_fh
that incorrectly rejected poll messages with the same initiator and
destination.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This reverts 'commit 7e0739cd ("[media] videodev2.h: fix
sYCC/AdobeYCC default quantization range").

The problem is that many drivers can convert R'G'B' content (often
from sensors) to Y'CbCr, but they all produce limited range Y'CbCr.

To stay backwards compatible the default quantization range for
sRGB and AdobeRGB Y'CbCr encoding should be limited range, not full
range, even though the corresponding standards specify full range.

Update the V4L2_MAP_QUANTIZATION_DEFAULT define accordingly and
also update the documentation.

Fixes: 7e0739cd ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range")
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v4.9 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

It seems nobody used LLC since linux-3.12.

Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.

Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.

Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.

Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.

Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X

2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.

3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.

In the future this behavior may be extended with a chain of
non-overridable programs.

Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.

Add several testcases and adjust libbpf.

Fixes: 30070984 ("cgroup: add support for eBPF programs")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: David S. Miller <davem@davemloft.net>