The only caller of speedstep_get_state() was removed in commit d4019f0a
("cpufreq: move freq change notifications to cpufreq core"). So building
speedstep-smi.o now triggers a GCC warning:
    drivers/cpufreq/speedstep-smi.c:148:12: warning: 'speedstep_get_state' defined but not used [-Wunused-function]

Remove this unused function.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

KVM environments do not support APERF/MPERF MSRs. intel_pstate cannot
operate without these registers.

The previous validity checks in intel_pstate_msrs_not_valid() are
insufficent in nested KVMs.

References: https://bugzilla.redhat.com/show_bug.cgi?id=1046317Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:

* If there was a frequency transition before, the multiplier read from the
  register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
  register always reads as zero, regardless of the current multiplier that
  is set using switches on the mainboard and that the CPU is running at.

The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.

For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.

There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.

During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.

This patch flushes the cache during frequency transition. It fixes the
instability.

Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
  powernow_k6_set_cpu_multiplier
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
  field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
  open during other activity (running other kernel code with the port open
  shouldn't cause any misbehavior, but we should better be safe and keep
  the port closed)

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a Documentation/ABI entry for
/sys/devices/system/cpu/intel_pstate/max_perf_pct,
/sys/devices/system/cpu/intel_pstate/min_perf_pct, and
/sys/devices/system/cpu/intel_pstate/no_turbo.

Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

To make the driver multiplatform-friendly, unconditional initialization
in an initcall is replaced with a platform driver probed only if
respective platform device is registered.

Tested at: Exynos4210 (TRATS) and Exynos4412 (TRATS2)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.

Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).

In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.

On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.

Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.

Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a routine check to see if the platform supplied the OPP table.
Incase there's no OPP table exist, it will try to initialise it.

It's been tested on iMX6SL board where the platform doesn't have
an OPP table.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The imx6q-cpufreq driver nowadays is not only running on imx6q but also
other i.MX6 series SoCs like imx6dl and imx6sl.  Update Kconfig prompt
and help text to make it clear to users.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

on i.MX6Q, cpu freq change need to follow below flows:

1. each setpoint has different VDDARM, VDDSOC/PU voltage, get the setpoint
   table from dts;
2. when cpu freq is scaling up, need to increase VDDSOC/PU voltage before
   VDDARM, if VDDPU is off, no need to change it;
3. when cpu freq is scaling down, need to decrease VDDARM voltage before
   VDDSOC/PU, if VDDPU is off, no need to change it;

normally dts will pass vddsoc/pu freq/volt info to kernel, if not, will
use fixed value for vddsoc/pu voltage setting.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In the current code, if we fail during a frequency transition, we
simply send the POSTCHANGE notification with the old frequency. This
isn't enough.

One of the core users of these notifications is the code responsible
for keeping loops_per_jiffy aligned with frequency changes. And mostly
it is written as:

	if ((val == CPUFREQ_PRECHANGE  && freq->old < freq->new) ||
	    (val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
		update-loops-per-jiffy...
	}

So, suppose we are changing to a higher frequency and failed during
transition, then following will happen:
- CPUFREQ_PRECHANGE notification with freq-new > freq-old
- CPUFREQ_POSTCHANGE notification with freq-new == freq-old

The first one will update loops_per_jiffy and second one will do
nothing. Even if we send the 2nd notification by exchanging values of
freq-new and old, some users of these notifications might get
unstable.

This can be fixed by simply calling cpufreq_notify_post_transition()
with error code and this routine will take care of sending
notifications in the correct order.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Folded 3 patches into one, rebased unicore2 changes]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Use common clock framework (CCF) APIs to set the clock rates
instead of direct register manipulation. This now updates the
sysfs entry (cpuinfo_cur_freq) correctly which did not reflect
the correct value until now. While at it clean up the PLL s-div
parameter setting as it is handled by the PLL driver.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When a CPU is hot removed we'll cancel all the delayed work items via
gov_cancel_work(). Sometimes the delayed work function determines that
it should adjust the delay for all other CPUs that the policy is
managing. If this scenario occurs, the canceling CPU will cancel its own
work but queue up the other CPUs works to run.

Commit 3617f2 (cpufreq: Fix timer/workqueue corruption due to double
queueing) has tried to fix this, but reading governor_enabled is not
protected by cpufreq_governor_lock. Even though od_dbs_timer() checks
governor_enabled before gov_queue_work(), this scenario may occur. For
example:

 CPU0                                        CPU1
 ----                                        ----
 cpu_down()
  ...                                        <work runs>
  __cpufreq_remove_dev()                     od_dbs_timer()
   __cpufreq_governor()                       policy->governor_enabled
    policy->governor_enabled = false;
    cpufreq_governor_dbs()
     case CPUFREQ_GOV_STOP:
      gov_cancel_work(dbs_data, policy);
       cpu0 work is canceled
        timer is canceled
        cpu1 work is canceled
        <waits for cpu1>
                                              gov_queue_work(*, *, true);
                                               cpu0 work queued
                                               cpu1 work queued
                                               cpu2 work queued
                                               ...
        cpu1 work is canceled
        cpu2 work is canceled
        ...

At the end of the GOV_STOP case cpu0 still has a work queued to
run although the code is expecting all of the works to be
canceled. __cpufreq_remove_dev() will then proceed to
re-initialize all the other CPUs works except for the CPU that is
going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs()
will trample over the queued work and debugobjects will spit out
a warning:

WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc()
ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x14
Modules linked in:
CPU: 1 PID: 1205 Comm: sh Tainted: G        W    3.10.0 #200
[<c01144f0>] (unwind_backtrace+0x0/0xf8) from [<c0111d98>] (show_stack+0x10/0x14)
[<c0111d98>] (show_stack+0x10/0x14) from [<c01272cc>] (warn_slowpath_common+0x4c/0x68)
[<c01272cc>] (warn_slowpath_common+0x4c/0x68) from [<c012737c>] (warn_slowpath_fmt+0x30/0x40)
[<c012737c>] (warn_slowpath_fmt+0x30/0x40) from [<c034c640>] (debug_print_object+0x94/0xbc)
[<c034c640>] (debug_print_object+0x94/0xbc) from [<c034c7f8>] (__debug_object_init+0xc8/0x3c0)
[<c034c7f8>] (__debug_object_init+0xc8/0x3c0) from [<c01360e0>] (init_timer_key+0x20/0x104)
[<c01360e0>] (init_timer_key+0x20/0x104) from [<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c)
[<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c) from [<c04833a8>] (__cpufreq_governor+0x80/0x1b0)
[<c04833a8>] (__cpufreq_governor+0x80/0x1b0) from [<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380)
[<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380) from [<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c)
[<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c) from [<c014fb40>] (notifier_call_chain+0x44/0x84)
[<c014fb40>] (notifier_call_chain+0x44/0x84) from [<c012ae44>] (__cpu_notify+0x2c/0x48)
[<c012ae44>] (__cpu_notify+0x2c/0x48) from [<c068dd40>] (_cpu_down+0x80/0x258)
[<c068dd40>] (_cpu_down+0x80/0x258) from [<c068df40>] (cpu_down+0x28/0x3c)
[<c068df40>] (cpu_down+0x28/0x3c) from [<c068e4c0>] (store_online+0x30/0x74)
[<c068e4c0>] (store_online+0x30/0x74) from [<c03a7308>] (dev_attr_store+0x18/0x24)
[<c03a7308>] (dev_attr_store+0x18/0x24) from [<c0256fe0>] (sysfs_write_file+0x100/0x180)
[<c0256fe0>] (sysfs_write_file+0x100/0x180) from [<c01fec9c>] (vfs_write+0xbc/0x184)
[<c01fec9c>] (vfs_write+0xbc/0x184) from [<c01ff034>] (SyS_write+0x40/0x68)
[<c01ff034>] (SyS_write+0x40/0x68) from [<c010e200>] (ret_fast_syscall+0x0/0x48)

In gov_queue_work(), lock cpufreq_governor_lock before gov_queue_work,
and unlock it after __gov_queue_work(). In this way, governor_enabled
is guaranteed not changed in gov_queue_work().
Signed-off-by: Jane Li <jiel@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Local variable used only in this file is made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The arm_big_little cpufreq driver is only used by ARM bigLITTLE
platforms and hence must depend on CONFIG_BIG_LITTLE.

This was highlighted by Russell earlier when he reported this issue:

drivers/built-in.o: In function `bL_cpufreq_set_rate':
powercap_sys.c:(.text+0x5ed9a0): undefined reference to `bL_switch_request_cb'
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The Intel P-state driver is currently undocumented. Add some
documentation based on the cover-letter sent with the original series.

Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull battery fixes from Anton Vorontsov:
 "Two fixes:

   - fix build error caused by max17042_battery conversion to the regmap
     API.

   - fix kernel oops when booting with wakeup_source_activate enabled"

* tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6:
  max17042_battery: Fix build errors caused by missing REGMAP_I2C config
  power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate

Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
 "These commits, except for one, are regression fixes and the remaining
  one fixes a divide error leading to a kernel panic.  The majority of
  the regressions fixed here were introduced during the 3.12 cycle, one
  of them is from this cycle and one is older.

  Specifics:

   - VGA switcheroo was broken for some users as a result of the
     ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
     previously ignored hotplug events started to be handled.  The fix
     causes them to be ignored again.

   - There are two more issues related to cpufreq's suspend/resume
     handling changes from the 3.12 cycle addressed by Viresh Kumar's
     fixes.

   - intel_pstate triggers a divide error in a timer function if the
     P-state information it needs is missing during initialization.
     This leads to kernel panics on nested KVM clients and is fixed by
     failing the initialization cleanly in those cases.

   - PCI initalization code changes during the 3.9 cycle uncovered BIOS
     issues related to ACPI wakeup notifications (some BIOSes send them
     for devices that aren't supposed to support ACPI wakeup).  Work
     around them by installing an ACPI wakeup notify handler for all PCI
     devices with ACPI support.

   - The Calxeda cpuilde driver's probe function is tagged as __init,
     which is incorrect and causes a section mismatch to occur during
     build.  Fix from Andre Przywara removes the __init tag from there.

   - During the 3.12 cycle ACPIPHP started to print warnings about
     missing _ADR for devices that legitimately don't have it.  Fix from
     Toshi Kani makes it only print the warnings where they make sense"

* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
  intel_pstate: Fail initialization if P-state information is missing
  ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
  PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
  cpufreq: preserve user_policy across suspend/resume
  cpufreq: Clean up after a failing light-weight initialization
  ACPI / PCI / hotplug: Avoid warning when _ADR not present

Pull kvm bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
  KVM: x86: Fix APIC map calculation after re-enabling

Merge patches from Andrew Morton:
 "Ten fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
  sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
  drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
  mm/memory-failure.c: transfer page count from head page to tail page after split thp
  MAINTAINERS: set up proper record for Xilinx Zynq
  mm: remove bogus warning in copy_huge_pmd()
  memcg: fix memcg_size() calculation
  mm: fix use-after-free in sys_remap_file_pages
  mm: munlock: fix deadlock in __munlock_pagevec()
  mm: munlock: fix a bug where THP tail page is encountered

The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x).  The deadlock was introduced with
commmit 67347fe4 ("epoll: do not take global 'epmutex' for simple
topologies").

The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')

However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.

The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon.  The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock.  Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Nathan Zimmer <nzimmer@sgi.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Nelson Elhage <nelhage@nelhage.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Min_low_pfn and max_low_pfn were used in pfn_valid macro if defined
CONFIG_FLATMEM.  When the functions that use the pfn_valid is used in
driver module, max_low_pfn and min_low_pfn is to undefined, and fail to
build.

  ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  ERROR: "max_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
  make[2]: *** [__modpost] Error 1
  make[1]: *** [modules] Error 2

This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Check DMA mapping return values in function ioat_dma_self_test() to get
rid of following warning message.

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1203 at lib/dma-debug.c:937 check_unmap+0x4c0/0x9a0()
  ioatdma 0000:00:04.0: DMA-API: device driver failed to check map error[device address=0x000000085191b000] [size=2000 bytes] [mapped as single]
  Modules linked in: ioatdma(+) mac_hid wmi acpi_pad lp parport hidd_generic usbhid hid ixgbe isci dca libsas ahci ptp libahci scsi_transport_sas meegaraid_sas pps_core mdio
  CPU: 0 PID: 1203 Comm: systemd-udevd Not tainted 3.13.0-rc4+ #8
  Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIIN1.86B.0044.L09.1311181644 11/18/2013
  Call Trace:
    dump_stack+0x4d/0x66
    warn_slowpath_common+0x7d/0xa0
    warn_slowpath_fmt+0x4c/0x50
    check_unmap+0x4c0/0x9a0
    debug_dma_unmap_page+0x81/0x90
    ioat_dma_self_test+0x3d2/0x680 [ioatdma]
    ioat3_dma_self_test+0x12/0x30 [ioatdma]
    ioat_probe+0xf4/0x110 [ioatdma]
    ioat3_dma_probe+0x268/0x410 [ioatdma]
    ioat_pci_probe+0x122/0x1b0 [ioatdma]
    local_pci_probe+0x45/0xa0
    pci_device_probe+0xd9/0x130
    driver_probe_device+0x171/0x490
    __driver_attach+0x93/0xa0
    bus_for_each_dev+0x6b/0xb0
    driver_attach+0x1e/0x20
    bus_add_driver+0x1f8/0x2b0
    driver_register+0x81/0x110
    __pci_register_driver+0x60/0x70
    ioat_init_module+0x89/0x1000 [ioatdma]
    do_one_initcall+0xe2/0x250
    load_module+0x2313/0x2a00
    SyS_init_module+0xd9/0x130
    system_call_fastpath+0x1a/0x1f
  ---[ end trace 990c591681d27c31 ]---
  Mapped at:
    debug_dma_map_page+0xbe/0x180
    ioat_dma_self_test+0x1ab/0x680 [ioatdma]
    ioat3_dma_self_test+0x12/0x30 [ioatdma]
    ioat_probe+0xf4/0x110 [ioatdma]
    ioat3_dma_probe+0x268/0x410 [ioatdma]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Memory failures on thp tail pages cause kernel panic like below:

   mce: [Hardware Error]: Machine check events logged
   MCE exception done on CPU 7
   BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
   IP: [<ffffffff811b7cd1>] dequeue_hwpoisoned_huge_page+0x131/0x1e0
   PGD bae42067 PUD ba47d067 PMD 0
   Oops: 0000 [#1] SMP
  ...
   CPU: 7 PID: 128 Comm: kworker/7:2 Tainted: G   M       O 3.13.0-rc4-131217-1558-00003-g83b7df08e462 #25
  ...
   Call Trace:
     me_huge_page+0x3e/0x50
     memory_failure+0x4bb/0xc20
     mce_process_work+0x3e/0x70
     process_one_work+0x171/0x420
     worker_thread+0x11b/0x3a0
     ? manage_workers.isra.25+0x2b0/0x2b0
     kthread+0xe4/0x100
     ? kthread_create_on_node+0x190/0x190
     ret_from_fork+0x7c/0xb0
     ? kthread_create_on_node+0x190/0x190
  ...
   RIP   dequeue_hwpoisoned_huge_page+0x131/0x1e0
   CR2: 0000000000000058

The reasoning of this problem is shown below:
 - when we have a memory error on a thp tail page, the memory error
   handler grabs a refcount of the head page to keep the thp under us.
 - Before unmapping the error page from processes, we split the thp,
   where page refcounts of both of head/tail pages don't change.
 - Then we call try_to_unmap() over the error page (which was a tail
   page before). We didn't pin the error page to handle the memory error,
   this error page is freed and removed from LRU list.
 - We never have the error page on LRU list, so the first page state
   check returns "unknown page," then we move to the second check
   with the saved page flag.
 - The saved page flag have PG_tail set, so the second page state check
   returns "hugepage."
 - We call me_huge_page() for freed error page, then we hit the above panic.

The root cause is that we didn't move refcount from the head page to the
tail page after split thp.  So this patch suggests to do this.

This panic was introduced by commit 524fca1e ("HWPOISON: fix
misjudgement of page_action() for errors on mlocked pages").  Note that we
did have the same refcount problem before this commit, but it was just
ignored because we had only first page state check which returned "unknown
page." The commit changed the refcount problem from "doesn't work" to
"kernel panic."
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>	[3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Setup correct zynq entry.
 - Add missing cadence_ttc_timer maintainership
 - Add zynq wildcard
 - Add xilinx wildcard
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sasha Levin reported the following warning being triggered

  WARNING: CPU: 28 PID: 35287 at mm/huge_memory.c:887 copy_huge_pmd+0x145/ 0x3a0()
  Call Trace:
    copy_huge_pmd+0x145/0x3a0
    copy_page_range+0x3f2/0x560
    dup_mmap+0x2c9/0x3d0
    dup_mm+0xad/0x150
    copy_process+0xa68/0x12e0
    do_fork+0x96/0x270
    SyS_clone+0x16/0x20
    stub_clone+0x69/0x90

This warning was introduced by "mm: numa: Avoid unnecessary disruption
of NUMA hinting during migration" for paranoia reasons but the warning
is bogus.  I was thinking of parallel races between NUMA hinting faults
and forks but this warning would also be triggered by a parallel reclaim
splitting a THP during a fork.  Remote the bogus warning.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The mem_cgroup structure contains nr_node_ids pointers to
mem_cgroup_per_node objects, not the objects themselves.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

remap_file_pages calls mmap_region, which may merge the VMA with other
existing VMAs, and free "vma".  This can lead to a use-after-free bug.
Avoid the bug by remembering vm_flags before calling mmap_region, and
not trying to dereference vma later.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 7225522b ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec" introduced __munlock_pagevec() to speed
up munlock by holding lru_lock over multiple isolated pages.  Pages that
fail to be isolated are put_page()d immediately, also within the lock.

This can lead to deadlock when __munlock_pagevec() becomes the holder of
the last page pin and put_page() leads to __page_cache_release() which
also locks lru_lock.  The deadlock has been observed by Sasha Levin
using trinity.

This patch avoids the deadlock by deferring put_page() operations until
lru_lock is released.  Another pagevec (which is also used by later
phases of the function is reused to gather the pages for put_page()
operation.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit ff6a6da6 ("mm: accelerate munlock() treatment of THP
pages") munlock skips tail pages of a munlocked THP page.  However, when
the head page already has PageMlocked unset, it will not skip the tail
pages.

Commit 7225522b ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec") has added a PageTransHuge() check which
contains VM_BUG_ON(PageTail(page)).  Sasha Levin found this triggered
using trinity, on the first tail page of a THP page without PageMlocked
flag.

This patch fixes the issue by skipping tail pages also in the case when
PageMlocked flag is unset.  There is still a possibility of race with
THP page split between clearing PageMlocked and determining how many
pages to skip.  The race might result in former tail pages not being
skipped, which is however no longer a bug, as during the skip the
PageTail flags are cleared.

However this race also affects correctness of NR_MLOCK accounting, which
is to be fixed in a separate patch.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull GFS2 fixes from Steven Whitehouse:
 "Here is a set of small fixes for GFS2.  There is a fix to drop
  s_umount which is copied in from the core vfs, two patches relate to a
  hard to hit "use after free" and memory leak.  Two patches related to
  using DIO and buffered I/O on the same file to ensure correct
  operation in relation to glock state changes.  The final patch adds an
  RCU read lock to ensure correct locking on an error path"

* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Fix unsafe dereference in dump_holder()
  GFS2: Wait for async DIO in glock state changes
  GFS2: Fix incorrect invalidation for DIO/buffered I/O
  GFS2: Fix slab memory leak in gfs2_bufdata
  GFS2: Fix use-after-free race when calling gfs2_remove_from_ail
  GFS2: don't hold s_umount over blkdev_put

Pull s390 fixes from Martin Schwidefsky:
 "Two small bug fixes and a follow-up to the CONFIG_NR_CPUS change.

  A kernel compiled with CONFIG_NR_CPUS=256 will waste quite a bit of
  memory for the per-cpu arrays.  Under z/VM the maximum number of CPUs
  is 64, the code now limits the possible cpu mask to 64 if running
  under z/VM"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pci: obtain function handle in hotplug notifier
  s390/3270: fix allocation of tty3270_screen structure
  s390/smp: improve setup of possible cpu mask