These convenience wrappers match the other _irq and _bh wrappers we
already have.  It turns out I'd already open-coded xa_cmpxchg_irq()
in the shmem code, so convert that.
Signed-off-by: Matthew Wilcox <willy@infradead.org>

Commit 66ee620f ("idr: Permit any valid kernel pointer to be stored")
changed the radix tree lookup so that it stops when reaching the bottom
of the tree.  However, the condition was added in the wrong place,
making it possible to return retry entries to the caller.  Reorder the
tests to check for the retry entry before checking whether we're at the
bottom of the tree.  The retry entry should never be found in the tree
root, so it's safe to defer the check until the end of the loop.

Add a regression test to the test-suite to be sure this doesn't come
back.

Fixes: 66ee620f ("idr: Permit any valid kernel pointer to be stored")
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Matthew Wilcox <willy@infradead.org>

Pull SCSI fixes from James Bottomley:
 "Four obvious bug fixes. The vmw_pscsi is so old that it's amazing
  no-one noticed before now"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: storvsc: Fix a race in sub-channel creation that can cause panic
  scsi: vmw_pscsi: Rearrange code to avoid multiple calls to free_irq during unload
  scsi: libiscsi: Fix NULL pointer dereference in iscsi_eh_session_reset
  scsi: lpfc: fix block guard enablement on SLI3 adapters

Pull ARC fixes/updates from Vineet Gupta

 - Missing reads{x}()/writes{x}() getting in the way of some drivers [Jose Abreu]

 - Builds defaulting to ARCv2 ISA based configsa [Kevin Hilman]

 - Misc fixes

* tag 'arc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: io.h: Implement reads{x}()/writes{x}()
  ARC: change defconfig defaults to ARCv2
  arc: [devboards] Add support of NFSv3 ACL
  ARC: mm: fix uninitialised signal code in do_page_fault
  ARC: [plat-hsdk] Enable DW APB GPIO support
  ARCv2: boot log unaligned access in use
  ARC: IOC: panic if kernel was started with previously enabled IOC
  ARC: remove redundant 'default n' from Kconfig

This is a full revert of ac5b2c18 ("mm: thp: relax __GFP_THISNODE for
MADV_HUGEPAGE mappings") and a partial revert of 89c83fb5 ("mm, thp:
consolidate THP gfp handling into alloc_hugepage_direct_gfpmask").

By not setting __GFP_THISNODE, applications can allocate remote hugepages
when the local node is fragmented or low on memory when either the thp
defrag setting is "always" or the vma has been madvised with
MADV_HUGEPAGE.

Remote access to hugepages often has much higher latency than local pages
of the native page size.  On Haswell, ac5b2c18 was shown to have a
13.9% access regression after this commit for binaries that remap their
text segment to be backed by transparent hugepages.

The intent of ac5b2c18 is to address an issue where a local node is
low on memory or fragmented such that a hugepage cannot be allocated.  In
every scenario where this was described as a fix, there is abundant and
unfragmented remote memory available to allocate from, even with a greater
access latency.

If remote memory is also low or fragmented, not setting __GFP_THISNODE was
also measured on Haswell to have a 40% regression in allocation latency.

Restore __GFP_THISNODE for thp allocations.

Fixes: ac5b2c18 ("mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings")
Fixes: 89c83fb5 ("mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask")
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A bit earlier in the week as usual, but there's a fix here that should
  go in sooner rather than later.

  Under a combination of circumstance, the direct issue path in blk-mq
  could corrupt data. This wasn't easy to hit, but the ones that are
  affected by it, seem to hit it pretty easily. Full explanation in the
  patch. None of the regular filesystem and storage testing has
  triggered it, even though it's been around since 4.19-rc1.

  Outside of that, whitelist trim tweak for certain Samsung devices for
  libata"

* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
  blk-mq: fix corruption with direct issue
  libata: whitelist all SAMSUNG MZ7KM* solid-state disks

Pull btrfs fix from David Sterba:
 "A patch in 4.19 introduced a sanity check that was too strict and a
  filesystem cannot be mounted.

  This happens for filesystems with more than 10 devices and has been
  reported by a few users so we need the fix to propagate to stable"

* tag 'for-4.20-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: tree-checker: Don't check max block group size as current max chunk size limit is unreliable

Pull power management fix from Rafael Wysocki:
 "Revert a problematic recent commit that attempted to fix a system-wide
  suspend issue related to the freezer"

* tag 'pm-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "exec: make de_thread() freezable"

Pull mfd bugfix from Lee Jones:
 "Replace release function in cros_ec_dev"

* tag 'mfd-fixes-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  Revert "mfd: cros_ec: Use devm_kzalloc for private data"

This reverts commit 3aa2177e.

That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.

Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.

 ------------[ cut here ]------------
 Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
 WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
 Modules linked in: btusb btrtl btintel btbcm bluetooth ...
 CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
 Hardware name: Google Kevin (DT)
 pstate: 40000005 (nZcv daif -PAN -UAO)
 pc : device_release+0x80/0x90
 lr : device_release+0x80/0x90
 sp : ffff00000c47bc70
 x29: ffff00000c47bc70 x28: ffff8000e86b0d40
 x27: 0000000000000000 x26: 0000000000000000
 x25: 0000000056000000 x24: 0000000000000015
 x23: ffff8000f0bbf860 x22: ffff000000d320a0
 x21: ffff8000ee93e100 x20: ffff8000ed931428
 x19: ffff8000ed931418 x18: 0000000000000020
 x17: 0000000000000000 x16: 0000000000000000
 x15: 0000000000000400 x14: 0000000000000143
 x13: 0000000000000000 x12: 0000000000000400
 x11: 0000000000000157 x10: 0000000000000960
 x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
 x7 : 0000000000000000 x6 : ffff8000f7d520b8
 x5 : ffff8000f7d520b8 x4 : 0000000000000000
 x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
 x1 : 37d859939c964800 x0 : 0000000000000000
 Call trace:
  device_release+0x80/0x90
  kobject_put+0x74/0xe8
  device_unregister+0x20/0x30
  ec_device_remove+0x34/0x48 [cros_ec_dev]
  platform_drv_remove+0x28/0x48
  device_release_driver_internal+0x1a8/0x240
  driver_detach+0x40/0x80
  bus_remove_driver+0x54/0xa8
  driver_unregister+0x2c/0x58
  platform_driver_unregister+0x10/0x18
  cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
  __arm64_sys_delete_module+0x16c/0x1f8
  el0_svc_common+0x84/0xd8
  el0_svc_handler+0x2c/0x80
  el0_svc+0x8/0xc
 ---[ end trace a57c4625f3c60ae8 ]---

Cc: stable@vger.kernel.org
Fixes: 3aa2177e ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If we attempt a direct issue to a SCSI device, and it returns BUSY, then
we queue the request up normally. However, the SCSI layer may have
already setup SG tables etc for this particular command. If we later
merge with this request, then the old tables are no longer valid. Once
we issue the IO, we only read/write the original part of the request,
not the new state of it.

This causes data corruption, and is most often noticed with the file
system complaining about the just read data being invalid:

[  235.934465] EXT4-fs error (device sda1): ext4_iget:4831: inode #7142: comm dpkg-query: bad extra_isize 24937 (inode size 256)

because most of it is garbage...

This doesn't happen from the normal issue path, as we will simply defer
the request to the hardware queue dispatch list if we fail. Once it's on
the dispatch list, we never merge with it.

Fix this from the direct issue path by flagging the request as
REQ_NOMERGE so we don't change the size of it before issue.

See also:
  https://bugzilla.kernel.org/show_bug.cgi?id=201685Tested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 6ce3dd6e ("blk-mq: issue directly if hw queue isn't busy in case of 'none'")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull parisc fix from Helge Deller:
 "On parisc, use -ffunction-sections compiler option when building
  32-bit kernel modules to avoid sysfs-warnings when loading such
  modules.

  This got broken with kernel v4.18"

* 'parisc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Enable -ffunction-sections for modules on 32-bit kernel

Pull input updates from Dmitry Torokhov:
 "Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: omap-keypad - fix keyboard debounce configuration
  Input: xpad - quirk all PDP Xbox One gamepads
  Input: synaptics - enable SMBus for HP 15-ay000
  Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
  Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
  Input: elan_i2c - add support for ELAN0621 touchpad
  Input: hyper-v - fix wakeup from suspend-to-idle
  Input: atkbd - clean up indentation issue
  Input: st1232 - convert to SPDX identifiers
  Input: migor_ts - convert to SPDX identifiers
  Input: dt-bindings - fix a typo in file input-reset.txt
  Input: cros_ec_keyb - fix button/switch capability reports
  Input: elan_i2c - add ELAN0620 to the ACPI table
  Input: matrix_keypad - check for errors from of_get_named_gpio()

Revert commit c2239788 "exec: make de_thread() freezable" as
requested by Ingo Molnar:

"So there's a new regression in v4.20-rc4, my desktop produces this
lockdep splat:

[ 1772.588771] WARNING: pkexec/4633 still has locks held!
[ 1772.588773] 4.20.0-rc4-custom-00213-g93a49841322b #1 Not tainted
[ 1772.588775] ------------------------------------
[ 1772.588776] 1 lock held by pkexec/4633:
[ 1772.588778]  #0: 00000000ed85fbf8 (&sig->cred_guard_mutex){+.+.}, at: prepare_bprm_creds+0x2a/0x70
[ 1772.588786] stack backtrace:
[ 1772.588789] CPU: 7 PID: 4633 Comm: pkexec Not tainted 4.20.0-rc4-custom-00213-g93a49841322b #1
[ 1772.588792] Call Trace:
[ 1772.588800]  dump_stack+0x85/0xcb
[ 1772.588803]  flush_old_exec+0x116/0x890
[ 1772.588807]  ? load_elf_phdrs+0x72/0xb0
[ 1772.588809]  load_elf_binary+0x291/0x1620
[ 1772.588815]  ? sched_clock+0x5/0x10
[ 1772.588817]  ? search_binary_handler+0x6d/0x240
[ 1772.588820]  search_binary_handler+0x80/0x240
[ 1772.588823]  load_script+0x201/0x220
[ 1772.588825]  search_binary_handler+0x80/0x240
[ 1772.588828]  __do_execve_file.isra.32+0x7d2/0xa60
[ 1772.588832]  ? strncpy_from_user+0x40/0x180
[ 1772.588835]  __x64_sys_execve+0x34/0x40
[ 1772.588838]  do_syscall_64+0x60/0x1c0

The warning gets triggered by an ancient lockdep check in the freezer:

(gdb) list *0xffffffff812ece06
0xffffffff812ece06 is in flush_old_exec (./include/linux/freezer.h:57).
52	 * DO NOT ADD ANY NEW CALLERS OF THIS FUNCTION
53	 * If try_to_freeze causes a lockdep warning it means the caller may deadlock
54	 */
55	static inline bool try_to_freeze_unsafe(void)
56	{
57		might_sleep();
58		if (likely(!freezing(current)))
59			return false;
60		return __refrigerator(false);
61	}

I reviewed the ->cred_guard_mutex code, and the mutex is held across all
of exec() - and we always did this.

But there's this recent -rc4 commit:

> Chanho Min (1):
>       exec: make de_thread() freezable

  c2239788: exec: make de_thread() freezable

I believe this commit is bogus, you cannot call try_to_freeze() from
de_thread(), because it's holding the ->cred_guard_mutex."
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

[BUG]
A completely valid btrfs will refuse to mount, with error message like:
  BTRFS critical (device sdb2): corrupt leaf: root=2 block=239681536 slot=172 \
    bg_start=12018974720 bg_len=10888413184, invalid block group size, \
    have 10888413184 expect (0, 10737418240]

This has been reported several times as the 4.19 kernel is now being
used. The filesystem refuses to mount, but is otherwise ok and booting
4.18 is a workaround.

Btrfs check returns no error, and all kernels used on this fs is later
than 2011, which should all have the 10G size limit commit.

[CAUSE]
For a 12 devices btrfs, we could allocate a chunk larger than 10G due to
stripe stripe bump up.

__btrfs_alloc_chunk()
|- max_stripe_size = 1G
|- max_chunk_size = 10G
|- data_stripe = 11
|- if (1G * 11 > 10G) {
       stripe_size = 976128930;
       stripe_size = round_up(976128930, SZ_16M) = 989855744

However the final stripe_size (989855744) * 11 = 10888413184, which is
still larger than 10G.

[FIX]
For the comprehensive check, we need to do the full check at chunk read
time, and rely on bg <-> chunk mapping to do the check.

We could just skip the length check for now.

Fixes: fce466ea ("btrfs: tree-checker: Verify block_group_item")
Cc: stable@vger.kernel.org # v4.19+
Reported-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

I noticed that the Android v3.0.8 kernel on droid4 is using different
keypad values from the mainline kernel and does not have issues with
keys occasionally being stuck until pressed again. Turns out there was
an earlier patch posted to fix this as "Input: omap-keypad: errata i689:
Correct debounce time", but it was never reposted to fix use macros
for timing calculations.

This updated version is using macros, and also fixes the use of the
input clock rate to use 32768KiHz instead of 32000KiHz. And we want to
use the known good Android kernel values of 3 and 6 instead of 2 and 6
in the earlier patch.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since we continue to find tons of new variants [0,1,2,3,4,5,6] that
need the PDP quirk, let's just quirk all devices from PDP.

[0]: https://github.com/paroj/xpad/pull/104
[1]: https://github.com/paroj/xpad/pull/105
[2]: https://github.com/paroj/xpad/pull/108
[3]: https://github.com/paroj/xpad/pull/109
[4]: https://github.com/paroj/xpad/pull/112
[5]: https://github.com/paroj/xpad/pull/115
[6]: https://github.com/paroj/xpad/pull/116

Fixes: e5c9c6a8 ("Input: xpad - add support for PDP Xbox One controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

SMBus works fine for the touchpad with id SYN3221, used in the HP 15-ay000
series,

This device has been reported in these messages in the "linux-input"
mailing list:
* https://marc.info/?l=linux-input&m=152016683003369&w=2
* https://www.spinics.net/lists/linux-input/msg52525.htmlReported-by: Nitesh Debnath <niteshkd1999@gmail.com>
Reported-by: Teika Kazura <teika@gmx.com>
Signed-off-by: Teika Kazura <teika@gmx.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add ELAN061E to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15ARR.
Signed-off-by: Noah Westervelt <nwestervelt@outlook.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Added the ability to detect the ELAN0621 touchpad found in some Lenovo
laptops.
Signed-off-by: Adam Wong <adam@adamwong.me>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull media fixes from Mauro Carvalho Chehab:

 - Revert a dt-bindings patch whose driver didn't make for 4.20

 - fix a kernel oops at vicodec driver

 - fix a frame overflow at gspca with was causing regressions on some
   cameras, making them to not work

 - use the proper type for wait_queue head

 - make media request API compatible with 32-bit userspace on 64-bit
   kernel

 - fix a regression on Kernel 4.19 at dvb-pll

 - don't use SPDX headers yet for GFDL

* tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: mediactl docs: Fix licensing message
  media: dvb-pll: don't re-validate tuner frequencies
  media: dvb-pll: fix tuner frequency ranges
  media: Revert "media: dt-bindings: Document the Rockchip VPU bindings"
  media: gspca: fix frame overflow error
  media: vicodec: fix memchr() kernel oops
  media: cedrus: add action item to the TODO
  media: media-request: Add compat ioctl
  media: Use wait_queue_head_t for media_request

Pull IDE fixes from David Miller:
 "A missing of_node_put() and a small cleanup"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide: Change to use DEFINE_SHOW_ATTRIBUTE macro
  ide: pmac: add of_node_put()

Pull sparc fixes from David Miller:

 1) Some implicit switch fallthrough fixes from Stephen Rothwell.

 2) Missing of_node_put() in various sparc drivers from Yangtao Li.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  drivers/tty: add missing of_node_put()
  drivers/sbus/char: add of_node_put()
  sbus: char: add of_node_put()
  sparc32: supress another implicit-fallthrough warning
  sparc32: suppress an implicit-fallthrough warning
  sparc: suppress the implicit-fallthrough warning
  arch/sparc: Use kzalloc_node

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place is not doing this, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use of_node_put() to release the refcount.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Olof Johansson:
 "Volume is a little higher than usual due to a set of gpio fixes for
  Davinci platforms that's been around a while, still seemed appropriate
  to not hold off until next merge window.

  Besides that it's the usual mix of minor fixes, mostly corrections of
  small stuff in device trees.

  Major stability-related one is the removal of a regulator from DT on
  Rock960, since DVFS caused undervoltage. I expect it'll be restored
  once they figure out the underlying issue"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  MAINTAINERS: Remove unused Qualcomm SoC mailing list
  ARM: davinci: dm644x: set the GPIO base to 0
  ARM: davinci: da830: set the GPIO base to 0
  ARM: davinci: dm355: set the GPIO base to 0
  ARM: davinci: dm646x: set the GPIO base to 0
  ARM: davinci: dm365: set the GPIO base to 0
  ARM: davinci: da850: set the GPIO base to 0
  gpio: davinci: restore a way to manually specify the GPIO base
  ARM: davinci: dm644x: define gpio interrupts as separate resources
  ARM: davinci: dm355: define gpio interrupts as separate resources
  ARM: davinci: dm646x: define gpio interrupts as separate resources
  ARM: davinci: dm365: define gpio interrupts as separate resources
  ARM: davinci: da8xx: define gpio interrupts as separate resources
  ARM: dts: at91: sama5d2: use the divided clock for SMC
  ARM: dts: imx51-zii-rdu1: Remove EEPROM node
  ARM: dts: rockchip: Remove @0 from the veyron memory node
  arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
  arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
  arm64: dts: sdm845-mtp: Reserve reserved gpios
  arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
  ...

Pull xen fixes from Juergen Gross:

 - A revert of a previous commit as it is no longer necessary and has
   shown to cause problems in some memory hotplug cases.

 - Some small fixes and a minor cleanup.

 - A patch for adding better diagnostic data in a very rare failure
   case.

* tag 'for-linus-4.20a-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  pvcalls-front: fixes incorrect error handling
  Revert "xen/balloon: Mark unallocated host memory as UNUSABLE"
  xen: xlate_mmu: add missing header to fix 'W=1' warning
  xen/x86: add diagnostic printout to xen_mc_flush() in case of error
  x86/xen: cleanup includes in arch/x86/xen/spinlock.c

Pull dmaengine fixes from Vinod Koul:
 "This contains two fixes to at_hdmac which fixes long standing bus
  reported recently on serial transfers causing memory leak. These fixes
  were done by Richard Genoud"

* tag 'dmaengine-fix-4.20-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: at_hdmac: fix module unloading
  dmaengine: at_hdmac: fix memory leak in at_dma_xlate()

Frank Schreiner reported, that since kernel 4.18 he faces sysfs-warnings
when loading modules on a 32-bit kernel. Here is one such example:

 sysfs: cannot create duplicate filename '/module/nfs/sections/.text'
 CPU: 0 PID: 98 Comm: modprobe Not tainted 4.18.0-2-parisc #1 Debian 4.18.10-2
 Backtrace:
  [<1017ce2c>] show_stack+0x3c/0x50
  [<107a7210>] dump_stack+0x28/0x38
  [<103f900c>] sysfs_warn_dup+0x88/0xac
  [<103f8b1c>] sysfs_add_file_mode_ns+0x164/0x1d0
  [<103f9e70>] internal_create_group+0x11c/0x304
  [<103fa0a0>] sysfs_create_group+0x48/0x60
  [<1022abe8>] load_module.constprop.35+0x1f9c/0x23b8
  [<1022b278>] sys_finit_module+0xd0/0x11c
  [<101831dc>] syscall_exit+0x0/0x14

This warning gets triggered by the fact, that due to commit 24b6c225
("parisc: Build kernel without -ffunction-sections") we now get multiple .text
sections in the kernel modules for which sysfs_create_group() can't create
multiple virtual files.

This patch works around the problem by re-enabling the -ffunction-sections
compiler option for modules, while keeping it disabled for the non-module
kernel code.
Reported-by: Frank Scheiner <frank.scheiner@web.de>
Fixes: 24b6c225 ("parisc: Build kernel without -ffunction-sections")
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Helge Deller <deller@gmx.de>

Pull STIBP fallout fixes from Thomas Gleixner:
 "The performance destruction department finally got it's act together
  and came up with a cure for the STIPB regression:

   - Provide a command line option to control the spectre v2 user space
     mitigations. Default is either seccomp or prctl (if seccomp is
     disabled in Kconfig). prctl allows mitigation opt-in, seccomp
     enables the migitation for sandboxed processes.

   - Rework the code to handle the conditional STIBP/IBPB control and
     remove the now unused ptrace_may_access_sched() optimization
     attempt

   - Disable STIBP automatically when SMT is disabled

   - Optimize the switch_to() logic to avoid MSR writes and invocations
     of __switch_to_xtra().

   - Make the asynchronous speculation TIF updates synchronous to
     prevent stale mitigation state.

  As a general cleanup this also makes retpoline directly depend on
  compiler support and removes the 'minimal retpoline' option which just
  pretended to provide some form of security while providing none"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
  x86/speculation: Provide IBPB always command line options
  x86/speculation: Add seccomp Spectre v2 user space protection mode
  x86/speculation: Enable prctl mode for spectre_v2_user
  x86/speculation: Add prctl() control for indirect branch speculation
  x86/speculation: Prepare arch_smt_update() for PRCTL mode
  x86/speculation: Prevent stale SPEC_CTRL msr content
  x86/speculation: Split out TIF update
  ptrace: Remove unused ptrace_may_access_sched() and MODE_IBRS
  x86/speculation: Prepare for conditional IBPB in switch_mm()
  x86/speculation: Avoid __switch_to_xtra() calls
  x86/process: Consolidate and simplify switch_to_xtra() code
  x86/speculation: Prepare for per task indirect branch speculation control
  x86/speculation: Add command line control for indirect branch speculation
  x86/speculation: Unify conditional spectre v2 print functions
  x86/speculataion: Mark command line parser data __initdata
  x86/speculation: Mark string arrays const correctly
  x86/speculation: Reorder the spec_v2 code
  x86/l1tf: Show actual SMT state
  x86/speculation: Rework SMT state change
  sched/smt: Expose sched_smt_present static key
  ...

Pull block layer fixes from Jens Axboe:

 - Single range elevator discard merge fix, that caused crashes (Ming)

 - Fix for a regression in O_DIRECT, where we could potentially lose the
   error value (Maximilian Heyne)

 - NVMe pull request from Christoph, with little fixes all over the map
   for NVMe.

* tag 'for-linus-20181201' of git://git.kernel.dk/linux-block:
  block: fix single range discard merge
  nvme-rdma: fix double freeing of async event data
  nvme: flush namespace scanning work just before removing namespaces
  nvme: warn when finding multi-port subsystems without multipathing enabled
  fs: fix lost error code in dio_complete
  nvme-pci: fix surprise removal
  nvme-fc: initialize nvme_req(rq)->ctrl after calling __nvme_fc_init_request()
  nvme: Free ctrl device name on init failure

Pull PCI fixes from Bjorn Helgaas:

 - Fix a link speed checking interface that broke PCIe gen3 cards in
   gen1 slots (Mikulas Patocka)

 - Fix an imx6 link training error (Trent Piepho)

 - Fix a layerscape outbound window accessor calling error (Hou
   Zhiqiang)

 - Fix a DesignWare endpoint MSI-X address calculation error (Gustavo
   Pimentel)

* tag 'pci-v4.20-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Fix incorrect value returned from pcie_get_speed_cap()
  PCI: dwc: Fix MSI-X EP framework address calculation bug
  PCI: layerscape: Fix wrong invocation of outbound window disable accessor
  PCI: imx6: Fix link training status detection in link up check

  - Fix DesignWare endpoint MSI-X address calculation bug (Gustavo
    Pimentel)

  - Fix Layerscape outbound window disable usage (Hou Zhiqiang)

  - Fix imx6 link up detection (Trent Piepho)

* lorenzo/pci/controller-fixes:
  PCI: dwc: Fix MSI-X EP framework address calculation bug
  PCI: layerscape: Fix wrong invocation of outbound window disable accessor
  PCI: imx6: Fix link training status detection in link up check

The macros PCI_EXP_LNKCAP_SLS_*GB are values, not bit masks.  We must mask
the register and compare it against them.

This fixes errors like this:

  amdgpu: [powerplay] failed to send message 261 ret is 0

when a PCIe-v3 card is plugged into a PCIe-v1 slot, because the slot is
being incorrectly reported as PCIe-v3 capable.

6cf57be0, which appeared in v4.17, added pcie_get_speed_cap() with the
incorrect test of PCI_EXP_LNKCAP_SLS as a bitmask.  5d9a6330, which
appeared in v4.19, changed amdgpu to use pcie_get_speed_cap(), so the
amdgpu bug reports below are regressions in v4.19.

Fixes: 6cf57be0 ("PCI: Add pcie_get_speed_cap() to find max supported link speed")
Fixes: 5d9a6330 ("drm/amdgpu: use pcie functions for link width and speed")
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108704
Link: https://bugs.freedesktop.org/show_bug.cgi?id=108778Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[bhelgaas: update comment, remove use of PCI_EXP_LNKCAP_SLS_8_0GB and
PCI_EXP_LNKCAP_SLS_16_0GB since those should be covered by PCI_EXP_LNKCAP2,
remove test of PCI_EXP_LNKCAP for zero, since that register is required]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org	# v4.17+