- 13 Oct, 2021 3 commits
-
-
Dan Carpenter authored
The devm_kmemdup() function doesn't return error pointers, it returns NULL on error. Fixes: eb3a97a6 ("ath9k: fetch calibration data via nvmem subsystem") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211011123533.GA15188@kili
-
Baochen Qiang authored
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel included in scan channel list. Without it, firmware will not send a probe request frame which is needed in connection to an AP configured with hidden SSID/network_id. So fix this to allow probe request frames to be sent in cases where a beacon frame has been seen on the channel first. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
Baochen Qiang <bqiang@codeaurora.org> Signed-off-by:
-
Christian Lamparter authored
The common DT property can be used to limit the available channels but ath9k has to manually call wiphy_read_of_freq_limits(). I would have put this into ath9k_of_init(). But it didn't work there. The reason is that in ath9k_of_init() the channels and bands are not yet registered in the wiphy struct. So there isn't any channel to flag as disabled. Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
- 11 Oct, 2021 5 commits
-
-
Baochen Qiang authored
Some targets, QCA6390 for example, use only one TCL ring, it is better to initialize only one ring and leave others untouched for such targets. This is a theoretical fix found during code review, no visible impact. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by:
Jouni Malinen <jouni@codeaurora.org> Signed-off-by:
-
Baochen Qiang authored
When doing "rmmod ath11k_pci", ath11k performs global SOC reset and MHI reset, where 0 address access is captured by IOMMU. See log below: ... [ 133.953860] ath11k_pci 0000:02:00.0: setting mhi state: DEINIT(1) [ 133.959714] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020] [ 133.973854] ath11k_pci 0000:02:00.0: MHISTATUS 0xff04 [ 133.974095] ath11k_pci 0000:02:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000a address=0x0 flags=0x0020] ... This issue is also observed in SSR process, cause a similar sequence as above is performed. Such an invalid access occurs because, during rmmod or SSR, MSI address is cleared but HW MSI functionality not disabled, thus HW target is able to raise an MSI transaction with 0 as MSI address. So it can be fixed by simply disabling MSI before reset. For SSR, since MSI functionality is still needed after target is brought back, we need to reenable it. Also change naming of some interfaces related. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Tuo Li authored
kzalloc() is used to allocate memory for cd->detectors, and if it fails, channel_detector_exit() behind the label fail will be called: channel_detector_exit(dpd, cd); In channel_detector_exit(), cd->detectors is dereferenced through: struct pri_detector *de = cd->detectors[i]; To fix this possible null-pointer dereference, check cd->detectors before the for loop to dereference cd->detectors. Reported-by:
TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by:
Tuo Li <islituo@gmail.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Use 2-factor multiplication argument form kcalloc() instead of kzalloc(). Link: https://github.com/KSPP/linux/issues/162Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
-
Colin Ian King authored
Variable fw_size is being assigned a value that is never read and being re-assigned a new value in the next statement. The assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Fixes: 336e7b53 ("ath11k: clean up BDF download functions") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
- 07 Oct, 2021 1 commit
-
-
Colin Ian King authored
There is a spelling mistake in an ath11k_warn message. Fix it. Signed-off-by:
-
- 05 Oct, 2021 11 commits
-
-
Tim Gardner authored
Coverity complains that a constant variable guards dead code. In fact, mpdu_buf is set NULL and never updated. 4834err_merge_fail: null: At condition mpdu_buf, the value of mpdu_buf must be NULL. dead_error_condition: The condition mpdu_buf cannot be true. CID 92162 (#1 of 1): 'Constant' variable guards dead code (DEADCODE) dead_error_line: Execution cannot reach the expression decap_format != DP_RX_DECAP_TYPE_RAW inside this statement: if (mpdu_buf && decap_forma.... Local variable mpdu_buf is assigned only once, to a constant value, making it effectively constant throughout its scope. If this is not the intent, examine the logic to see if there is a missing assignment that would make mpdu_buf not remain constant. 4835 if (mpdu_buf && decap_format != DP_RX_DECAP_TYPE_RAW) { Fix this by removing mpdu_buf and unreachable code. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: ath11k@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
-
Christian Lamparter authored
This replaces the existing .txt binding file. Furthermore, this also helps with validating DTS files. Introduced binding changes: 1. added inherited mac-address nvmem property 2. added inherited ieee80211-freq-limit property 3. added new calibration nvmem property 4. added second example (taken from the Netgear WNDR3700v2) Reason: Setting qca,no-eeprom; takes presedence over nvmem-cells. I think a different example is needed, because the driver can only reads from one calibration source per device. 5. (re-added) chip list (based on data from ath9k's pci.c) Added binding .yaml to MAINTAINERS. Reviewed-by:Rob Herring <robh@kernel.org> Signed-off-by:
-
Linus Lüssing authored
In tests with two Lima boards from 8devices (QCA4531 based) on OpenWrt 19.07 we could force a silent restart of a device with no serial output when we were sending a high amount of UDP traffic (iperf3 at 80 MBit/s in both directions from external hosts, saturating the wifi and causing a load of about 4.5 to 6) and were then triggering an ath9k_queue_reset(). Further debugging showed that the restart was caused by the ath79 watchdog. With disabled watchdog we could observe that the device was constantly going into ath_isr() interrupt handler and was returning early after the ATH_OP_HW_RESET flag test, without clearing any interrupts. Even though ath9k_queue_reset() calls ath9k_hw_kill_interrupts(). With JTAG we could observe the following race condition: 1) ath9k_queue_reset() ... -> ath9k_hw_kill_interrupts() -> set_bit(ATH_OP_HW_RESET, &common->op_flags); ... <- returns 2) ath9k_tasklet() ... -> ath9k_hw_resume_interrupts() ... <- returns 3) loops around: ... handle_int() -> ath_isr() ... -> if (test_bit(ATH_OP_HW_RESET, &common->op_flags)) return IRQ_HANDLED; x) ath_reset_internal(): => never reached <= And in ath_isr() we would typically see the following interrupts / interrupt causes: * status: 0x00111030 or 0x00110030 * async_cause: 2 (AR_INTR_MAC_IPQ) * sync_cause: 0 So the ath9k_tasklet() reenables the ath9k interrupts through ath9k_hw_resume_interrupts() which ath9k_queue_reset() had just disabled. And ath_isr() then keeps firing because it returns IRQ_HANDLED without actually clearing the interrupt. To fix this IRQ storm also clear/disable the interrupts again when we are in reset state. Cc: Sven Eckelmann <sven@narfation.org> Cc: Simon Wunderlich <sw@simonwunderlich.de> Cc: Linus Lüssing <linus.luessing@c0d3.blue> Fixes: 872b5d81 ("ath9k: do not access hardware on IRQs during reset") Signed-off-by:Linus Lüssing <ll@simonwunderlich.de> Signed-off-by:
-
Linus Lüssing authored
Sometimes, in yet unknown cases the wifi chip stops working. To allow a watchdog in userspace to easily and quickly reset the wifi chip, add the according functionality to userspace. A reset can then be triggered via: $ echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/reset The number of user resets can further be tracked in the row "User reset" in the same file. So far people usually used "iw scan" to fix ath9k chip hangs from userspace. Which triggers the ath9k_queue_reset(), too. The reset file however has the advantage of less overhead, which makes debugging bugs within ath9k_queue_reset() easier. Signed-off-by:
-
Stephen Boyd authored
When rebooting on sc7180 Trogdor devices I see the following crash from the wifi driver. ath10k_snoc 18800000.wifi: firmware crashed! (guid 83493570-29a2-4e98-a83e-70048c47669c) This is because a modem stop event looks just like a firmware crash to the driver, the qmi connection is closed in both cases. Use the qcom ssr notifier block to stop treating the qmi connection close event as a firmware crash signal when the modem hasn't actually crashed. See ath10k_qmi_event_server_exit() for more details. This silences the crash message seen during every reboot. Fixes: 3f14b73c ("ath10k: Enable MSA region dump support for WCN3990") Cc: Youghandhar Chintala <youghand@codeaurora.org> Cc: Abhishek Kumar <kuabhs@chromium.org> Cc: Steev Klimaszewski <steev@kali.org> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by:
Stephen Boyd <swboyd@chromium.org> Reviewed-by:
Rakesh Pillai <pillair@codeaurora.org> Tested-By:
Youghandhar Chintala <youghand@codeaurora.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.16. Major changes: ath9k * load calibration data and pci init values via nvmem subsystem ath11k * include channel rx and tx time in survey dump statistics * support for setting fixed Wi-Fi 6 rates from user space * support for 80P80 and 160 MHz bandwidths * spectral scan support for QCN9074 * support for calibration data files per radio * support for calibration data via eeprom * support for rx decapsulation offload (data frames in 802.3 format) * support channel 2 in 6 GHz band ath10k * include frame time stamp in beacon and probe response frames wcn36xx * enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
-
Chris Chiu authored
According to the Realtek propritary driver and the rtw88 driver, the tx rates of the ack (includes block ack) are initialized with lower tx rates (no HT rates) which is set by the RRSR register value. In real cases, ack rate higher than current tx rate could lead to difficulty for the receiving end to receive management/control frames. The retransmission rate would be higher then expected when the driver is acting as receiver and the RSSI is not good. Cross out higer rates for ack packet before implementing dynamic rrsr configuration like the commit 48308726 ("rtw88: add dynamic rrsr configuration"). Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Acked-by:
Jes Sorensen <Jes.Sorensen@gmail.com> Signed-off-by:
-
Sohaib Mohamed authored
Do not initialise statics to 0 ERROR found by checkpatch.pl Signed-off-by:
Sohaib Mohamed <sohaib.amhmd@gmail.com> Signed-off-by:
-
Hans de Goede authored
The Cyberbook T116 tablet contains quite generic names in the sys_vendor and product_name DMI strings, without this patch brcmfmac will try to load: "brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which is way too generic. The nvram file shipped on the factory Android image contains the exact same settings as those used on the AcePC T8 mini PC, so point the new DMI nvram filename quirk to the acepc-t8 nvram file. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Zong-Zhe Yang authored
The usage of fw_crash debugfs is to write 1 to it to trigger fw crash simulation and to read from it to check the state. When zero is read, it is supposed to mean fw crash/restart process is done. Then, some test plans can be designed for crash/restart. e.g. step 1. trigger fw crash simulation step 2. poll the state until zero is read step 3. check connection by ping test However, in certain connection cases, triggering fw crash simulation will take a while. If the state is queried too early before restart begins processing, it may mistakenly think restart process has been done. If some tests are started at this time, something unexpected might happen due to the follow-up restart process. To avoid that, let fw_crash also show non-zero when a simulation is still triggering. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Zong-Zhe Yang authored
When fw fifo dumps, RX clock gating should be disabled to avoid something unexpected. However, the register operation ran into a mistake. So, we fix it. Signed-off-by:
-
- 28 Sep, 2021 20 commits
-
-
Fabio Estevam authored
On a i.MX-based board with a QCA9377 Wifi chip, the following errors are seen after launching the 'hostapd' application: hostapd /etc/wifi.conf Configuration file: /etc/wifi.conf wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! Using interface wlan0 with hwaddr 00:1f:7b:31:04:a0 and ssid "thessid" IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: interface state COUNTRY_UPDATE->ENABLED wlan0: AP-ENABLED NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! ... Fix this problem by adding the BH locking around napi-schedule(), in the same way it was done in commit e63052a5 ("mlx5e: add add missing BH locking around napi_schdule()"). Its commit log provides the following explanation: "It's not correct to call napi_schedule() in pure process context. Because we use __raise_softirq_irqoff() we require callers to be in a context which will eventually lead to softirq handling (hardirq, bh disabled, etc.). With code as is users will see: NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!! " Fixes: cfee8793 ("ath10k: enable napi on RX path for sdio") Signed-off-by:
Fabio Estevam <festevam@denx.de> Signed-off-by:
-
Loic Poulain authored
When receiving a beacon or probe response, we should update the boottime_ns field which is the timestamp the frame was received at. (cf mac80211.h) This fixes a scanning issue with Android since it relies on this timestamp to determine when the AP has been seen for the last time (via the nl80211 BSS_LAST_SEEN_BOOTTIME parameter). Fixes: 5e3dd157 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices") Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Alagu Sankar authored
Beacon buffer for high latency devices does not use DMA. other similar buffer allocation methods in the driver have already been modified for high latency path. Fix the beacon buffer allocation left out in the earlier high latency changes. Signed-off-by:
Alagu Sankar <alagusankar@silex-india.com> Signed-off-by:
Erik Stromdahl <erik.stromdahl@gmail.com> [fabio: adapt it to use ar->bus_param.dev_type ] Signed-off-by:
-
Baochen Qiang authored
For fragmented packets, ath11k reassembles each fragment as a normal packet and then reinjects it into HW ring. In this case, the DMA direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise invalid payload will be reinjected to HW and then delivered to host. What is more, since arbitrary memory could be allocated to the frame, we don't know what kind of data is contained in the buffer reinjected. Thus, as a bad result, private info may be leaked. Note that this issue is only found on Intel platform. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Parse SMPS configuration from IEs and configure. Without this, SMPS is not enabled for 6 GHz band. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Currently A-MPDU aggregation parameters are not being configured during peer association for 6 GHz band. Hence, extract these parameters from station's capabilities received in association request and send to firmware. Without this, A-MPDU aggregation is not happening in 6 GHz band. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Pradeep Kumar Chitrapu authored
Add IEEE80211_HE_6GHZ_MAX_AMPDU_FACTOR as per IEEE Std 802.11ax-2021, 9.4.2.263 to use for peer max A-MPDU factor in 6 GHz band. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Wen Gong authored
Scan failure can not be recovered from when running a loop of the following steps: 1. run scan: "iw wlan scan". 2. run command: echo assert > /sys/kernel/debug/ath11k/qca6490\ hw2.0/simulate_fw_crash immediately after step 1. result: scan failed and can not recover even when wlan recovery succeeds: command failed: Device or resource busy (-16) reason: When scan arrives, WMI_START_SCAN_CMDID is sent to the firmware and function ath11k_mac_op_hw_scan() returns, then simulate_fw_crash arrives and the scan started event does not arrive, and then it starts to do recovery of wlan. __ath11k_mac_scan_finish() which is called from ath11k_core_halt() is one step of recovery, it will not call ieee80211_scan_completed() by logic currently because the scan state is ATH11K_SCAN_STARTING. Thus it leads the scan not being completed in mac80211, and leads all consecutive scans failing with -EBUSY in nl80211_trigger_scan even after wlan recovery success. Indicate scan complete with aborted flag to mac80211 for ATH11K_SCAN_STARTING to allow recovery from scan failed with "Device or resource busy (-16)" after wlan recovery. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Wen Gong authored
ath11k prints "Received scan event for unknown vdev" when doing the following test: 1. trigger scan 2. wait 0.2 second 3. iw reg set or 11d scan complete from firmware Reason: When iw reg set or 11d scan complete, the new country code will be set to the firmware, and the new regdomain info indicated to ath11k, then the new channel list will be sent to the firmware. The firmware will cancel the current scan after receiving WMI_SCAN_CHAN_LIST_CMDID which is used for the new channel list, and the state of ath11k is ATH11K_SCAN_RUNNING, then ath11k_get_ar_on_scan_abort() returns NULL and ath11k_scan_event() returns at this point and does not indicate scan completion to mac80211. Indicate scan completion to mac80211 and get rid of the "Received scan event for unknown vdev" print for the above case. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Wen Gong authored
When wlan interface is up, 11d scan is sent to the firmware, and the firmware needs to spend couple of seconds to complete the 11d scan. If immediately a normal scan from user space arrives to ath11k, then the normal scan request is also sent to the firmware, but the scan started event will be reported to ath11k until the 11d scan complete. When timed out for the scan started in ath11k, ath11k stops the normal scan and the firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan. ath11k has no handler for the event and then timed out for the scan completed in ath11k_scan_stop(), and ath11k prints the following error message. [ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out [ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110 [ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110 Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to get rid of the above error message. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Venkateswara Naralasetty authored
Add HTT stats support for, 29-ATH11K_DBG_HTT_EXT_STATS_PEER_CTRL_PATH_TXRX_STATS: Used to dump the control path txrx stats for each connected peer. Usage: echo 29 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type cat /sys/kernel/debug/ieee80211/phyx/netdev\:wlan0/stations/ <sta mac>/htt_peer_stats. 31-ATH11K_DBG_HTT_EXT_STATS_PDEV_TX_RATE_TXBF_STATS: Used to dump the per pdev tx rate txbf stats. Usage: echo 31 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats 32-ATH11k_DBG_HTT_EXT_STATS_TXBF_OFDMA: Used to dump the TXBF ofdma stats for all ofdma users. Usage: echo 32 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats 37-ATH11K_DBG_HTT_EXT_PHY_COUNTERS_AND_PHY_STATS: Used to dump the mac and phy txrx counts and phy stats like per chain rssi and ANI level. Usage: echo 37 > /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats_type cat /sys/kernel/debug/ieee80211/phyx/ath11k/htt_stats Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00486-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Venkateswara Naralasetty <vnaralas@codeaurora.org> Signed-off-by:
-
Seevalamuthu Mariappan authored
In debugfs_htt_stats.c, masking and shifting is done to get stats values. Instead use GENMASK and FIELD_GET to improve code readability and maintenance. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Seevalamuthu Mariappan <seevalam@codeaurora.org> Signed-off-by:
-
Seevalamuthu Mariappan authored
To support the HTT Stats DebugFS interface a single large buffer that contains the stats must be provided to the DebugFS infrastructure. In the current code, for each class of stats, the stats are first formatted in a local on-stack buffer, and then the local buffer is copied to the large DebugFS buffer. This logic has a problem when, for a given class, the formatted stats exceed the size of the on-stack buffer. When this occurs the stats for this class is truncated. In addition, this logic is inefficient since it introduces an unnecessary memory copy. To address these issues, update the logic to no longer use a local on-stack buffer, and instead write the formatted data directly into the large DebugFS buffer. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Seevalamuthu Mariappan authored
Get rid of macro HTT_DBG_OUT and replace it with scnprintf(). The macro does not do anything else. Added required new line characters to scnprintf() for proper display. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01105-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Seevalamuthu Mariappan authored
Renaming of macro is done to describe the macro functionality better as the macro functionality is modified in next patch-sets. No functional changes are done. Signed-off-by:
-
Baochen Qiang authored
The buffer pointed to by event is not freed in case ATH11K_FLAG_UNREGISTERING bit is set, resulting in memory leak, so fix it. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by:
-
Baochen Qiang authored
Current code clears debug registers after SOC global reset performed in ath11k_pci_sw_reset. However at that time those registers are not accessible due to reset, thus they are actually not cleared at all. For WCN6855, it may cause target fail to initialize. This issue can be fixed by moving clear action ahead. In addition, on some specific platforms, need to add delay to wait those registers to become accessible. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Baochen Qiang authored
There are MSDUs whose length are invalid. For example, attackers may inject on purpose truncated A-MSDUs with invalid MSDU length. Such MSDUs are marked with an err bit set in rx attention tlvs, so we can check and drop them. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Wen Gong authored
WCN6855 has 2 phys, one is 2G, another is 5G/6G, so it should copy the cap info of 6G band under the check of WMI_HOST_WLAN_5G_CAP as well as for the 5G band. Some chips like QCN9074 only have 6G, not have 2G and 5G, and this 6G capability is also under WMI_HOST_WLAN_5G_CAP, so this change will not disturb it. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Wen Gong authored
For some chips such as WCN6855, single_pdev_only is set in struct ath11k_hw_params which means ath11k calls ieee80211_register_hw() only once and create only one device interface, and that device interface supports all 2G/5G/6G channels. ath11k_mac_setup_channels_rates() sets up the channels and it is called for each device interface. It is called only once for single_pdev_only, and then set up all channels for 2G/5G/6G. The logic of ath11k_mac_setup_channels_rates() is not suitable for single_pdev_only, it leads to all 6G channels being disabled for the device interface which is single_pdev_only such as WCN6855. Add channel frequency checks for the 6G band and enable the 6G channels properly based on what is supported by the chip. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
