While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!
ERROR: "dma_common_mmap" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!

To satisfy the dependency CONFIG_SND_SOC_LPASS_PLATFORM should depend
on HAS_DMA.
Some other configs also needs the dependency on HAS_DMA as they are
directly or indirectly selecting SND_SOC_LPASS_PLATFORM.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds wrdma support in lpass-apq8016 by providing the register
offsets and adding support in dma channel allocation callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch add mic support on apq8016-sbc board aka db410c. Tested it
with headset mic.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds mic support to the lpass driver, most of the driver is
reused as it is, only the register level access is changed depending on
te direction of the stream.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now that we are ready to access wrdma registers, set the max register
and other regmap related configs to use correct values.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds generic masks for accessing bits in rdma/wrdma
registers. Doing this would simplify the driver and adding capture
support would be much simpler. Also there is no point in having same
bit masks for bits in both rdma and wrdma registers.

This patch also deletes the RDMA specific bit masks and makes the code
use the generic bit masks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds wrdma registers into the lpaif-reg.h.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds mic related bitmasks and offsets in the i2c control
register.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds wrdma related register offsets to the lpass variant data
of ipq806x.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

rdma_ch_bit_map can be reused for wrdma channel allocations as wrdma
channel numbering start after rdma channel numbers.
With capture support referring rdma_ch_bit_map for wrdma channel allocation
is confusing, so renaming rdma_ch_bit_map to dma_ch_bit_map makes sense.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

ipq806x is only ever tested for playback so return error in dma allocation
if the stream direction is capture.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch updates the internal dma allocation callbacks to take the
stream direction so that it can allocate channels suitable for that
stream direction. Before the capture support this was not necessary.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch renames rdmactl_audif_start to dmactrl_audif_start as this
is common for both rdma and wrdma. Without this patch the name would be
bit misleading to the readers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds wrdma related register offsets, wrdma channel start
and shifts into lpass variant structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is no point in having local allocation functions when the driver
can use snd_dma_alloc/free() apis. This patch replaces the local versions
of the dma allocation apis with the snd_dma_alloc/free() apis.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

ASoC: Fixes for v4.5

A rather large batch of fixes here, almost all in the Intel driver.
The changes that got merged in this merge window for Skylake were rather
large and as well as issues that you'd expect in a large block of new
code there were some problems created for older processors which needed
fixing up.  Things are largely settling down now hopefully.

This reverts commit 18560a4e (ASoC: qcom: Specify LE device
endianness).

The commit that caused us to specify LE device endianness here,
29bb45f2 (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge remote-tracking branches 'asoc/fix/rt5659', 'asoc/fix/sigmadsp', 'asoc/fix/simple', 'asoc/fix/wm5110' and 'asoc/fix/wm8960' into asoc-linus

Merge remote-tracking branches 'asoc/fix/imx-spdif', 'asoc/fix/mtk', 'asoc/fix/mxs-saif', 'asoc/fix/qcom' and 'asoc/fix/rt286' into asoc-linus

Merge remote-tracking branches 'asoc/fix/amd', 'asoc/fix/arizona', 'asoc/fix/dpcm', 'asoc/fix/dwc', 'asoc/fix/fsl' and 'asoc/fix/fsl-ssi' into asoc-linus

When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.

This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Forwarding the return value of i2c_master_send, leads to errors
later on, since i2c_master_send returns the number of bytes
transmittet. Check for ret < 0 instead and return 0 otherwise.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

The match module lacked module license and description, so add it
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

DPCM driver is recommended for BYT, CHT based platforms, so if
CONFIG_SND_SST_IPC_ACPI is selected then don't compile the BYT
Device IDs in common ACPI driver to avoid probe conflicts.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The ACPI match module is common to all three drivers, HSW, SKL
and Atom-DPCM driver. But Atom-DPCM driver does not use common
sst code so we cannot include the common SST module in Atom-DPCM
driver.

So the solution is to have a independent sst-match-acpi module
which helps in matching for all the three drivers. Now all driver
can be inbuilt in a single image

This patch really fixes the regression introduced by the
commit 95f09801 ("ASoC: Intel: Move apci find machine routines")
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This reverts commit dc901a35 ("ASoC: Intel: fix ACPI probe
regression with Atom DPCM driver") as the fix prevented the probe
on HSW/BDW if Atom-DPCM was selected
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "The first real batch of fixes for this release cycle, so there are a
  few more than usual.

  Most of these are fixes and tweaks to board support (DT bugfixes,
  etc).  I've also picked up a couple of small cleanups that seemed
  innocent enough that there was little reason to wait (const/
  __initconst and Kconfig deps).

  Quite a bit of the changes on OMAP were due to fixes to no longer
  write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
  there were also other fixes.

  Kirkwood had a bunch of gpio fixes for some boards.  OMAP had RTC
  fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.

  All in all, mostly the usual mix of various fixes"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
  ARM: multi_v7_defconfig: enable DW_WATCHDOG
  ARM: nomadik: fix up SD/MMC DT settings
  ARM64: tegra: Add chosen node for tegra132 norrin
  ARM: realview: use "depends on" instead of "if" after prompt
  ARM: tango: use "depends on" instead of "if" after prompt
  ARM: tango: use const and __initconst for smp_operations
  ARM: realview: use const and __initconst for smp_operations
  bus: uniphier-system-bus: revive tristate prompt
  arm64: dts: Add missing DMA Abort interrupt to Juno
  bus: vexpress-config: Add missing of_node_put
  ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
  ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
  ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
  ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
  ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
  ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
  ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
  ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
  ARM: dts: am4372: fix irq type for arm twd and global timer
  ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
  ...

Pull mailbox fixes from Jassi Brar:

 - fix getting element from the pcc-channels array by simply indexing
   into it

 - prevent building mailbox-test driver for archs that don't have IOMEM

* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: Fix dependencies for !HAS_IOMEM archs
  mailbox: pcc: fix channel calculation in get_pcc_channel()

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 4.5-rc3.

  The usual, xhci fixes for reported issues, combined with some small
  gadget driver fixes, and a MAINTAINERS file update.  All have been in
  linux-next with no reported issues"

* tag 'usb-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: harden xhci_find_next_ext_cap against device removal
  xhci: Fix list corruption in urb dequeue at host removal
  usb: host: xhci-plat: fix NULL pointer in probe for device tree case
  usb: xhci-mtk: fix AHB bus hang up caused by roothubs polling
  usb: xhci-mtk: fix bpkts value of LS/HS periodic eps not behind TT
  usb: xhci: apply XHCI_PME_STUCK_QUIRK to Intel Broxton-M platforms
  usb: xhci: set SSIC port unused only if xhci_suspend succeeds
  usb: xhci: add a quirk bit for ssic port unused
  usb: xhci: handle both SSIC ports in PME stuck quirk
  usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.
  Revert "xhci: don't finish a TD if we get a short-transfer event mid TD"
  MAINTAINERS: fix my email address
  usb: dwc2: Fix probe problem on bcm2835
  Revert "usb: dwc2: Move reset into dwc2_get_hwparams()"
  usb: musb: ux500: Fix NULL pointer dereference at system PM
  usb: phy: mxs: declare variable with initialized value
  usb: phy: msm: fix error handling in probe.

Pull staging and IIO driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.5-rc3.

  All of them, except one, are for IIO drivers, and one is for a speakup
  driver fix caused by some earlier patches, to resolve a reported build
  failure"

* tag 'staging-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Staging: speakup: Fix allyesconfig build on mn10300
  iio: dht11: Use boottime
  iio: ade7753: avoid uninitialized data
  iio: pressure: mpl115: fix temperature offset sign
  iio: imu: Fix dependencies for !HAS_IOMEM archs
  staging: iio: Fix dependencies for !HAS_IOMEM archs
  iio: adc: Fix dependencies for !HAS_IOMEM archs
  iio: inkern: fix a NULL dereference on error
  iio:adc:ti_am335x_adc Fix buffered mode by identifying as software buffer.
  iio: light: acpi-als: Report data as processed
  iio: dac: mcp4725: set iio name property in sysfs
  iio: add HAS_IOMEM dependency to VF610_ADC
  iio: add IIO_TRIGGER dependency to STK8BA50
  iio: proximity: lidar: correct return value
  iio-light: Use a signed return type for ltr501_match_samp_freq()

Merge fixes from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
  radix-tree: fix oops after radix_tree_iter_retry
  MAINTAINERS: trim the file triggers for ABI/API
  dax: dirty inode only if required
  thp: make deferred_split_scan() work again
  mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
  ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
  um: asm/page.h: remove the pte_high member from struct pte_t
  mm, hugetlb: don't require CMA for runtime gigantic pages
  mm/hugetlb: fix gigantic page initialization/allocation
  mm: downgrade VM_BUG in isolate_lru_page() to warning
  mempolicy: do not try to queue pages from !vma_migratable()
  mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
  vmstat: make vmstat_update deferrable
  mm, vmstat: make quiet_vmstat lighter
  mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
  memblock: don't mark memblock_phys_mem_size() as __init
  dump_stack: avoid potential deadlocks
  mm: validate_mm browse_rb SMP race condition
  m32r: fix build failure due to SMP and MMU
  ...

Pull Ceph fixes from Sage Weil:
 "We have a few wire protocol compatibility fixes, ports of a few recent
  CRUSH mapping changes, and a couple error path fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: MOSDOpReply v7 encoding
  libceph: advertise support for TUNABLES5
  crush: decode and initialize chooseleaf_stable
  crush: add chooseleaf_stable tunable
  crush: ensure take bucket value is valid
  crush: ensure bucket id is valid before indexing buckets array
  ceph: fix snap context leak in error path
  ceph: checking for IS_ERR instead of NULL

Pull drm fixes from Dave Airlie:
 "Fixes all over the place:

   - amdkfd: two static checker fixes
   - mst: a bunch of static checker and spec/hw interaction fixes
   - amdgpu: fix Iceland hw properly, and some fiji bugs, along with
     some write-combining fixes.
   - exynos: some regression fixes
   - adv7511: fix some EDID reading issues"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (38 commits)
  drm/dp/mst: deallocate payload on port destruction
  drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
  drm/dp/mst: move GUID storage from mgr, port to only mst branch
  drm/dp/mst: change MST detection scheme
  drm/dp/mst: Calculate MST PBN with 31.32 fixed point
  drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
  drm/mst: Add range check for max_payloads during init
  drm/mst: Don't ignore the MST PBN self-test result
  drm: fix missing reference counting decrease
  drm/amdgpu: disable uvd and vce clockgating on Fiji
  drm/amdgpu: remove exp hardware support from iceland
  drm/amdgpu: load MEC ucode manually on iceland
  drm/amdgpu: don't load MEC2 on topaz
  drm/amdgpu: drop topaz support from gmc8 module
  drm/amdgpu: pull topaz gmc bits into gmc_v7
  drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
  drm/amdgpu: iceland use CI based MC IP
  drm/amdgpu: move gmc7 support out of CIK dependency
  drm/amdgpu/gfx7: enable cp inst/reg error interrupts
  drm/amdgpu/gfx8: enable cp inst/reg error interrupts
  ...

Pull power management and ACPI fixes from Rafael Wysocki:
 "These are: a fix for a recently introduced false-positive warnings
  about PM domain pointers being changed inappropriately (harmless but
  annoying), an MCH size workaround quirk for one more platform, a
  compiler warning fix (generic power domains framework), an ACPI LPSS
  (Intel SoCs) driver fixup and a cleanup of the ACPI CPPC core code.

  Specifics:

   - PM core fix to avoid false-positive warnings generated when the
     pm_domain field is cleared for a device that appears to be bound to
     a driver (Rafael Wysocki).

   - New MCH size workaround quirk for Intel Haswell-ULT (Josh Boyer).

   - Fix for an "unused function" compiler warning in the generic power
     domains framework (Ulf Hansson).

   - Fixup for the ACPI driver for Intel SoCs (acpi-lpss) to set the PM
     domain pointer of a device properly in one place that was
     overlooked by a recent PM core update (Andy Shevchenko).

   - Removal of a redundant function declaration in the ACPI CPPC core
     code (Timur Tabi)"

* tag 'pm+acpi-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: Avoid false-positive warnings in dev_pm_domain_set()
  PM / Domains: Silence compiler warning for an unused function
  ACPI / CPPC: remove redundant mbox_send_message() declaration
  ACPI / LPSS: set PM domain via helper setter
  PNP: Add Haswell-ULT to Intel MCH size workaround

In the current implementation of the EPOLLEXCLUSIVE flag (added for
4.5-rc1), if epoll waiters create different POLL* sets and register them
as exclusive against the same target fd, the current implementation will
stop waking any further waiters once it finds the first idle waiter.
This means that waiters could miss wakeups in certain cases.

For example, when we wake up a pipe for reading we do:
wake_up_interruptible_sync_poll(&pipe->wait, POLLIN | POLLRDNORM); So if
one epoll set or epfd is added to pipe p with POLLIN and a second set
epfd2 is added to pipe p with POLLRDNORM, only epfd may receive the
wakeup since the current implementation will stop after it finds any
intersection of events with a waiter that is blocked in epoll_wait().

We could potentially address this by requiring all epoll waiters that
are added to p be required to pass the same set of POLL* events.  IE the
first EPOLL_CTL_ADD that passes EPOLLEXCLUSIVE establishes the set POLL*
flags to be used by any other epfds that are added as EPOLLEXCLUSIVE.
However, I think it might be somewhat confusing interface as we would
have to reference count the number of users for that set, and so
userspace would have to keep track of that count, or we would need a
more involved interface.  It also adds some shared state that we'd have
store somewhere.  I don't think anybody will want to bloat
__wait_queue_head for this.

I think what we could do instead, is to simply restrict EPOLLEXCLUSIVE
such that it can only be specified with EPOLLIN and/or EPOLLOUT.  So
that way if the wakeup includes 'POLLIN' and not 'POLLOUT', we can stop
once we hit the first idle waiter that specifies the EPOLLIN bit, since
any remaining waiters that only have 'POLLOUT' set wouldn't need to be
woken.  Likewise, we can do the same thing if 'POLLOUT' is in the wakeup
bit set and not 'POLLIN'.  If both 'POLLOUT' and 'POLLIN' are set in the
wake bit set (there is at least one example of this I saw in fs/pipe.c),
then we just wake the entire exclusive list.  Having both 'POLLOUT' and
'POLLIN' both set should not be on any performance critical path, so I
think that's ok (in fs/pipe.c its in pipe_release()).  We also continue
to include EPOLLERR and EPOLLHUP by default in any exclusive set.  Thus,
the user can specify EPOLLERR and/or EPOLLHUP but is not required to do
so.

Since epoll waiters may be interested in other events as well besides
EPOLLIN, EPOLLOUT, EPOLLERR and EPOLLHUP, these can still be added by
doing a 'dup' call on the target fd and adding that as one normally
would with EPOLL_CTL_ADD.  Since I think that the POLLIN and POLLOUT
events are what we are interest in balancing, I think that the 'dup'
thing could perhaps be added to only one of the waiter threads.
However, I think that EPOLLIN, EPOLLOUT, EPOLLERR and EPOLLHUP should be
sufficient for the majority of use-cases.

Since EPOLLEXCLUSIVE is intended to be used with a target fd shared
among multiple epfds, where between 1 and n of the epfds may receive an
event, it does not satisfy the semantics of EPOLLONESHOT where only 1
epfd would get an event.  Thus, it is not allowed to be specified in
conjunction with EPOLLEXCLUSIVE.

EPOLL_CTL_MOD is also not allowed if the fd was previously added as
EPOLLEXCLUSIVE.  It seems with the limited number of flags to not be as
interesting, but this could be relaxed at some further point.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Tested-by: Madars Vitolins <m@silodev.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>