1. 31 Jul, 2017 34 commits
  2. 30 Jul, 2017 4 commits
    • David S. Miller's avatar
      Merge branch 'ethtool-fec' · 736b9b9c
      David S. Miller authored
      Roopa Prabhu says:
      
      ====================
      ethtool: support for forward error correction mode setting on a link
      
      Forward Error Correction (FEC) modes i.e Base-R
      and Reed-Solomon modes are introduced in 25G/40G/100G standards
      for providing good BER at high speeds. Various networking devices
      which support 25G/40G/100G provides ability to manage supported FEC
      modes and the lack of FEC encoding control and reporting today is a
      source for interoperability issues for many vendors.
      FEC capability as well as specific FEC mode i.e. Base-R
      or RS modes can be requested or advertised through bits D44:47 of base link
      codeword.
      
      This patch set intends to provide option under ethtool to manage and
      report FEC encoding settings for networking devices as per IEEE 802.3
      bj, bm and by specs.
      
      v2 :
              - minor patch format fixes and typos pointed out by Andrew
              - there was a pending discussion on the use of 'auto' vs
                'automatic' for fec settings. I have left it as 'auto'
                because in most cases today auto is used in place of
                automatic to represent automatically generated values.
                We use it in other networking config too. I would prefer
                leaving it as auto.
      ====================
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      736b9b9c
    • Casey Leedom's avatar
    • Casey Leedom's avatar
    • Vidya Sagar Ravipati's avatar
      net: ethtool: add support for forward error correction modes · 1a5f3da2
      Vidya Sagar Ravipati authored
      Forward Error Correction (FEC) modes i.e Base-R
      and Reed-Solomon modes are introduced in 25G/40G/100G standards
      for providing good BER at high speeds. Various networking devices
      which support 25G/40G/100G provides ability to manage supported FEC
      modes and the lack of FEC encoding control and reporting today is a
      source for interoperability issues for many vendors.
      FEC capability as well as specific FEC mode i.e. Base-R
      or RS modes can be requested or advertised through bits D44:47 of
      base link codeword.
      
      This patch set intends to provide option under ethtool to manage
      and report FEC encoding settings for networking devices as per
      IEEE 802.3 bj, bm and by specs.
      
      set-fec/show-fec option(s) are designed to provide control and
      report the FEC encoding on the link.
      
      SET FEC option:
      root@tor: ethtool --set-fec  swp1 encoding [off | RS | BaseR | auto]
      
      Encoding: Types of encoding
      Off    :  Turning off any encoding
      RS     :  enforcing RS-FEC encoding on supported speeds
      BaseR  :  enforcing Base R encoding on supported speeds
      Auto   :  IEEE defaults for the speed/medium combination
      
      Here are a few examples of what we would expect if encoding=auto:
      - if autoneg is on, we are  expecting FEC to be negotiated as on or off
        as long as protocol supports it
      - if the hardware is capable of detecting the FEC encoding on it's
            receiver it will reconfigure its encoder to match
      - in absence of the above, the configuration would be set to IEEE
        defaults.
      
      >From our  understanding , this is essentially what most hardware/driver
      combinations are doing today in the absence of a way for users to
      control the behavior.
      
      SHOW FEC option:
      root@tor: ethtool --show-fec  swp1
      FEC parameters for swp1:
      Active FEC encodings: RS
      Configured FEC encodings:  RS | BaseR
      
      ETHTOOL DEVNAME output modification:
      
      ethtool devname output:
      root@tor:~# ethtool swp1
      Settings for swp1:
      root@hpe-7712-03:~# ethtool swp18
      Settings for swp18:
          Supported ports: [ FIBRE ]
          Supported link modes:   40000baseCR4/Full
                                  40000baseSR4/Full
                                  40000baseLR4/Full
                                  100000baseSR4/Full
                                  100000baseCR4/Full
                                  100000baseLR4_ER4/Full
          Supported pause frame use: No
          Supports auto-negotiation: Yes
          Supported FEC modes: [RS | BaseR | None | Not reported]
          Advertised link modes:  Not reported
          Advertised pause frame use: No
          Advertised auto-negotiation: No
          Advertised FEC modes: [RS | BaseR | None | Not reported]
      <<<< One or more FEC modes
          Speed: 100000Mb/s
          Duplex: Full
          Port: FIBRE
          PHYAD: 106
          Transceiver: internal
          Auto-negotiation: off
          Link detected: yes
      
      This patch includes following changes
      a) New ETHTOOL_SFECPARAM/SFECPARAM API, handled by
        the new get_fecparam/set_fecparam callbacks, provides support
        for configuration of forward error correction modes.
      b) Link mode bits for FEC modes i.e. None (No FEC mode), RS, BaseR/FC
        are defined so that users can configure these fec modes for supported
        and advertising fields as part of link autonegotiation.
      Signed-off-by: default avatarVidya Sagar Ravipati <vidya.chowdary@gmail.com>
      Signed-off-by: default avatarDustin Byford <dustin@cumulusnetworks.com>
      Signed-off-by: default avatarRoopa Prabhu <roopa@cumulusnetworks.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1a5f3da2
  3. 29 Jul, 2017 2 commits