Pranavi Somisetty says:

====================
Add support for partial store and forward

Add support for partial store and forward mode in Cadence MACB.

Link for v1:
https://lore.kernel.org/all/20221213121245.13981-1-pranavi.somisetty@amd.com/

Changes v2:
1. Removed all the changes related to validating FCS when Rx checksum
offload is disabled.
2. Instead of using a platform dependent number (0xFFF) for the reset
value of rx watermark, derive it from designcfg_debug2 register.
3. Added a check to see if partial s/f is supported, by reading the
designcfg_debug6 register.
4. Added devicetree bindings for "rx-watermark" property.
Link for v2:
https://lore.kernel.org/all/20230511071214.18611-1-pranavi.somisetty@amd.com/

Changes v3:
1. Fixed DT schema error: "scalar properties shouldn't have array keywords"
2. Modified description of rx-watermark in to include units of the watermark value
3. Modified the DT property name corresponding to rx_watermark in pbuf_rxcutthru to
"cdns,rx-watermark".
4. Followed reverse christmas tree pattern in declaring variables.
5. Return -EINVAL when an invalid watermark value is set.
6. Removed netdev_info when partial store and forward is not enabled.
7. Validating the rx-watermark value in probe itself and only write to the register
in init.
8. Writing a reset value to the pbuf_cuthru register before disabing partial store
and forward is redundant. So removing it.
9. Removed the platform caps flag.
10. Instead of reading rx-watermark from DT in macb_configure_caps,
reading it in probe.
11. Changed Signed-Off-By and author names on the macb driver patch.
Link for v3:
https://lore.kernel.org/all/20230530095138.1302-1-pranavi.somisetty@amd.com/

Changes v4:
1. Modified description for "rx-watermark" property in the DT bindings.
2. Changed the width of the rx-watermark property to uint32.
3. Removed redundant code and unused variables.
4. When the rx-watermark value is invalid, instead of returning EINVAL,
do not enable partial store and forward.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the receive partial store and forward mode is activated, the
receiver will only begin to forward the packet to the external AHB
or AXI slave when enough packet data is stored in the packet buffer.
The amount of packet data required to activate the forwarding process
is programmable via watermark registers which are located at the same
address as the partial store and forward enable bits. Adding support to
read this rx-watermark value from device-tree, to program the watermark
registers and enable partial store and forwarding.
Signed-off-by: Maulik Jodhani <maulik.jodhani@xilinx.com>
Signed-off-by: Pranavi Somisetty <pranavi.somisetty@amd.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

watermark value is the minimum amount of packet data
required to activate the forwarding process. The watermark
implementation and maximum size is dependent on the device
where Cadence MACB/GEM is used.
Signed-off-by: Pranavi Somisetty <pranavi.somisetty@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: create device lookup API with reference tracking

We still see dev_hold() / dev_put() calls without reference tracker
getting added in new code. dev_get_by_name() / dev_get_by_index()
seem to be one of the sources of those. Provide appropriate helpers.
Allocating the tracker can obviously be done with an additional call
to netdev_tracker_alloc(), but a single API feels cleaner.

v2:
 - fix a dev_put() in ethtool
v1: https://lore.kernel.org/all/20230609183207.1466075-1-kuba@kernel.org/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5fa5ae60 ("netpoll: add net device refcount tracker to struct netpoll")
was part of one of the initial netdev tracker introduction patches.
It added an explicit netdev_tracker_alloc() for netpoll, presumably
because the flow of the function is somewhat odd.
After most of the core networking stack was converted to use
the tracking hold() variants, netpoll's call to old dev_hold()
stands out a bit.

np is allocated by the caller and ready to use, we can use
netdev_hold() here, even tho np->ndev will only be set to
ndev inside __netpoll_setup().
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

New users of dev_get_by_index() and dev_get_by_name() keep
getting added and it would be nice to steer them towards
the APIs with reference tracking.

Add variants of those calls which allocate the reference
tracker and use them in a couple of places.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves validate_linkmsg() out of do_setlink() to its callers
and deletes the early validate_linkmsg() call in __rtnl_newlink(), so
that it will not call validate_linkmsg() twice in either of the paths:

  - __rtnl_newlink() -> do_setlink()
  - __rtnl_newlink() -> rtnl_newlink_create() -> rtnl_create_link()

Additionally, as validate_linkmsg() is now only called with a real
dev, we can remove the NULL check for dev in validate_linkmsg().

Note that we moved validate_linkmsg() check to the places where it has
not done any changes to the dev, as Jakub suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/cf2ef061e08251faf9e8be25ff0d61150c030475.1686585334.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This filter already exists for excluding IPv6 SNMP stats. Extend its
definition to also exclude IFLA_VF_INFO stats in RTM_GETLINK.

This patch constitutes a partial fix for a netlink attribute nesting
overflow bug in IFLA_VFINFO_LIST. By excluding the stats when the
requester doesn't need them, the truncation of the VF list is avoided.

While it was technically only the stats added in commit c5a9f6f0
("net/core: Add drop counters to VF statistics") breaking the camel's
back, the appreciable size of the stats data should never have been
included without due consideration for the maximum number of VFs
supported by PCI.

Fixes: 3b766cd8 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: c5a9f6f0 ("net/core: Add drop counters to VF statistics")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Cc: Edwin Peer <espeer@gmail.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20230611105108.122586-1-gal@nvidia.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Petr Machata says:

====================
mlxsw: Preparations for out-of-order-operations patches

The mlxsw driver currently makes the assumption that the user applies
configuration in a bottom-up manner. Thus netdevices need to be added to
the bridge before IP addresses are configured on that bridge or SVI added
on top of it. Enslaving a netdevice to another netdevice that already has
uppers is in fact forbidden by mlxsw for this reason. Despite this safety,
it is rather easy to get into situations where the offloaded configuration
is just plain wrong.

As an example, take a front panel port, configure an IP address: it gets a
RIF. Now enslave the port to a bridge, and the RIF is gone. Remove the
port from the bridge again, but the RIF never comes back. There is a number
of similar situations, where changing the configuration there and back
utterly breaks the offload.

Over the course of the following several patchsets, mlxsw code is going to
be adjusted to diminish the space of wrongly offloaded configurations.
Ideally the offload state will reflect the actual state, regardless of the
sequence of operation used to construct that state.

No functional changes are intended in this patchset yet. Rather the patches
prepare the codebase for easier introduction of functional changes in later
patchsets.

- In patch #1, extract a helper to join a RIF of a given port, if there is
  one. In patch #2, use it in a newly-added helper to join a LAG interface.

- In patches #3, #4 and #5, add helpers that abstract away the rif->dev
  access. This will make it simpler in the future to change the way the
  deduction is done. In patch #6, do this for deduction from nexthop group
  info to RIF.

- In patch #7, add a helper to destroy a RIF. So far RIF was destroyed
  simply by kfree'ing it.

- In patch #8, add a helper to check if any IP addresses are configured on
  a netdevice. This helper will be useful later.

- In patch #9, add a helper to migrate a RIF. This will be a convenient
  place to put extensions later on.

- Patch #10 move IPIP initialization up to make ipip_ops_arr available
  earlier.
====================

Link: https://lore.kernel.org/r/cover.1686581444.git.petrm@nvidia.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

mlxsw will need to keep track of certain devices that are not related to
any of its front panel ports. This includes IPIP netdevices. To be able to
query the list of supported IPIP types, router->ipip_ops_arr needs to be
initialized.

To that end, move the IPIP initialization up (and finalization
correspondingly down).
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

RIF configuration contains a number of parameters that cannot be changed
after the RIF is created. For the IPIP loopbacks, this is currently worked
around by creating a new RIF with the desired configuration changes
applied, and updating next hops to the new RIF, and then destroying the old
RIF. This operation will be useful as a reusable atom, so extract a helper
to that effect.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This function will be useful later as the driver will need to retroactively
create RIFs for new uppers with addresses.

Add another helper that assumes RCU lock, and restructure the code to
skip the IPv6 branch not through conditioning on the addr_list_empty
variable, but by directly returning the result value. This makes the skip
more obvious than it previously was.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Right now freeing the object that mlxsw uses to keep track of a RIF is as
simple as calling a kfree. But later on as CRIF abstraction is brought in,
it will involve severing the link between CRIF and its RIF as well. Better
to have the logic encapsulated in a helper.

Since a helper is being introduced, make it a full-fledged destructor and
have it validate that the objects tracked at the RIF have been released.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

To abstract away deduction of RIF from the corresponding next hop group
info (NHGI), mlxsw currently uses a macro. In its current form, that macro
is impossible to extend to more general computation. Therefore introduce a
helper, mlxsw_sp_nhgi_rif(), and use it throughout. This will make it
possible to change the deduction path easily later on.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In order to abstract away deduction of netdevice from the corresponding
next hop, introduce a helper, mlxsw_sp_nexthop_dev(), and use it
throughout. This will make it possible to change the deduction path easily
later on.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The previous patch added a helper to access a netdevice given a RIF. Using
this helper in mlxsw_sp_rif_create() is unreasonable: the netdevice was
given in RIF creation parameters. Just take it there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In order to abstract away deduction of netdevice from the corresponding
RIF, introduce a helper, mlxsw_sp_rif_dev(), and use it throughout. This
will make it possible to change the deduction path easily later on.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Currently, joining a LAG very simply means that the LAG RIF should be
joined by the subport representing untagged traffic. If the RIF does not
exist, it does not have to be created: if the user wants there to be RIF
for the LAG device, they are supposed to add an IP address, and they are
supposed to do it after tha LAG becomes mlxsw upper.

We can also assume that the LAG has no uppers, otherwise the enslavement is
not allowed.

In the future, these ordering dependencies should be removed. That means
that joining LAG will be more complex operation, possibly involving a lazy
RIF creation, and possibly joining / lazily creating RIFs for VLAN uppers
of the LAG. It will be handy to have a dedicated function that handles all
this. The new function mlxsw_sp_router_port_join_lag() is that.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Split out of mlxsw_sp_port_vlan_router_join() the part that checks for RIF
and dispatches to __mlxsw_sp_port_vlan_router_join(), leaving it as wrapper
that just manages the router lock.

The new function, mlxsw_sp_port_vlan_router_join_existing(), will be useful
as an atom in later patches.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

sopass won't be set if wolopt doesn't change. This means the following
will fail to set the correct sopass.
ethtool -s eth0 wol s sopass 11:22:33:44:55:66
ethtool -s eth0 wol s sopass 22:44:55:66:77:88

Make sure we call into the driver layer set_wol if sopass is different.

Fixes: 55b24334 ("ethtool: ioctl: improve error checking for set_wol")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/1686605822-34544-1-git-send-email-justin.chen@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After commit b8a1a4cd ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f4 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230612071641.836976-1-u.kleine-koenig@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tools: ynl-gen: improvements for DPLL

A set of improvements needed to generate the kernel code for DPLL.
====================

Link: https://lore.kernel.org/r/20230612155920.1787579-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of reimplementing policies in MutliAttr for every
underlying type forward the calls to the base type.
This will be needed for DPLL which uses a multi-attr nest,
and currently gets an invalid NLA_NEST policy generated.
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Scalar range validation assumes enums start at 0.
Teach it to properly calculate the value range.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

MAC version 21H supports the 10Mbps speed. So, extend support to
platforms that support it.
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Naveen Mamindlapalli says:

====================
RVU NIX AF driver updates

This patch series includes a few enhancements and other updates to the
RVU NIX AF driver.

The first patch adds devlink option to configure NPC MCAM high priority
zone entries reservation. This is useful when the requester needs more
high priority entries than default reserved entries.

The second patch adds support for RSS hash computation using L3 SRC or
DST only, or L4 SRC or DST only.

The third patch updates DWRR MTU configuration for CN10KB silicon. HW uses
the DWRR MTU to compute DWRR weight.

Patch 4 configures the LBK link in TL3_TL2 configuration only when switch
mode is enabled.

Patch 5 adds an option in the mailbox request to enable/disable DROP_RE bit
which drops packets with L2 errors when set.

Patch 6 updates SMQ flush mechanism to stop other child nodes from
enqueuing any packets while SMQ flush is active. Otherwise SMQ flush may
timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When multiple transmit scheduler queues feed a TL1 transmit link, the
SMQ flush initiated on a low priority queue might get stuck when a high
priority queue fully subscribes the transmit link. This inturn effects
interface teardown. To avoid this, temporarily XOFF all TL1's other
immediate child transmit scheduler queues and also clear any rate limit
configuration on all the scheduler queues in SMQ(flush) hierarchy.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add option to toggle DROP_RE bit in rx cfg mbox. This helps in
modifying the config runtime as opposed to setting available via
nix_lf_alloc() mbox at NIX LF init time.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob Kollanukkaran <jerinj@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, all the TL3_TL2 nodes are being configured to enable
switch LBK channel 63 in them. Instead enable them only when switch
mode is enabled.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DWRR MTU config added for SDP and RPM/LBK links on CN10K
silicon is further extended on CK10KB silicon variant and made
it configurable. Now there are 4 DWRR MTU config to choose while
setting transmit scheduler's RR_WEIGHT.

Here we are reserving one config for each of RPM, SDP and LBK.
NIXX_AF_DWRR_MTUX(0) ---> RPM
NIXX_AF_DWRR_MTUX(1) ---> SDP
NIXX_AF_DWRR_MTUX(2) ---> LBK

PF/VF drivers can choose the DWRR_MTU to be used by setting
SMQX_CFG[pkt_link_type] to one of above. TLx_SCHEDULE[RR_WEIGHT]
is to be as configured 'quantum / 2^DWRR_MTUX[MTU]'. DWRR_MTU
of each link is exposed to PF/VF drivers via mailbox for
RR_WEIGHT calculation.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to select L3 SRC or DST only, L4 SRC or DST only for RSS
calculation.

AF consumer may have requirement as we can select only SRC or DST data for
RSS calculation in L3, L4 layers. With this requirement there will be
following combinations, IPV[4,6]_SRC_ONLY, IPV[4,6]_DST_ONLY,
[TCP,UDP,SCTP]_SRC_ONLY, [TCP,UDP,SCTP]_DST_ONLY. So, instead of creating
a bit for each combination, we are using upper 4 bits (31:28) in the
flow_key_cfg to represent the SRC, DST selection. 31 => L3_SRC,
30 => L3_DST, 29 => L4_SRC, 28 => L4_DST. These won't be part of flow_cfg,
so that we don't need to change the existing ABI.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NPC MCAM entries are currently divided into three priority zones
in AF driver: high, mid, and low. The high priority zone and low priority
zone take up 1/8th (each) of the available MCAM entries, and remaining
going to the mid priority zone.

The current allocation scheme may not meet certain requirements, such
as when a requester needs more high priority zone entries than are
reserved. This patch adds a devlink configurable option to increase the
number of high priority zone entries that can be allocated by requester.
The max number of entries that can be reserved for high priority usage
is 100% of available MCAM entries.

Usage:
1) Change high priority zone percentage to 75%:
devlink -p dev param set pci/0002:01:00.0 name npc_mcam_high_zone_percent \
value 75 cmode runtime

2) Read high priority zone percentage:
devlink -p dev param show pci/0002:01:00.0 name npc_mcam_high_zone_percent

The devlink set configuration is only permitted when no MCAM entries
are assigned, i.e., all MCAM entries are free, indicating that no PF/VF
driver is loaded. So user must unload/unbind PF/VF driver/devices before
modifying the high priority zone percentage.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test currently specifies "l2_miss" as "true" / "false", but the
version that eventually landed in iproute2 uses "1" / "0" [1]. Align the
test accordingly.

[1] https://lore.kernel.org/netdev/20230607153550.3829340-1-idosch@nvidia.com/

Fixes: 8c33266a ("selftests: forwarding: Add layer 2 miss test cases")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
splice, net: Some miscellaneous MSG_SPLICE_PAGES changes

Now that the splice_to_socket() has been rewritten so that nothing now uses
the ->sendpage() file op[1], some further changes can be made, so here are
some miscellaneous changes that can now be done.

 (1) Remove the ->sendpage() file op.

 (2) Remove hash_sendpage*() from AF_ALG.

 (3) Make sunrpc send multiple pages in single sendmsg() call rather than
     calling sendpage() in TCP (or maybe TLS).

 (4) Make tcp_bpf_sendpage() a wrapper around tcp_bpf_sendmsg().

 (5) Make AF_KCM use sendmsg() when calling down to TCP and then make it
     send entire fragment lists in single sendmsg calls.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=fd5f4d7da29218485153fd8b4c08da7fc130c79f [1]
====================

Link: https://lore.kernel.org/r/20230609100221.2620633-1-dhowells@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Rewrite the AF_KCM transmission loop to send all the fragments in a single
skb or frag_list-skb in one sendmsg() with MSG_SPLICE_PAGES set.  The list
of fragments in each skb is conveniently a bio_vec[] that can just be
attached to a BVEC iter.

Note: I'm working out the size of each fragment-skb by adding up bv_len for
all the bio_vecs in skb->frags[] - but surely this information is recorded
somewhere?  For the skbs in head->frag_list, this is equal to
skb->data_len, but not for the head.  head->data_len includes all the tail
frags too.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When transmitting data, call down into the transport socket using sendmsg
with MSG_SPLICE_PAGES to indicate that content should be spliced rather
than using sendpage.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make tcp_bpf_sendpage() a wrapper around tcp_bpf_sendmsg(MSG_SPLICE_PAGES)
rather than a loop calling tcp_sendpage().  sendpage() will be removed in
the future.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: John Fastabend <john.fastabend@gmail.com>
cc: Jakub Sitnicki <jakub@cloudflare.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When transmitting data, call down into TCP using sendmsg with
MSG_SPLICE_PAGES to indicate that content should be spliced rather than
performing sendpage calls to transmit header, data pages and trailer.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
cc: Trond Myklebust <trond.myklebust@hammerspace.com>
cc: Anna Schumaker <anna@kernel.org>
cc: Jeff Layton <jlayton@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove hash_sendpage*() as nothing should now call it since the rewrite of
splice_to_socket()[1].
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Link: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=2dc334f1a63a8839b88483a3e73c0f27c9c1791c [1]
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove file->f_op->sendpage as splicing to a socket now calls sendmsg
rather than sendpage.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>