Skip to content

L
linux
Switch branch/tag
  1. 29 Oct, 2007 5 commits
    • Jeff Garzik's avatar
      [libata] Address some checkpatch-spotted issues · 5796d1c4
      Jeff Garzik authored 
      Signed-off-by: default avatarJeff Garzik <jgarzik@redhat.com>
      5796d1c4
    • Jeff Garzik's avatar
      [libata] fix 'if(' and similar areas that lack whitespace · b447916e
      Jeff Garzik authored 
      Signed-off-by: default avatarJeff Garzik <jgarzik@redhat.com>
      b447916e
    • Tejun Heo's avatar
      libata: implement ata_wait_after_reset() · 88ff6eaf
      Tejun Heo authored 
      On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait.  As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.

This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.

Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      88ff6eaf
    • Tejun Heo's avatar
      libata: track SLEEP state and issue SRST to wake it up · 054a5fba
      Tejun Heo authored 
      ATA devices in SLEEP mode don't respond to any commands.  SRST is
necessary to wake it up.  Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.

This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      054a5fba
    • Tejun Heo's avatar
      libata: relocate and fix post-command processing · 4dbfa39b
      Tejun Heo authored 
      Some commands need post-processing after successful completion.  This
was done in ata_scsi_qc_complete() till now but this has the following
problems.

* Post-command processing gets executed when qc is completed from EH.
  Some qc's are retried from EH with zero err_mask and thus triggers
  unnecessary/incorrect post-command processing.

* Command post processing doesn't belong to SAT layer.

* Link-wide revalidation was scheduled where device revalidation
  suffices.

This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used.  While at it,
restructure code a bit for readability.
Signed-off-by: default avatarTejun Heo <htejun@gmail.com>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
      4dbfa39b
  3. 28 Oct, 2007 8 commits
  5. 27 Oct, 2007 27 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7