- 29 Aug, 2016 10 commits
-
-
Vidya Sagar Ravipati authored
This patch enhances ethtool link mode bitmap to include missing interface modes for 1G/10G speeds Changes: 1000baseX is the mode introduced to cover all 1G Fiber cases. All modes under 1000BaseX i.e. 1000BASE-SX, 1000BASE-LX, 1000BASE-LX10 and 1000BASE-BX10 are not explicitly defined at this moment. 10G CR,SR,LR and ER link modes are included for 10G speed.. Issue: ethtool on 1G/10G SFP port reports Base-T as this port supports 1000baseX,10G CR, SR and LR modes. root@tor-02$ ethtool swp1 Settings for swp1: Supported ports: [ FIBRE ] Supported link modes: 1000baseT/Full 10000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: off Current message level: 0x00000000 (0) Link detected: yes After fix: root@tor-02$ ethtool swp1 Settings for swp1: Supported ports: [ FIBRE ] Supported link modes: 1000baseX/Full 10000baseCR/Full 10000baseSR/Full 10000baseLR/Full 10000baseER/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Advertised link modes: 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: off Current message level: 0x00000000 (0) Link detected: yes Signed-off-by:Vidya Sagar Ravipati <vidya@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
James Morse authored
After resume from hibernate on arm64, any amd-xgbe devices that were running when we hibernated are reported as down, even when it is not. Re-plugging the cables does not cause the interface to come back, the link must be marked as down then up via 'ip set link' using the serial console. This happens because the device has been power-cycled and possibly re-initialised by firmware, whereas the driver's memory structures have been restored from the hibernate image and the two do not agree. Schedule a restart of the device after powerup in case the world changed while we were asleep. Signed-off-by:
James Morse <james.morse@arm.com> Signed-off-by:
-
Eric Dumazet authored
When TCP operates in lossy environments (between 1 and 10 % packet losses), many SACK blocks can be exchanged, and I noticed we could drop them on busy senders, if these SACK blocks have to be queued into the socket backlog. While the main cause is the poor performance of RACK/SACK processing, we can try to avoid these drops of valuable information that can lead to spurious timeouts and retransmits. Cause of the drops is the skb->truesize overestimation caused by : - drivers allocating ~2048 (or more) bytes as a fragment to hold an Ethernet frame. - various pskb_may_pull() calls bringing the headers into skb->head might have pulled all the frame content, but skb->truesize could not be lowered, as the stack has no idea of each fragment truesize. The backlog drops are also more visible on bidirectional flows, since their sk_rmem_alloc can be quite big. Let's add some room for the backlog, as only the socket owner can selectively take action to lower memory needs, like collapsing receive queues or partial ofo pruning. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dev_warn message. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dev_warn message. Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in dev_err message. Signed-off-by:
-
David S. Miller authored
Tom Herbert says: ==================== strp: Generalize stream parser to work with other socket types Add a read_sock protocol operation function that allows something like tcp_read_sock to be called for other protocol types. Specific changes in this patch set: - Add read_sock function to proto_ops. This has the same signature as tcp_read_sock. sk_read_actor_t is also defined in net.h. - Set peek_len and read_sock proto_op functions for TCPv4 and TCPv6 stream ops. - Remove references to tcp in strparser. - Call peek_len and read_sock operations from strparser instead of calling TCP specific functions. ==================== Signed-off-by: -
Tom Herbert authored
kcm and strparser need to work with any type of stream socket not just TCP. Eliminate references to TCP and call generic proto_ops functions of read_sock and peek_len. Also in strp_init check if the socket support the proto_ops read_sock and peek_len. Signed-off-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
Tom Herbert authored
In inet_stream_ops we set read_sock to tcp_read_sock and peek_len to tcp_peek_len (which is just a stub function that calls tcp_inq). Signed-off-by:
-
Tom Herbert authored
Add new function in proto_ops structure. This includes moving the typedef got sk_read_actor into net.h and removing the definition from tcp.h. Signed-off-by:
-
- 27 Aug, 2016 19 commits
-
-
Wei Yongjun authored
Fix to return a negative error code from the cpsw_fill_rx_channels() error handling case instead of 0, as done elsewhere in this function. Fixes: ce52c744 ("net: ethernet: ti: cpsw: add ethtool channels support") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Zhu Yanjun authored
This header file is not used in vxlan.c file. Signed-off-by:
Zhu Yanjun <zyjzyj2000@gmail.com> Signed-off-by:
-
Wei Yongjun authored
Fixes the following sparse warning: drivers/crypto/chelsio/chcr_algo.c:593:5: warning: symbol 'cxgb4_is_crypto_q_full' was not declared. Should it be static? Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Jon Cooper authored
MC_CMD_TRIGGER_INTERRUPT does not work on the SFC9140, as used in the sfn7x42q and sfn7x24f. Check for this using the MCDI workaround mechanism. The command is only used during self test. If it's not supported, skip the interrupt test. Signed-off-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Edward Cree authored
nic_data was already initialised to the right thing, no need to assign it again. Signed-off-by:
-
Edward Cree authored
TX size bins were not supported on the 7000's 40G MAC, but the 8000 series does support them and the MCPU advertises that via a new capability bit. Signed-off-by:
-
David S. Miller authored
Richard Alpe says: ==================== tipc: introduce UDP replicast This series introduces UDP replicast. A concept where we emulate multicast by sending multiple unicast messages to configured peers. This allows TIPC to be used in environments where IP multicast is disabled. There is a corresponding patch series for the tipc user space tool that allows a user to add remote addresses to the replicast list. ==================== Signed-off-by: -
Richard Alpe authored
When using replicast a UDP bearer can have an arbitrary amount of remote ip addresses associated with it. This means we cannot simply add all remote ip addresses to an existing bearer data message as it might fill the message, leaving us with a truncated message that we can't safely resume. To handle this we introduce the new netlink command TIPC_NL_UDP_GET_REMOTEIP. This command is intended to be called when the bearer data message has the TIPC_NLA_UDP_MULTI_REMOTEIP flag set, indicating there are more than one remote ip (replicast). Signed-off-by:
Richard Alpe <richard.alpe@ericsson.com> Reviewed-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Richard Alpe authored
Add UDP bearer options to netlink bearer get message. This is used by the tipc user space tool to display UDP options. The UDP bearer information is passed using either a sockaddr_in or sockaddr_in6 structs. This means the user space receiver should intermediately store the retrieved data in a large enough struct (sockaddr_strage) before casting to the proper IP version type. Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Richard Alpe authored
Automatically learn UDP remote IP addresses of communicating peers by looking at the source IP address of incoming TIPC link configuration messages (neighbor discovery). This makes configuration slightly easier and removes the problematic scenario where a node receives directly addressed neighbor discovery messages sent using replicast which the node cannot "reply" to using mutlicast, leaving the link FSM in a limbo state. Signed-off-by:
-
Richard Alpe authored
This patch introduces UDP replicast. A concept where we emulate multicast by sending multiple unicast messages to configured peers. The purpose of replicast is mainly to be able to use TIPC in cloud environments where IP multicast is disabled. Using replicas to unicast multicast messages is costly as we have to copy each skb and send the copies individually. Signed-off-by:
-
Richard Alpe authored
Add a function to check if a tipc UDP media address is a multicast address or not. This is a purely cosmetic change. Signed-off-by:
-
Richard Alpe authored
Split the UDP send function into two. One callback that prepares the skb and one transmit function that sends the skb. This will come in handy in later patches, when we introduce UDP replicast. Signed-off-by:
-
Richard Alpe authored
Split the UDP netlink parse function so that it only parses one netlink attribute at the time. This makes the parse function more generic and allow future UDP API functions to use it for parsing. Signed-off-by:
-
Florian Fainelli authored
And while at it, remove the unecessary writing of zeroes to the CPU_MASK_CLEAR register since it has no functional use. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Tobias Regnery authored
Add tso/tso6 support to the alx driver. Based on information from the downstream driver at github.com/qca/alx Signed-off-by:
Tobias Regnery <tobias.regnery@gmail.com> Signed-off-by:
-
David S. Miller authored
Nelson Chang says: ==================== net: ethernet: mediatek: modify to use the PDMA for Ethernet RX This series have some modifications and refines to support Ethernet RX by the PDMA. changes since v4: - Remove the redundant OR operation in mtk_hw_init() changes since v3: - Add GDM hardware settings to send packets to PDMA for RX changes since v2: - Fix the bugs of PDMA cpu index and interrupt settings in mtk_poll_rx() changes since v1: - Modify to use the PDMA instead of the QDMA for Ethernet RX ==================== Signed-off-by: -
Nelson Chang authored
Because we change to use the PDMA as the Ethernet RX DMA engine, the patch modifies to set GDM to send packets to PDMA for RX. Acked-by:
John Crispin <john@phrozen.org> Signed-off-by:
Nelson Chang <nelson.chang@mediatek.com> Signed-off-by:
-
Nelson Chang authored
Because the PDMA has richer features than the QDMA for Ethernet RX (such as multiple RX rings, HW LRO, etc.), the patch modifies to use the PDMA to handle Ethernet RX. Acked-by:
-
- 26 Aug, 2016 11 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: dsa: Make bcm_sf2 utilize b53_common This patch series makes the bcm_sf2 driver utilize a large number of the core functions offered by the b53_common driver since the SWITCH_CORE registers are mostly register compatible with the switches driven by b53_common. In order to accomplish that, we just override the dsa_driver_ops callbacks that we need to. There are still integration specific logic from the bcm_sf2 that we cannot absorb into b53_common because it is just not there, mostly in the area of link management and power management, but most of the features are within b53_common now: VLAN, FDB, bridge Along the process, we also improve support for the BCM58xx SoCs, since those also have the same version of the switching IP that 7445 has (for which bcm_sf2 was developed). Changes in v3: - rebase against 145dd5f9 ("net: flush the softnet backlog in process context") Changes in v2: - rebased against "net: dsa: rename switch operations structure" ==================== Signed-off-by:
-
Florian Fainelli authored
Now that we are using b53_common for most VLAN, FDB and bridge operations, delete all the redundant code that we had in bcm_sf2.c to keep only the integration specific logic that we have to deal with: power management, link management and the external interfaces (RGMII, MDIO). Signed-off-by:
-
Florian Fainelli authored
The Broadcom Starfighter2 is almost entirely register compatible with B53, yet for historical reasons came up first in the tree and is now being updated to utilize b53_common.c to the fullest extent possible. A few things need to be adjusted to allow that: - the switch "core" registers currently operate on a 32-bit address, whereas b53 passes a page + reg pair to offset from, so we need to convert that, thankfully there is a generic formula to do that - the link managemenent is not self contained with the B53/CORE register set, but instead is in the SWITCH_REG block which is part of the integration glue logic, so we keep that entirely custom here because this really is part of the existing bcm_sf2 implementation - there are additional power management constraints on the port's memories that make us keep the port_enable/disable callbacks custom for now, also, we support tagging whereas b53_common does not support that yet All the VLAN and bridge code is entirely identical though so, avoid duplicating it. Other things will be migrated in the future like EEE and possibly Wake-on-LAN. Signed-off-by:
-
Florian Fainelli authored
In order to migrate the bcm_sf2 driver over to the b53 driver for most VLAN/FDB/bridge operations, we need to add support for the "join all VLANs" register and behavior which allows us to make a given port join all VLANs and avoid setting specific VLAN entries when it is leaving the bridge. Signed-off-by:
-
Florian Fainelli authored
The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout and introduce a helper function: is58xx() which checks for both of these IDs for now. Signed-off-by:
-
Florian Fainelli authored
Allocate a device entry for the Broadcom BCM7445 integrated switch currently backed by bcm_sf2.c. Since this is the latest generation, it has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port. Signed-off-by:
-
Florian Fainelli authored
In order to allow drivers to override specific dsa_switch_driver callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids having to expose this structure to glue drivers. Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Introduce support for offload forward mark Ido says: This patchset enables the forwarding of certain control packets by the device instead of relying on the CPU to do the forwarding. The first two patches simplify the current switchdev offload forward infrastructure and make it usable for stacked devices. This is done by moving the packet and port marking to the bridge driver instead of the switch driver. Patches 3-5 add the mlxsw specific bits to support the forward mark. ==================== Signed-off-by: -
Ido Schimmel authored
Instead of trapping certain packets to the CPU and then relying on it to flood them we can instead make the device mirror them. The following packet types are mirrored: * DHCP: Broadcast packets that should be flooded by the device, but also trapped in case CPU is running the DHCP server. * IGMP query: Multicast packets that need to be forwarded to other bridge ports, but also trapped so that receiving netdev will be marked as a router port by the bridge driver. * ARP request: Broadcast packets that should be forwarded to other bridge ports, but also trapped in case requested IP is of the local machine. * ARP response: Unicast packets that should be forwarded by the bridge but also trapped in case response is directed at us. Set the trap action of such packets to mirror and mark them using 'offload_fwd_mark' to prevent the bridge driver from forwarding them itself. Note that OSPF packets are also marked despite their action being trap. The reason for this is that the device traps such packets in the pipeline after they were already flooded. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
Up until now we only trapped packets to CPU, but we are going to allow some packets to be mirrored (trap & forward) to CPU. Extend the Rx listener with 'action' member. Signed-off-by:
-
Ido Schimmel authored
Instead of copying & pasting the same struct initialization for every Rx listener, just use a macro. Signed-off-by:
-
