Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
  full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
  in that order.
- We monitor the programmed filter count, if enough room is created due
  to filter deletion/reset, we then re-enable SB and ATR new rule addition.

Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This variable is a bit mask. It is needed to differentiate between
user enforced feature disables and auto disable of features due to
HW resource limitations.

Change-ID: Ib4b4f6ae1bb2668c12e482d2555100bc8ad713d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct misleading function comment.

Change-ID: I3f66cff5cc00250a285756b6500a58fad8eba4b5
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In a similar way to how ixgbe works, print a short one-line string
showing what features and number of queues the driver and hardware has
enabled at probe time.

Example (wrapped for the commit message):
i40e 0000:06:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 32 FDir RSS
ATR NTUPLE DCB

Change-ID: I177bf7f93d1c4c921529c92fdf66e614f6b4f755
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg.  It also cleans up
strings printed during reset.

Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This cleans up strings for consistency, q is replaced with queue.

Change-ID: Ia5f9dfae9af261f4c24485854264e02363729cf3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1) Fix a name of the error bit to correctly indicate the error.
2) Added a fd_id field in the 32 byte desc at the place(qw0) where it gets
reported in the programming error desc WB. In a normal data desc
the fd_id field is reported in qw3.

Change-ID: Ide9a24bff7273da5889c36635d629bc3b5212010
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The update filter logic was causing a kernel panic in the original code.
We need to compare the input set to decide whether or not to delete a
filter since we do not have a hash stored. This new design helps fix the issue.

Change-ID: I2462b108e58ca4833312804cda730b4660cc18c9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We've been deleting the netdev before getting around to deleting the napi
structs.  Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.

Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Recently added code comment was missing a space that is needed.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

most of these are only used locally, make them static.
fold lowpan_expire_frag_queue into its caller, its small enough.

Cc: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the sh_eth device is registered using OF, then the driver
should call of_mdiobus_register() to register the PHYs described
in the devicetree and then use of_phy_connect() to connect the
PHYs to the device.

This ensures that any PHYs registered in the device tree are
appropriately connected to the parent devices nodes so that
the PHY drivers can access their OF properties.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

nla_nest_end() already has return skb->len, so replace
return skb->len with return nla_nest_end instead().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcm_enet_netpoll does not exist, and causing
bcm63xx_net to fail to build when NET_POLL_CONTROLLER
is defined.

Remove the bogus .ndo_poll_controller = bcm_enet_netpoll
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric W. Biederman says:

====================
Don't receive packets when the napi budget == 0

To the best of understanding processing any received packets when the
napi budget == 0 is broken driver behavior.  At the same time I don't
think we have ever cared before so there are a handful of drivers that
need fixes.

I care now as I will shortly be using htis in netpoll to get the
tx queue processing without the rx queue processing.

Drivers that need fixes are few and far between, and so far I have only
found two of them.  More similar patches later if I find more drivers
that need fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

consolidate duplicate code is skb_checksum_setup() helpers

Realizing that the skb_maybe_pull_tail() calls in the IP-protocol
specific portions of both helpers are terminal ones (i.e. no further
pulls are expected), their maximum size to be pulled can be made match
their minimal size needed, thus making the code identical and hence
possible to be moved into another helper.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb, e1000e, ixgbe and ixgbevf.

Tom Herbert provides changes to e1000e, igb and ixgbe to call skb_set_hash()
to set the hash and its type in an skbuff.

Carolyn provides a fix for igb where using ethtool for EEE settings, which
was not working correctly.

Jacob provides some trivial cleanups and fixes for ixgbe which mainly
dealt with the file headers.

Julia Lawall provides a one fix for ixgbevf where the driver did not need
to adjust the power state on suspend, so the call to pci_set_power_state()
in the resume function was a no-op.

v2:
- dropped patches 4-6 from original series which implemented debugfs for
  igb from Carolyn based on feed back from David Miller and Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
For the mac80211 bits, Johannes says:

"This time, I have a number of small fixes and improvements, and those
are fairly straight-forward. More interesting changes come from Luca
with some preparations for the CSA work, mostly around interface/channel
combinations checking. One other possibly interesting change is a small
one by myself to add NAPI support back to mac80211, which can help
improve TCP behaviour through GRO."

For the Bluetooth bits, Gustavo says:

"This is our first pull request for 3.15, the main feature here is the addition of
the privacy feature for low energy devices. Other than that we have a bunch of small
improvements, fixes, and clean ups all over the tree."

And...

"Another pull request to 3.15. Here we have the second part of the LE private
feature, the LE auto-connect feature and improvements to the power off
procedures. The rest are small improvements, clean up, and fixes."

For the iwlwifi bits, Emmanuel says:

"I have here a whole bunch of various things. Trivial cleanups,
debugfs handlers and new stuff for the new generation of devices
along with new capabilities for monitor mode. We also have support
for power save for dual interface mode, but that is not supported by
the firmware currently available."

And for the Atheros bits, Kalle says:

"For ath10k Alexander did some cleanup to PCI error cases and switched
ath10k to use pci_enable_msi_range(). Michal implemented AP CSA support
and sta_rc_update() operation. I enabled firmware "STA quick kickout"
functionality for faster detection of disappeared clients.

Also there are lots of small fixes to everywhere from various people."

I pulled the wireless tree to avoid some merge conflicts, and I
reverted the staging patch that I had mistakenly merged previously.
Along with that, mwifiex, brcmfmac, wil6210, ath9k, and a few other
drivers get their usual round of updates.  Also notable is the addition
of yet another driver in the rtlwifi family.

 ...

I have amended this commit request to correct the build problems in
staging, including a warning added to one of the staging drivers by
the wireless-next tree.  I also included a fix from Larry Finger to
address an issue found in rtl8723be by Dan Carpenter and smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Misc. fixes for cxgb4

This patch series provides miscelleneous fixes for Chelsio T4/T5 adapters
cxgb4 driver related to SGE and MTU.

Also fixes regression in LSO calcuation path.
("cxgb4: Calculate len properly for LSO path")

The patches series is created against David Miller's 'net-next' tree.
And includes patches on cxgb4 driver.

We would like to request this patch series to get merged via David Miller's
'net-next' tree.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0034b298 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
introduced a regression where-in length was calculated wrongly for LSO path,
causing chip hangs.
So, correct the calculation of len.

Fixes: 0034b298 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and the
extant logic would flag that as an error.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c

Commit a619d1ab leads to the following static checker warning:

drivers/net/wireless/rtlwifi/rtl8723be/phy.c:667 _rtl8723be_store_tx_power_by_rate()
error: buffer overflow 'rtlphy->tx_power_by_rate_offset[band]' 4 <= 5

This warning arises because the code is testing the indices for the wrong maximum
values. In addition, the tests merely putput a warning, and then procedes to
corrupt memory. With this change, any such invalid memory access is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 3ebe8e25 ("ieee80211: remove function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}") removed
ieee80211_dsss_chan_to_freq, but it neglected to account for this
staging driver...

Cc: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit d8ca16db ("mac80211: add length check in
ieee80211_is_robust_mgmt_frame()") changed that API to take an skb,
and added "_ieee80211_is_robust_mgmt_frame" as a direct replacement
for the older API.  This is the same fix that was applied to the other
rtlwifi drivers in that commit.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is basically just to let Coverity et al shut up. Remove an
unneeded NULL check in sctp_assoc_update_retran_path().

It is safe to remove it, because in sctp_assoc_update_retran_path()
we iterate over the list of transports, our own transport which is
asoc->peer.retran_path included. In the iteration, we skip the
list head element and transports in state SCTP_UNCONFIRMED.

Such transports came from peer addresses received in INIT/INIT-ACK
address parameters. They are not yet confirmed by a heartbeat and
not available for data transfers.

We know however that in the list of transports, even if it contains
such elements, it at least contains our asoc->peer.retran_path as
well, so even if next to that element, we only encounter
SCTP_UNCONFIRMED transports, we are always going to fall back to
asoc->peer.retran_path through sctp_trans_elect_best(), as that is
for sure not SCTP_UNCONFIRMED as per fbdf501c ("sctp: Do no
select unconfirmed transports for retransmissions").

Whenever we call sctp_trans_elect_best() it will give us a non-NULL
element back, and therefore when we break out of the loop, we are
guaranteed to have a non-NULL transport pointer, and can remove
the NULL check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 161d7855.

Reversal of fortune -- I thought this was going to be resolved by other
means, but that hasn't materialized.  Plus, apparently we now care more
than I realized about not breaking staging drivers...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver does not need to adjust the power state on suspend, so the
call to pci_set_power_state in the resume function is a no-op.  Drop it,
to make the code more understandable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some formatting on multilined print messages, so that
the text of the print appears on a single line, which aids in grepping
the sourcecode for where the error came from.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The header above this function did not match the function prototype.
This patch rewords the comment to specify the correct parameters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the contact information on the ixgbe driver files so
that every file includes the Linux NICS address, as it is still used,
but only a few of the files mentioned it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

cppcheck detected following warning in ixgbe_fcoe.c
(warning) %d in format string (no. 1) requires 'int' but the
argument type is 'unsigned int'.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where using ethtool for EEE setting was not
working correctly.  This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: Rashika Kheria <rashika.kheria@gmail.com>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>