The mute and mic-mute LEDs on HP ZBook Studio G5 are controlled via
GPIO bits 0x10 and 0x20, respectively, and we need the extra setup for
those.

As the similar code is already present for other HP models but with
different GPIO pins, this patch factors out the common helper code and
applies those GPIO values for each model.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211893
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210306095018.11746-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too.  Apply the
workaround generically for devices with the vendor ID 0x047f.

Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182552
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304085009.4770-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Dell AE515 sound bar (413c:a506) spews the error messages when the
driver tries to read the current sample frequency, hence it needs to
be on the list in snd_usb_get_sample_rate_quirk().

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211551
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304083021.2152-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

On some Lenovo systems if the microphone is disabled in the BIOS
only the NHLT table header is created, with no data. This means
the endpoints field is not correctly set to zero - leading to an
unintialised variable and hence invalid descriptors are parsed
leading to page faults.

The Lenovo firmware team is addressing this, but adding a check
preventing invalid tables being parsed is worthwhile.

Tested on a Lenovo T14.
Tested-by: Philipp Leskovitz <philipp.leskovitz@secunet.com>
Reported-by: Philipp Leskovitz <philipp.leskovitz@secunet.com>
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302141003.7342-1-markpearson@lenovo.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c436 ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[    6.013526] usbcore: registered new interface driver snd-usb-audio
[    6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[    6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[    6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[    6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[    6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[    6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[    6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4

I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.

Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.

Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.

Fixes: 1965c436 ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The microphone in the Plantronics C320-M headset will randomly
fail to initialize properly, at least when using Microsoft Teams.
Introducing a 20ms delay on the control messages appears to
resolve the issue.

Link: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/1065Tested-by: Andreas Kempe <kempe@lysator.liu.se>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303181405.39835-1-john.ernberg@actia.seSigned-off-by: Takashi Iwai <tiwai@suse.de>

There is another MSI board (1462:cc34) that has dual Realtek codecs,
and we need to apply the existing quirk for fixing the conflicts of
Master control.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211743
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303142346.28182-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

This adds a new SND_PCI_QUIRK(...) and applies it to the Intel NUC 10
devices. This fixes the issue of the devices not having audio input and
output on the headset jack because the kernel does not recognize when
something is plugged in.

The new quirk was inspired by the quirk for the Intel NUC 8 devices, but
it turned out that the NUC 10 uses another pin. This information was
acquired by black box testing likely pins.
Co-developed-by: Eckhart Mohr <e.mohr@tuxedocomputers.com>
Signed-off-by: Eckhart Mohr <e.mohr@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210302180414.23194-1-wse@tuxedocomputers.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

If the platform set the dyn_pcm_assign to true, it will call
hdmi_find_pcm_slot() to find a pcm slot when hdmi/dp monitor is
connected and need to create a pcm.

So far only intel_hsw_common_init() and patch_nvhdmi() set the
dyn_pcm_assign to true, here we let tgl platforms assign the pcm slot
dynamically first, if the driver runs for a period of time and there
is no regression reported, we could set no_fixed_assgin to true in
the intel_hsw_common_init(), and then set it to true in the
patch_nvhdmi().

This change comes from the discussion between Takashi and
Kai Vehmanen. Please refer to:
https://github.com/alsa-project/alsa-lib/pull/118Suggested-and-reviewed-by: Takashi Iwai <tiwai@suse.de>
Suggested-and-reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210301111202.2684-1-hui.wang@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

This applies a SND_PCI_QUIRK(...) to the Clevo NH55RZQ barebone. This
fixes the issue of the device not recognizing a pluged in microphone.

The device has both, a microphone only jack, and a speaker + microphone
combo jack. The combo jack already works. The microphone-only jack does
not recognize when a device is pluged in without this patch.
Signed-off-by: Eckhart Mohr <e.mohr@tuxedocomputers.com>
Co-developed-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/0eee6545-5169-ef08-6cfa-5def8cd48c86@tuxedocomputers.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

ALSA/ASoC/SOF/SoundWire: fix Kconfig issues

In January, Intel kbuild bot and Arnd Bergmann reported multiple
issues with randconfig. This patchset builds on Arnd's suggestions to

a) expose ACPI and PCI devices in separate modules, while sof-acpi-dev
and sof-pci-dev become helpers. This will result in minor changes
required for developers/testers, i.e. modprobe snd-sof-pci will no
longer result in a probe. The SOF CI was already updated to deal with
this module dependency change and introduction of new modules.

b) Fix SOF/SoundWire/DSP_config dependencies by moving the code
required to detect SoundWire presence in ACPI tables to sound/hda.

Link: https://lore.kernel.org/r/20210302003125.1178419-1-pierre-louis.bossart@linux.intel.com

We rely on implicit includes, list out explicitly what this code
relies on.
Suggested-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The ACPI scan capabilities is called from the intel-dspconfig as well
as the SOF/HDaudio drivers. This creates dependencies and randconfig issues
when HDaudio and SOF/SoundWire are not all configured as modules.

To simplify Kconfig dependencies between HDAudio, SoundWire, SOF and
intel-dspconfig, move the ACPI scan helpers to a dedicated
module. This follows the same idea as NHLT helpers which are already
handled as a dedicated module.

The only functional change is that the kernel parameter to filter
links is now handled by a different module, but that was only provided
for developers needing work-arounds for early BIOS releases.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Kconfig file is way too convoluted. Track platforms where
SoundWire is supported, and add simpler conditions to make sure there
is no module/built-in issue.

The use of 'depends on' is less intuitive if a required 'depend' is
missing, but that's a small price to pay for clarity and simplicity.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

There is no reason why we should call the intel_dspcfg helpers from
common code, this should be moved in Intel-specific code and only
called from platforms where a conflict may occur with the HDaudio or
SST/Skylake driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Move PCI IDs and device-specific definitions out of common code. No
functionality change for now, just code split and removal of
IF_ENABLED() which made the configurations too complicated in case of
reuse of IP across generations.

Additional changes to address the DSP_CONFIG case and SoundWire
depends/select confusions are provided in follow-up patches.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The SOF-ACPI driver is backwards from the normal Linux model, it has a
generic driver that knows about all the specific drivers, as opposed to
having hardware specific drivers that link against a common framework.

This requires ugly Kconfig magic and leads to missed dependencies as
seen in this link error:

arm-linux-gnueabi-ld: sound/soc/sof/sof-pci-dev.o: in function `sof_acpi_probe':
sof-pci-dev.c:(.text+0x1c): undefined reference to `snd_intel_dsp_driver_probe'

Change it to use the normal probe order of starting with a specific
device in a driver, turning the sof-acpi-dev.c driver into a
library (exported symbols are name-spaced to avoid symbol pollution).

For backwards-compatibility with previous Kconfigs, the default values
for platform drivers uses the top-level ACPI configurations. The
modules were also renamed to allow for gradual transitions in test
scripts.
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

To change the module dependencies and simplify Kconfigs, we need to
introduce new driver names (sof-audio-acpi-intel-byt and
sof-audio-acpi-intel-bdw), and move from an exact string match to a
partial one.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210302003125.1178419-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Multiple bug reports report issues with the SOF and SST drivers when
dealing with single microphone cases.

We currently read the DMIC array information unconditionally but we
don't check that the configuration type is actually a mic array.

When the DMIC link does not rely on a mic array configuration, the
recommendation is to check the format information to infer the maximum
number of channels, and map this to the number of microphones.

This leaves a potential for a mismatch between actual microphones
available in hardware and what the ACPI table contains, but we have no
other source of information.

Note that single microphone configurations can alternatively be
handled with a 'mic array' configuration along with a 'vendor-defined'
geometry.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201251
BugLink: https://github.com/thesofproject/linux/issues/2725
Fixes: 7a33ea70 ('ALSA: hda: intel-nhlt: handle NHLT VENDOR_DEFINED DMIC geometry')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210302000146.1177770-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

v5.12-rc1 flags new warnings with make W=1, fix missing or broken
function descriptors.

sound/pci/hda/hda_codec.c:3492: warning: expecting prototype for
snd_hda_input_mux_info_info(). Prototype was for
snd_hda_input_mux_info() instead

sound/pci/hda/hda_codec.c:3521: warning: expecting prototype for
snd_hda_input_mux_info_put(). Prototype was for
snd_hda_input_mux_put() instead

sound/pci/hda/hda_codec.c:3958: warning: expecting prototype for
_snd_hda_pin_ctl(). Prototype was for _snd_hda_set_pin_ctl() instead

sound/pci/hda/hda_jack.c:223: warning: expecting prototype for
snd_hda_set_dirty_all(). Prototype was for
snd_hda_jack_set_dirty_all() instead

sound/pci/hda/hda_jack.c:309: warning: expecting prototype for
snd_hda_jack_detect_enable_mst(). Prototype was for
snd_hda_jack_detect_enable_callback_mst() instead

sound/pci/hda/hda_generic.c:3933: warning: expecting prototype for
snd_dha_gen_add_mute_led_cdev(). Prototype was for
snd_hda_gen_add_mute_led_cdev() instead

sound/pci/hda/hda_generic.c:4093: warning: expecting prototype for
snd_dha_gen_add_micmute_led_cdev(). Prototype was for
snd_hda_gen_add_micmute_led_cdev() instead

sound/pci/hda/patch_ca0132.c:2357: warning: expecting prototype for
Prepare and send the SCP message to DSP(). Prototype was for
dspio_scp() instead

sound/pci/hda/patch_ca0132.c:2883: warning: expecting prototype for
Allocate router ports(). Prototype was for dsp_allocate_router_ports()
instead

sound/pci/hda/patch_ca0132.c:3202: warning: expecting prototype for
Write a block of data into DSP code or data RAM using pre(). Prototype
was for dspxfr_one_seg() instead

sound/pci/hda/patch_ca0132.c:3397: warning: expecting prototype for
data overlay to DSP memories(). Prototype was for dspxfr_image()
instead

sound/hda/hdac_regmap.c:393: warning: expecting prototype for
snd_hdac_regmap_init(). Prototype was for snd_hdac_regmap_exit()
instead

sound/hda/ext/hdac_ext_controller.c:142: warning: expecting prototype
for snd_hdac_ext_bus_get_link_index(). Prototype was for
snd_hdac_ext_bus_get_link() instead

sound/hda/ext/hdac_ext_stream.c:140: warning: expecting prototype for
snd_hdac_ext_linkstream_start(). Prototype was for
snd_hdac_ext_link_stream_start() instead
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210301174617.116960-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

This commit only contains the fix about the `URB_CONTROL` request
direction to set the samplerate of Pioneer DJM devices (`URB_CONTROL out`).

Fixes: 3b85f5fc ("ALSA: usb-audio: Add DJM450 to Pioneer format quirk")
Signed-off-by: Nicolas MURE <nicolas.mure2019@gmail.com>
Link: https://lore.kernel.org/r/20210301142927.14552-1-nicolas.mure2019@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
Signed-off-by: Andrea Fagiani <andfagiani@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/40bbdf55-f854-e2ee-87b4-183e6451352c@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Pull ide fix from Jens Axboe:
 "This is a leftover fix from 5.11, where I forgot to ship it your way"

* tag 'ide-5.11-2021-02-28' of git://git.kernel.dk/linux-block:
  ide/falconide: Fix module unload

Merge tag 'kbuild-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix UNUSED_KSYMS_WHITELIST for Clang LTO

 - Make -s builds really silent irrespective of V= option

 - Fix build error when SUBLEVEL or PATCHLEVEL is empty

* tag 'kbuild-fixes-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: Fix <linux/version.h> for empty SUBLEVEL or PATCHLEVEL again
  kbuild: make -s option take precedence over V=1
  ia64: remove redundant READELF from arch/ia64/Makefile
  kbuild: do not include include/config/auto.conf from adjust_autoksyms.sh
  kbuild: fix UNUSED_KSYMS_WHITELIST for Clang LTO
  kbuild: lto: add _mcount to list of used symbols

Pull arch/csky updates from Guo Ren:
 "Features:
   - add new memory layout 2.5G(user):1.5G(kernel)
   - add kmemleak support
   - reconstruct VDSO framework: add VDSO with GENERIC_GETTIMEOFDAY,
     GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
   - add faulthandler_disabled() check
   - support (fix) swapon
   - add (fix) _PAGE_ACCESSED for default pgprot
   - abort uaccess retries upon fatal signal (from arm)

  Fixes and optimizations:
   - fix perf probe failure
   - fix show_regs doesn't contain regs->usp
   - remove custom asm/atomic.h implementation
   - fix barrier design
   - fix futex SMP implementation
   - fix asm/cmpxchg.h with correct ordering barrier
   - cleanup asm/spinlock.h
   - fix PTE global for 2.5:1.5 virtual memory
   - remove prologue of page fault handler in entry.S
   - fix TLB maintenance synchronization problem
   - add show_tlb for CPU_CK860 debug
   - fix FAULT_FLAG_XXX param for handle_mm_fault
   - fix update_mmu_cache called with user io mapping
   - fix do_page_fault parent irq status
   - fix a size determination in gpr_get()
   - pgtable.h: Coding convention
   - kprobe: Fix code in simulate without 'long'
   - fix pfn_valid error with wrong max_mapnr
   - use free_initmem_default() in free_initmem()
   - fix compile error"

* tag 'csky-for-linus-5.12-rc1' of git://github.com/c-sky/csky-linux: (30 commits)
  csky: Fixup compile error
  csky: use free_initmem_default() in free_initmem()
  csky: Fixup pfn_valid error with wrong max_mapnr
  csky: Add VDSO with GENERIC_GETTIMEOFDAY, GENERIC_TIME_VSYSCALL, HAVE_GENERIC_VDSO
  csky: kprobe: Fixup code in simulate without 'long'
  csky: Fixup swapon
  csky: pgtable.h: Coding convention
  csky: Fixup _PAGE_ACCESSED for default pgprot
  csky: remove unused including <linux/version.h>
  csky: Fix a size determination in gpr_get()
  csky: Reconstruct VDSO framework
  csky: mm: abort uaccess retries upon fatal signal
  csky: Sync riscv mm/fault.c for easy maintenance
  csky: Fixup do_page_fault parent irq status
  csky: Add faulthandler_disabled() check
  csky: Fixup update_mmu_cache called with user io mapping
  csky: Fixup FAULT_FLAG_XXX param for handle_mm_fault
  csky: Add show_tlb for CPU_CK860 debug
  csky: Fix TLB maintenance synchronization problem
  csky: Add kmemleak support
  ...

Pull more RISC-V updates from Palmer Dabbelt:
 "A pair of patches that slipped through the cracks:

   - enable CPU hotplug in the defconfigs

   - some cleanups to setup_bootmem

  There's also a single fix for some randconfig build failures:

   - make NUMA depend on SMP"

* tag 'riscv-for-linus-5.12-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Cleanup setup_bootmem()
  RISC-V: Enable CPU Hotplug in defconfigs
  RISC-V: Make NUMA depend on SMP

Pull more SCSI updates from James Bottomley:
 "This is a few driver updates (iscsi, mpt3sas) that were still in the
  staging queue when the merge window opened (all committed on or before
  8 Feb) and some small bug fixes which came in during the merge window
  (all committed on 22 Feb)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
  scsi: hpsa: Correct dev cmds outstanding for retried cmds
  scsi: sd: Fix Opal support
  scsi: target: tcmu: Fix memory leak caused by wrong uio usage
  scsi: target: tcmu: Move some functions without code change
  scsi: sd: sd_zbc: Don't pass GFP_NOIO to kvcalloc
  scsi: aic7xxx: Remove unused function pointer typedef ahc_bus_suspend/resume_t
  scsi: bnx2fc: Fix Kconfig warning & CNIC build errors
  scsi: ufs: Fix a duplicate dev quirk number
  scsi: aic79xx: Fix spelling of version
  scsi: target: core: Prevent underflow for service actions
  scsi: target: core: Add cmd length set before cmd complete
  scsi: iscsi: Drop session lock in iscsi_session_chkready()
  scsi: qla4xxx: Use iscsi_is_session_online()
  scsi: libiscsi: Reset max/exp cmdsn during recovery
  scsi: iscsi_tcp: Fix shost can_queue initialization
  scsi: libiscsi: Add helper to calculate max SCSI cmds per session
  scsi: libiscsi: Fix iSCSI host workq destruction
  scsi: libiscsi: Fix iscsi_task use after free()
  scsi: libiscsi: Drop taskqueuelock
  scsi: libiscsi: Fix iscsi_prep_scsi_cmd_pdu() error handling
  ...

Pull more xfs updates from Darrick Wong:
 "The most notable fix here prevents premature reuse of freed metadata
  blocks, and adding the ability to detect accidental nested
  transactions, which are not allowed here.

   - Restore a disused sysctl control knob that was inadvertently
     dropped during the merge window to avoid fstests regressions.

   - Don't speculatively release freed blocks from the busy list until
     we're actually allocating them, which fixes a rare log recovery
     regression.

   - Don't nest transactions when scanning for free space.

   - Add an idiot^Wmaintainer light to detect nested transactions. ;)"

* tag 'xfs-5.12-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: use current->journal_info for detecting transaction recursion
  xfs: don't nest transactions when scanning for eofblocks
  xfs: don't reuse busy extents on extent trim
  xfs: restore speculative_cow_prealloc_lifetime sysctl

Pull more block updates from Jens Axboe:
 "A few stragglers (and one due to me missing it originally), and fixes
  for changes in this merge window mostly. In particular:

   - blktrace cleanups (Chaitanya, Greg)

   - Kill dead blk_pm_* functions (Bart)

   - Fixes for the bio alloc changes (Christoph)

   - Fix for the partition changes (Christoph, Ming)

   - Fix for turning off iopoll with polled IO inflight (Jeffle)

   - nbd disconnect fix (Josef)

   - loop fsync error fix (Mauricio)

   - kyber update depth fix (Yang)

   - max_sectors alignment fix (Mikulas)

   - Add bio_max_segs helper (Matthew)"

* tag 'block-5.12-2021-02-27' of git://git.kernel.dk/linux-block: (21 commits)
  block: Add bio_max_segs
  blktrace: fix documentation for blk_fill_rw()
  block: memory allocations in bounce_clone_bio must not fail
  block: remove the gfp_mask argument to bounce_clone_bio
  block: fix bounce_clone_bio for passthrough bios
  block-crypto-fallback: use a bio_set for splitting bios
  block: fix logging on capacity change
  blk-settings: align max_sectors on "logical_block_size" boundary
  block: reopen the device in blkdev_reread_part
  block: don't skip empty device in in disk_uevent
  blktrace: remove debugfs file dentries from struct blk_trace
  nbd: handle device refs for DESTROY_ON_DISCONNECT properly
  kyber: introduce kyber_depth_updated()
  loop: fix I/O error on fsync() in detached loop devices
  block: fix potential IO hang when turning off io_poll
  block: get rid of the trace rq insert wrapper
  blktrace: fix blk_rq_merge documentation
  blktrace: fix blk_rq_issue documentation
  blktrace: add blk_fill_rwbs documentation comment
  block: remove superfluous param in blk_fill_rwbs()
  ...

The Acer SWIFT Swift SF314-54/55 laptops with ALC256 cannot detect
both the headset mic and the internal mic. Introduce new fixup
to enable the jack sense and the headset mic. However, the internal
mic actually connects to Intel SST audio. It still needs Intel SST
support to make internal mic capture work.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210226010440.8474-1-chris.chiu@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Currently the mask operation on variable conf is just 3 bits so
the switch statement case value of 8 is unreachable dead code.
The function daio_mgr_dao_init can be passed a 4 bit value,
function dao_rsc_init calls it with conf set to:

     conf = (desc->msr & 0x7) | (desc->passthru << 3);

so clearly when desc->passthru is set to 1 then conf can be
at least 8.

Fix this by changing the mask to 0xf.

Fixes: 8cc72361 ("ALSA: SB X-Fi driver merge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210227001527.1077484-1-colin.king@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The recent fix for the hw constraints for implicit feedback streams
via commit e4ea77f8 ("ALSA: usb-audio: Always apply the hw
constraints for implicit fb sync") added the check of the matching
endpoints and whether those EPs are already opened.  This is needed
and correct, per se, even for the normal streams without the implicit
feedback, as the endpoint setup is exclusive.

However, it's reported that there seem applications that behave in
unexpected ways to update the hw_params without clearing the previous
setup via hw_free, and those hit a problem now: then hw_params is
called with still the previous EP setup kept, hence it's restricted
with the previous own setup.  Although the obvious fix is to call
snd_pcm_hw_free() API in the application side, it's a kind of
unwelcome change.

This patch tries to ease the situation: in the endpoint check, we add
a couple of more conditions and now skip the endpoint that is being
used only by the stream in question itself.  That is, in addition to
the presence check of ep (ep->cur_audiofmt is non-NULL), when the
following conditions are met, we skip such an ep:
- ep->opened == 1, and
- ep->cur_audiofmt == subs->cur_audiofmt.

subs->cur_audiofmt is non-NULL only if it's a re-setup of hw_params,
and ep->cur_audiofmt points to the currently set up parameters.  So if
those match, it must be this stream itself.

Fixes: e4ea77f8 ("ALSA: usb-audio: Always apply the hw constraints for implicit fb sync")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211941
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210228080138.9936-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

Commit 78d3bb44 ("kbuild: Fix <linux/version.h> for empty SUBLEVEL
or PATCHLEVEL") fixed the build error for empty SUBLEVEL or PATCHLEVEL
by prepending a zero.

Commit 9b82f13e ("kbuild: clamp SUBLEVEL to 255") re-introduced
this issue.

This time, we cannot take the same approach because we have C code:

  #define LINUX_VERSION_PATCHLEVEL $(PATCHLEVEL)
  #define LINUX_VERSION_SUBLEVEL $(SUBLEVEL)

Replace empty SUBLEVEL/PATCHLEVEL with a zero.

Fixes: 9b82f13e ("kbuild: clamp SUBLEVEL to 255")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-and-tested-by: Sasha Levin <sashal@kernel.org>

'make -s' should be really silent. However, 'make -s V=1' prints noisy
log messages from some shell scripts.

Of course, such a combination is odd, but the build system needs to do
the right thing even if a user gives strange input.

If -s is given, KBUILD_VERBOSE should be forced to 0.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

READELF is defined by the top Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Commit cd195bc4 ("kbuild: split adjust_autoksyms.sh in two parts")
split out the code that needs include/config/auto.conf.

This script no longer needs to include include/config/auto.conf.

Fixes: cd195bc4 ("kbuild: split adjust_autoksyms.sh in two parts")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Commit fbe078d3 ("kbuild: lto: add a default list of used symbols")
does not work as expected if the .config file has already specified
CONFIG_UNUSED_KSYMS_WHITELIST="my/own/white/list" before enabling
CONFIG_LTO_CLANG.

So, the user-supplied whitelist and LTO-specific white list must be
independent of each other.

I refactored the shell script so CONFIG_MODVERSIONS and CONFIG_CLANG_LTO
handle whitelists in the same way.

Fixes: fbe078d3 ("kbuild: lto: add a default list of used symbols")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>

Pull io_uring thread rewrite from Jens Axboe:
 "This converts the io-wq workers to be forked off the tasks in question
  instead of being kernel threads that assume various bits of the
  original task identity.

  This kills > 400 lines of code from io_uring/io-wq, and it's the worst
  part of the code. We've had several bugs in this area, and the worry
  is always that we could be missing some pieces for file types doing
  unusual things (recent /dev/tty example comes to mind, userfaultfd
  reads installing file descriptors is another fun one... - both of
  which need special handling, and I bet it's not the last weird oddity
  we'll find).

  With these identical workers, we can have full confidence that we're
  never missing anything. That, in itself, is a huge win. Outside of
  that, it's also more efficient since we're not wasting space and code
  on tracking state, or switching between different states.

  I'm sure we're going to find little things to patch up after this
  series, but testing has been pretty thorough, from the usual
  regression suite to production. Any issue that may crop up should be
  manageable.

  There's also a nice series of further reductions we can do on top of
  this, but I wanted to get the meat of it out sooner rather than later.
  The general worry here isn't that it's fundamentally broken. Most of
  the little issues we've found over the last week have been related to
  just changes in how thread startup/exit is done, since that's the main
  difference between using kthreads and these kinds of threads. In fact,
  if all goes according to plan, I want to get this into the 5.10 and
  5.11 stable branches as well.

  That said, the changes outside of io_uring/io-wq are:

   - arch setup, simple one-liner to each arch copy_thread()
     implementation.

   - Removal of net and proc restrictions for io_uring, they are no
     longer needed or useful"

* tag 'io_uring-worker.v3-2021-02-25' of git://git.kernel.dk/linux-block: (30 commits)
  io-wq: remove now unused IO_WQ_BIT_ERROR
  io_uring: fix SQPOLL thread handling over exec
  io-wq: improve manager/worker handling over exec
  io_uring: ensure SQPOLL startup is triggered before error shutdown
  io-wq: make buffered file write hashed work map per-ctx
  io-wq: fix race around io_worker grabbing
  io-wq: fix races around manager/worker creation and task exit
  io_uring: ensure io-wq context is always destroyed for tasks
  arch: ensure parisc/powerpc handle PF_IO_WORKER in copy_thread()
  io_uring: cleanup ->user usage
  io-wq: remove nr_process accounting
  io_uring: flag new native workers with IORING_FEAT_NATIVE_WORKERS
  net: remove cmsg restriction from io_uring based send/recvmsg calls
  Revert "proc: don't allow async path resolution of /proc/self components"
  Revert "proc: don't allow async path resolution of /proc/thread-self components"
  io_uring: move SQPOLL thread io-wq forked worker
  io-wq: make io_wq_fork_thread() available to other users
  io-wq: only remove worker from free_list, if it was there
  io_uring: remove io_identity
  io_uring: remove any grabbing of context
  ...

Pull misc vfs updates from Al Viro:
 "Assorted stuff pile - no common topic here"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  whack-a-mole: don't open-code iminor/imajor
  9p: fix misuse of sscanf() in v9fs_stat2inode()
  audit_alloc_mark(): don't open-code ERR_CAST()
  fs/inode.c: make inode_init_always() initialize i_ino to 0
  vfs: don't unnecessarily clone write access for writable fds