RFC 8033 recommends a value of 16384 bytes for the queue
threshold.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Dhaval Khandla <dhavaljkhandla26@gmail.com>
Signed-off-by: Hrishikesh Hiraskar <hrishihiraskar@gmail.com>
Signed-off-by: Manish Kumar B <bmanish15597@gmail.com>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Acked-by: Dave Taht <dave.taht@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: aquantia: add hwmon support

This series adds HWMON support for the temperature sensor and the
related alarms on the 107/108/109 chips.

v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
  (avoids problems if PHY driver is built in and HWMON is a module)

v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-02-22

This series contains updates to the ice driver only.

Bruce adds the __always_unused attribute to a parameter to avoid
compiler warnings when using -Wunused-parameter.  Fixed unnecessary
type-casting and the use of sizeof().  Fix the allocation of structs
that have become memory hogs, so allocate them in heaps and fix all the
associated references.  Fixed the "possible" numeric overflow issues
that were caught with static analysis.

Maciej fixes the maximum MTU calculation by taking into account double
VLAN tagging amd ensure that the operations are done in the correct
order.

Victor fixes the supported node calculation, where we were not taking
into account if there is space to add the new VSI or intermediate node
above that layer, then it is not required to continue the calculation.
Added a check for a leaf node presence for a given VSI, which is needed
before removing a VSI.

Jake fixes an issue where the VSI list is shared, so simply removing a
VSI from the list will cause issues for the other users who reference
the list.  Since we also free the memory, this could lead to
segmentation faults.

Brett fixes an issue where driver unload could cause a system reboot
when intel_iommu=on parameter is set.  The issue is that we are not
clearing the CAUSE_ENA bit for the appropriate control queues register
when freeing the miscellaneous interrupt vector.

Mitch is so kind, he prevented spamming the VF with link messages when
the link status really has not changed.  Updates the driver to use the
absolute vector ID and not the per-PF vector ID for the VF MSIx vector
allocation.

Lukasz fixes the ethtool pause parameter for the ice driver, which was
originally based off the link status but is now based off the PHY
configuration.  This is to resolve an issue where pause parameters could
be set while link was down.

Jesse updates the string that reports statistics so the string does not
get modified at runtime and cause reports of string truncation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Function tc_dump_chain() obtains and releases block->lock on each iteration
of its inner loop that dumps all chains on block. Outputting chain template
info is fast operation so locking/unlocking mutex multiple times is an
overhead when lock is highly contested. Modify tc_dump_chain() to only
obtain block->lock once and dump all chains without releasing it.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using tcf_walker->stop flag to determine when tcf_walker->fn() was called
at least once is unreliable. Some classifiers set 'stop' flag on error
before calling walker callback, other classifiers used to call it with NULL
filter pointer when empty. In order to prevent further regressions, extend
tcf_walker structure with dedicated 'nonempty' flag. Set this flag in
tcf_walker->fn() implementation that is used to check if classifier has
filters configured.

Fixes: 8b64678e ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 787799a9 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.

This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).

This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.

Fixes: 787799a9 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per discussion with Daniel[1] and Eric[2], these SOCK_DEBUG() calles in
TCP are not needed now.
We'd better clean up it.

[1] https://patchwork.ozlabs.org/patch/1035573/
[2] https://patchwork.ozlabs.org/patch/1040533/Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

parameter state in the tcp_sacktag_bsearch() is not used.
So, it can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A test started warning on a string truncation. This led to an unfortunate
realization that we are likely not accounting for the stats length
correctly before this patch, so fix the issue by putting "port." in front
of all the PF stats, instead of magically prepending it at runtime.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool reported pause params based on the currently negotiated
link settings instead of current PHY config. User was not able
to turn off pause params because ethtool was incorrectly reporting
parameters as off when link was down even though PHY was configured
to support pause frames. Now pause params are taken from PHY config
instead of link status.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the PF driver sets up the VF MSI-X vector allocation, it needs to
use the hardware absolute vector ID, not the per-PF vector ID. Without
this change we see (apparent) TX hangs when using VFs on multiple PFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for a leaf node presence for a given VSI. This check is required
before removing a VSI since VSIs can't be removed with enabled queues
(with leaf nodes) from the FW scheduler tree unless its a reset.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the flush Tx pipe flag instead of getting an EAGAIN error when FW
times out in processing the disable Tx queue command.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On older devices like X710 and X722, the VF's ARQLEN register is cleared
on reset, so the VF driver uses that register to detect an unannounced
reset. Unfortunately, on devices controlled by ice, this register is NOT
cleared on reset. This causes the VF to miss resets, and even on
properly-announced resets, the VF driver complains that it didn't see
the reset.

To fix this, we'll do it in software. When we handle a VF reset (whether
triggered by software or VFLR), clear this register after the HW reset
is complete.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't send a link message to the VFs unless link actually changes state.
This avoids a small timing hole in some VF drivers that can cause an
apparent TX hang if they receive a link status message at the wrong time.

Although we have fixed the timing hole in the current VF driver, there
are still lots of drivers in the field that have this timing hole. Let's
not fall into it if we can avoid it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In ice_vsi_release we are always assigning a value to the local VF
variable. Change this to only be assigned if the VSI is a VF VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When compiling and analyzing the driver on newer kernels, a static
analyzer warns about the following "numeric overflow" issues:

  "The result of expression: 'budget-1' generates 4-byte type while casting
   to a bigger size of 8-byte".

  "The result of expression: '*words-words_read' generates 4-byte type
   while casting to a bigger size of 8-byte".

Fix them both.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the kernel has the intel_iommu=on parameter set, on some
platforms removing the driver causes a system reboot. In initialization
we associate the control queue interrupts with the pf->hw_oicr_idx and
enable the interrupts by setting the CAUSE_ENA bit. The problem comes
on teardown because we are not clearing the CAUSE_ENA bit for the
control queues, but the vector at pf->hw_oicr_idx (miscellaneous
interrupt vector) gets disabled.

Fix this by clearing the CAUSE_ENA bit in the appropriate control queue
registers on when freeing the miscellaneous interrupt vector. Also,
move the call to ice_free_irq_msix_misc() to after ice_deinit_sw() in
ice_remove() because ice_deinit_sw() makes an AQ call, but
ice_free_irq_msix_misc() disables the miscellaneous vector and it's
associated interrupts.

Also, create two small helper functions to enable and disable the
control queue interrupts respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When adding multiple VLANs to the same VSI, the ice_add_vlan code will
share the VSI list, so as not to create multiple unnecessary VSI lists.

Consider the following flow

  ice_add_vlan(hw, <VSI 0 VID 7, VSI 0 VID 8, VSI 0 VID 9>)

Where we add three VLAN filters for VIDs 7, 8, and 9, all for VSI 0.

The ice_add_vlan will create a single vsi_list and share it among all
the filters.

Later, if we try to remove a VLAN,

  ice_remove_vlan(hw, <VSI 0 VID 7>)

Then the removal code will update the vsi_list and remove VSI 0 from it.
But, since the vsi_list is shared, this breaks the list for the other
users who reference it. We actually even free the VSI list memory, and
may result in segmentation faults.

This is due to the way that VLAN rule share VSI lists with reference
counts, and is caused because we call ice_rem_update_vsi_list even when
the ref_cnt is greater than one.

To fix this, handle the case where ref_cnt is greater than one
separately. In this case, we need to remove the associated rule without
modifying the vsi_list, since it is currently being referenced by
another rule. Instead, we just need to decrement the VSI list ref_cnt.

The case for handling sharing of VSI lists with multiple VSIs is not
currently supported by this code. No such rules will be created today,
and this code will require changes if/when such code is added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

struct ice_vsi_ctx has gotten large enough that function local declarations
of it on the stack are causing stack hogs.  Fix that by allocating the
structs on heap.  Cleanup some formatting issues in the code around these
changes and fix incorrect data type uses of returned functions in a couple
places.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With sizeof(), it is preferable to use the variable of type <type> instead
of sizeof(<type>).

There are multiple places where a temporary variable is used to hold a
'size' value which is then used for a subsequent alloc/memset. Get rid
of the temporary variable by calculating size as part of the alloc/memset
statement.

Also remove unnecessary type-cast.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

VSI supported nodes are calculated in order to add the VSI parent or
intermediate nodes to the scheduler tree. If one of the node in below
layers (from VSI layer) has space to add the new VSI or intermediate node
above that layer then it's not required to continue the calculation further
for below layers.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently ICE_MAX_MTU subtracts only ETH_HLEN from max frame size and
adds ETH_FCS_LEN and VLAN_HLEN, which is not what was intended.
The ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN expression should be surrounded
with parentheses.

Wrap mentioned expression and take into account VLAN double tagging.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 87b0984e ("net: Add extack argument to ndo_fdb_add()") in
net-next added an extended parameter to the .ndo_fdb_add op and changed
ice_fdb_add() accordingly. Update the function header and add the
__always_unused attribute to the new parameter to avoid -Wunused-parameter
warnings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We have no more in tree users of switchdev_port_attr_get() after
d0e698d5 ("Merge branch 'net-Get-rid-of-switchdev_port_attr_get'")
so completely remove the function signature and body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().

Fixes: 5502b218 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR,
add this. Users will ignore speed and duplex settings in BMCR because
we're emulating auto-neg, therefore we can remove related code.
See also following discussion [0].

[0] https://marc.info/?t=155041784900002&r=1&w=2Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
Here's the main bluetooth-next pull request for the 5.1 kernel.

 - Fixes & improvements to mediatek, hci_qca, btrtl, and btmrvl HCI drivers
 - Fixes to parsing invalid L2CAP config option sizes
 - Locking fix to bt_accept_enqueue()
 - Add support for new Marvel sd8977 chipset
 - Various other smaller fixes & cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

dst_output() frees skb when it fails (see, for example,
ip_finish_output2), so it must not be freed in this case.

Fixes: 3bd0b152 ("bpf: add handling of BPF_LWT_REROUTE to lwt_bpf.c")
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip l add dev tun type gretap key 1000

Non-tunnel-dst ip tunnel device can send packet through lwtunnel
This patch provide the tun_inf dst cache support for this mode.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx: Avoid false positive Lockdep splats

When acquiring the GPIO interrupt line for the switch, it is possible
to trigger lockdep splats. These are false positives, the mutex is in
a different IRQ descriptor. But fix it anyway, since it could mask
real locking issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following false positive lockdep splat has been observed.

======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704

but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&desc->request_mutex){+.+.}:
       mutex_lock_nested+0x1c/0x24
       __setup_irq+0xa0/0x704
       request_threaded_irq+0xd0/0x150
       mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
       mdio_probe+0x2c/0x54
       really_probe+0x200/0x2c4
       driver_probe_device+0x5c/0x174
       __driver_attach+0xd8/0xdc
       bus_for_each_dev+0x58/0x7c
       bus_add_driver+0xe4/0x1f0
       driver_register+0x7c/0x110
       mdio_driver_register+0x24/0x58
       do_one_initcall+0x74/0x2e8
       do_init_module+0x60/0x1d0
       load_module+0x1968/0x1ff4
       sys_finit_module+0x8c/0x98
       ret_fast_syscall+0x0/0x28
       0xbedf2ae8

-> #0 (&chip->reg_lock){+.+.}:
       __mutex_lock+0x50/0x8b8
       mutex_lock_nested+0x1c/0x24
       __setup_irq+0x640/0x704
       request_threaded_irq+0xd0/0x150
       mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
       mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
       mdio_probe+0x2c/0x54
       really_probe+0x200/0x2c4
       driver_probe_device+0x5c/0x174
       __driver_attach+0xd8/0xdc
       bus_for_each_dev+0x58/0x7c
       bus_add_driver+0xe4/0x1f0
       driver_register+0x7c/0x110
       mdio_driver_register+0x24/0x58
       do_one_initcall+0x74/0x2e8
       do_init_module+0x60/0x1d0
       load_module+0x1968/0x1ff4
       sys_finit_module+0x8c/0x98
       ret_fast_syscall+0x0/0x28
       0xbedf2ae8

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&desc->request_mutex);
                               lock(&chip->reg_lock);
                               lock(&desc->request_mutex);
  lock(&chip->reg_lock);

&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.

Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lwtunnel_state is not init the dst_cache Which make the
ip_md_tunnel_xmit can't use the dst_cache. It will lookup
route table every packets.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch enables returning 'type' in msghdr for records that are
retrieved with MSG_PEEK in recvmsg. Further it prevents records peeked
from socket from getting clubbed with any other record of different
type when records are subsequently dequeued from strparser.

For each record, we now retain its type in sk_buff's control buffer
cb[]. Inside control buffer, record's full length and offset are already
stored by strparser in 'struct strp_msg'. We store record type after
'struct strp_msg' inside 'struct tls_msg'. For tls1.2, the type is
stored just after record dequeue. For tls1.3, the type is stored after
record has been decrypted.

Inside process_rx_list(), before processing a non-data record, we check
that we must be able to return back the record type to the user
application. If not, the decrypted records in tls context's rx_list is
left there without consuming any data.

Fixes: 692d7b5d ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>