- 01 Apr, 2024 16 commits
-
-
Alexander Lobakin authored
Historically, tunnel flags like TUNNEL_CSUM or TUNNEL_ERSPAN_OPT have been defined as __be16. Now all of those 16 bits are occupied and there's no more free space for new flags. It can't be simply switched to a bigger container with no adjustments to the values, since it's an explicit Endian storage, and on LE systems (__be16)0x0001 equals to (__be64)0x0001000000000000. We could probably define new 64-bit flags depending on the Endianness, i.e. (__be64)0x0001 on BE and (__be64)0x00010000... on LE, but that would introduce an Endianness dependency and spawn a ton of Sparse warnings. To mitigate them, all of those places which were adjusted with this change would be touched anyway, so why not define stuff properly if there's no choice. Define IP_TUNNEL_*_BIT counterparts as a bit number instead of the value already coded and a fistful of <16 <-> bitmap> converters and helpers. The two flags which have a different bit position are SIT_ISATAP_BIT and VTI_ISVTI_BIT, as they were defined not as __cpu_to_be16(), but as (__force __be16), i.e. had different positions on LE and BE. Now they both have strongly defined places. Change all __be16 fields which were used to store those flags, to IP_TUNNEL_DECLARE_FLAGS() -> DECLARE_BITMAP(__IP_TUNNEL_FLAG_NUM) -> unsigned long[1] for now, and replace all TUNNEL_* occurrences to their bitmap counterparts. Use the converters in the places which talk to the userspace, hardware (NFP) or other hosts (GRE header). The rest must explicitly use the new flags only. This must be done at once, otherwise there will be too many conversions throughout the code in the intermediate commits. Finally, disable the old __be16 flags for use in the kernel code (except for the two 'irregular' flags mentioned above), to prevent any accidental (mis)use of them. For the userspace, nothing is changed, only additions were made. Most noticeable bloat-o-meter difference (.text): vmlinux: 307/-1 (306) gre.ko: 62/0 (62) ip_gre.ko: 941/-217 (724) [*] ip_tunnel.ko: 390/-900 (-510) [**] ip_vti.ko: 138/0 (138) ip6_gre.ko: 534/-18 (516) [*] ip6_tunnel.ko: 118/-10 (108) [*] gre_flags_to_tnl_flags() grew, but still is inlined [**] ip_tunnel_find() got uninlined, hence such decrease The average code size increase in non-extreme case is 100-200 bytes per module, mostly due to sizeof(long) > sizeof(__be16), as %__IP_TUNNEL_FLAG_NUM is less than %BITS_PER_LONG and the compilers are able to expand the majority of bitmap_*() calls here into direct operations on scalars. Reviewed-by:
Simon Horman <horms@kernel.org> Signed-off-by:
Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Lobakin authored
Unlike IPv6 tunnels which use purely-kernel __ip6_tnl_parm structure to store params inside the kernel, IPv4 tunnel code uses the same ip_tunnel_parm which is being used to talk with the userspace. This makes it difficult to alter or add any fields or use a different format for whatever data. Define struct ip_tunnel_parm_kern, a 1:1 copy of ip_tunnel_parm for now, and use it throughout the code. Define the pieces, where the copy user <-> kernel happens, as standalone functions, and copy the data there field-by-field, so that the kernel-side structure could be easily modified later on and the users wouldn't have to care about this. Reviewed-by:
-
Alexander Lobakin authored
Commit dc34d503 ("lib: test_bitmap: add compile-time optimization/evaluations assertions") initially missed __assign_bit(), which led to that quite a time passed before I realized it doesn't get optimized at compilation time. Now that it does, add test for that just to make sure nothing will break one day. To make things more interesting, use bitmap_complement() and bitmap_full(), thus checking their compile-time evaluation as well. And remove the misleading comment mentioning the workaround removed recently in favor of adding the whole file to GCov exceptions. Reviewed-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by:
Yury Norov <yury.norov@gmail.com> Signed-off-by:
-
Alexander Lobakin authored
Now that we have generic bitmap_read() and bitmap_write(), which are inline and try to take care of non-bound-crossing and aligned cases to keep them optimized, collapse bitmap_{get,set}_value8() into simple wrappers around the former ones. bloat-o-meter shows no difference in vmlinux and -2 bytes for gpio-pca953x.ko, which says the optimization didn't suffer due to that change. The converted helpers have the value width embedded and always compile-time constant and that helps a lot. Suggested-by: -
Alexander Lobakin authored
The number of times yet another open coded `BITS_TO_LONGS(nbits) * sizeof(long)` can be spotted is huge. Some generic helper is long overdue. Add one, bitmap_size(), but with one detail. BITS_TO_LONGS() uses DIV_ROUND_UP(). The latter works well when both divident and divisor are compile-time constants or when the divisor is not a pow-of-2. When it is however, the compilers sometimes tend to generate suboptimal code (GCC 13): 48 83 c0 3f add $0x3f,%rax 48 c1 e8 06 shr $0x6,%rax 48 8d 14 c5 00 00 00 00 lea 0x0(,%rax,8),%rdx %BITS_PER_LONG is always a pow-2 (either 32 or 64), but GCC still does full division of `nbits + 63` by it and then multiplication by 8. Instead of BITS_TO_LONGS(), use ALIGN() and then divide by 8. GCC: 8d 50 3f lea 0x3f(%rax),%edx c1 ea 03 shr $0x3,%edx 81 e2 f8 ff ff 1f and $0x1ffffff8,%edx Now it shifts `nbits + 63` by 3 positions (IOW performs fast division by 8) and then masks bits[2:0]. bloat-o-meter: add/remove: 0/0 grow/shrink: 20/133 up/down: 156/-773 (-617) Clang does it better and generates the same code before/after starting from -O1, except that with the ALIGN() approach it uses %edx and thus still saves some bytes: add/remove: 0/0 grow/shrink: 9/133 up/down: 18/-538 (-520) Note that we can't expand DIV_ROUND_UP() by adding a check and using this approach there, as it's used in array declarations where expressions are not allowed. Add this helper to tools/ as well. Reviewed-by:
-
Alexander Lobakin authored
Currently, tools have *ALIGN*() macros scattered across the unrelated headers, as there are only 3 of them and they were added separately each time on an as-needed basis. Anyway, let's make it more consistent with the kernel headers and allow using those macros outside of the mentioned headers. Create <linux/align.h> inside the tools/ folder and include it where needed. Signed-off-by:
-
Alexander Lobakin authored
bitmap_set_bits() does not start with the FS' prefix and may collide with a new generic helper one day. It operates with the FS-specific types, so there's no change those two could do the same thing. Just add the prefix to exclude such possible conflict. Reviewed-by:
David Sterba <dsterba@suse.com> Reviewed-by:
-
Alexander Lobakin authored
bitmap_size() is a pretty generic name and one may want to use it for a generic bitmap API function. At the same time, its logic is NTFS-specific, as it aligns to the sizeof(u64), not the sizeof(long) (although it uses ideologically right ALIGN() instead of division). Add the prefix 'ntfs3_' used for that FS (not just 'ntfs_' to not mix it with the legacy module) and use generic BITS_TO_U64() while at it. Suggested-by: Yury Norov <yury.norov@gmail.com> # BITS_TO_U64() Reviewed-by:
-
Alexander Lobakin authored
bitmap_size() is a pretty generic name and one may want to use it for a generic bitmap API function. At the same time, its logic is not "generic", i.e. it's not just `nbits -> size of bitmap in bytes` converter as it would be expected from its name. Add the prefix 'idset_' used throughout the file where the function resides. Reviewed-by:
Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by:
-
Alexander Lobakin authored
Since commit b03fc117 ("bitops: let optimize out non-atomic bitops on compile-time constants"), the non-atomic bitops are macros which can be expanded by the compilers into compile-time expressions, which will result in better optimized object code. Unfortunately, turned out that passing `volatile` to those macros discards any possibility of optimization, as the compilers then don't even try to look whether the passed bitmap is known at compilation time. In addition to that, the mentioned linkmode helpers are marked with `inline`, not `__always_inline`, meaning that it's not guaranteed some compiler won't uninline them for no reason, which will also effectively prevent them from being optimized (it's a well-known thing the compilers sometimes uninline `2 + 2`). Convert linkmode_*_bit() from inlines to macros. Their calling convention are 1:1 with the corresponding bitops, so that it's not even needed to enumerate and map the arguments, only the names. No changes in vmlinux' object code (compiled by LLVM for x86_64) whatsoever, but that doesn't necessarily means the change is meaningless. Reviewed-by:
Jakub Kicinski <kuba@kernel.org> Acked-by:
-
Alexander Lobakin authored
Since commit b03fc117 ("bitops: let optimize out non-atomic bitops on compile-time constants"), the compilers are able to expand inline bitmap operations to compile-time initializers when possible. However, during the round of replacement if-__set-else-__clear with __assign_bit() as per Andy's advice, bloat-o-meter showed +1024 bytes difference in object code size for one module (even one function), where the pattern: DECLARE_BITMAP(foo) = { }; // on the stack, zeroed if (a) __set_bit(const_bit_num, foo); if (b) __set_bit(another_const_bit_num, foo); ... is heavily used, although there should be no difference: the bitmap is zeroed, so the second half of __assign_bit() should be compiled-out as a no-op. I either missed the fact that __assign_bit() has bitmap pointer marked as `volatile` (as we usually do for bitops) or was hoping that the compilers would at least try to look past the `volatile` for __always_inline functions. Anyhow, due to that attribute, the compilers were always compiling the whole expression and no mentioned compile-time optimizations were working. Convert __assign_bit() to a macro since it's a very simple if-else and all of the checks are performed inside __set_bit() and __clear_bit(), thus that wrapper has to be as transparent as possible. After that change, despite it showing only -20 bytes change for vmlinux (due to that it's still relatively unpopular), no drastic code size changes happen when replacing if-set-else-clear for onstack bitmaps with __assign_bit(), meaning the compiler now expands them to the actual operations will all the expected optimizations. Atomic assign_bit() is less affected due to its nature, but let's convert it to a macro as well to keep the code consistent and not leave a place for possible suboptimal codegen. Moreover, with certain kernel configuration it actually gives some saves (x86): do_ip_setsockopt 4154 4099 -55 Suggested-by: Yury Norov <yury.norov@gmail.com> # assign_bit(), too Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
-
Alexander Lobakin authored
Avoid open-coding that simple expression each time by moving BYTES_TO_BITS() from the probes code to <linux/bitops.h> to export it to the rest of the kernel. Simplify the macro while at it. `BITS_PER_LONG / sizeof(long)` always equals to %BITS_PER_BYTE, regardless of the target architecture. Do the same for the tools ecosystem as well (incl. its version of bitops.h). The previous implementation had its implicit type of long, while the new one is int, so adjust the format literal accordingly in the perf code. Suggested-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
-
Alexander Lobakin authored
Commit 8238b457 ("wait_on_bit: add an acquire memory barrier") added a new bitop, test_bit_acquire(), with proper wrapping in order to try to optimize it at compile-time, but missed the list of bitops used for checking their prototypes a bit below. The functions added have consistent prototypes, so that no more changes are required and no functional changes take place. Fixes: 8238b457 ("wait_on_bit: add an acquire memory barrier") Reviewed-by:
-
Alexander Potapenko authored
pr_err() messages may be treated as errors by some log readers, so let us only use them for test failures. For non-error messages, replace them with pr_info(). Suggested-by:
Alexander Potapenko <glider@google.com> Acked-by:
-
Alexander Potapenko authored
Add basic tests ensuring that values can be added at arbitrary positions of the bitmap, including those spanning into the adjacent unsigned longs. Two new performance tests, test_bitmap_read_perf() and test_bitmap_write_perf(), can be used to assess future performance improvements of bitmap_read() and bitmap_write(): [ 0.431119][ T1] test_bitmap: Time spent in test_bitmap_read_perf: 615253 [ 0.433197][ T1] test_bitmap: Time spent in test_bitmap_write_perf: 916313 (numbers from a Intel(R) Xeon(R) Gold 6154 CPU @ 3.00GHz machine running QEMU). Signed-off-by:
-
Syed Nayyar Waris authored
The two new functions allow reading/writing values of length up to BITS_PER_LONG bits at arbitrary position in the bitmap. The code was taken from "bitops: Introduce the for_each_set_clump macro" by Syed Nayyar Waris with a number of changes and simplifications: - instead of using roundup(), which adds an unnecessary dependency on <linux/math.h>, we calculate space as BITS_PER_LONG-offset; - indentation is reduced by not using else-clauses (suggested by checkpatch for bitmap_get_value()); - bitmap_get_value()/bitmap_set_value() are renamed to bitmap_read() and bitmap_write(); - some redundant computations are omitted. Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Syed Nayyar Waris <syednwaris@gmail.com> Signed-off-by:
William Breathitt Gray <william.gray@linaro.org> Link: https://lore.kernel.org/lkml/fe12eedf3666f4af5138de0e70b67a07c7f40338.1592224129.git.syednwaris@gmail.com/Suggested-by:
-
- 29 Mar, 2024 24 commits
-
-
Jakub Kicinski authored
Christophe Roullier says: ==================== Add property in dwmac-stm32 documentation Introduce property in dwmac-stm32 documentation - st,ext-phyclk: is present since 2020 in driver so need to explain it and avoid dtbs check issue : views/kernel/upstream/net-next/arch/arm/boot/dts/st/stm32mp157c-dk2.dtb: ethernet@5800a000: Unevaluated properties are not allowed ('st,ext-phyclk' was unexpected) Furthermore this property will be use in upstream of MP13 dwmac glue. (next step) ==================== Link: https://lore.kernel.org/r/20240328185337.332703-1-christophe.roullier@foss.st.comSigned-off-by: -
Christophe Roullier authored
The Linux kernel dwmac-stm32 driver currently supports three DT properties used to configure whether PHY clock are generated by the MAC or supplied to the MAC from the PHY. Originally there were two properties, st,eth-clk-sel and st,eth-ref-clk-sel, each used to configure MAC clocking in different bus mode and for different MAC clock frequency. Since it is possible to determine the MAC 'eth-ck' clock frequency from the clock subsystem and PHY bus mode from the 'phy-mode' property, two disparate DT properties are no longer required to configure MAC clocking. Linux kernel commit 1bb694e2 ("net: ethernet: stmmac: simplify phy modes management for stm32") introduced a third, unified, property st,ext-phyclk. This property covers both use cases of st,eth-clk-sel and st,eth-ref-clk-sel DT properties, as well as a new use case for 25 MHz clock generated by the MAC. The third property st,ext-phyclk is so far undocumented, document it. Below table summarizes the clock requirement and clock sources for supported PHY interface modes. __________________________________________________________________________ |PHY_MODE | Normal | PHY wo crystal| PHY wo crystal |No 125Mhz from PHY| | | | 25MHz | 50MHz | | --------------------------------------------------------------------------- | MII | - | eth-ck | n/a | n/a | | | | st,ext-phyclk | | | --------------------------------------------------------------------------- | GMII | - | eth-ck | n/a | n/a | | | | st,ext-phyclk | | | --------------------------------------------------------------------------- | RGMII | - | eth-ck | n/a | eth-ck | | | | st,ext-phyclk | | st,eth-clk-sel or| | | | | | st,ext-phyclk | --------------------------------------------------------------------------- | RMII | - | eth-ck | eth-ck | n/a | | | | st,ext-phyclk | st,eth-ref-clk-sel | | | | | | or st,ext-phyclk | | --------------------------------------------------------------------------- Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Christophe Roullier <christophe.roullier@foss.st.com> Link: https://lore.kernel.org/r/20240328185337.332703-2-christophe.roullier@foss.st.comSigned-off-by:
-
Johannes Berg authored
There are, especially with multi-attr arrays, many cases of needing to iterate all attributes of a specific type in a netlink message or a nested attribute. Add specific macros to support that case. Also convert many instances using this spatch: @@ iterator nla_for_each_attr; iterator name nla_for_each_attr_type; identifier nla; expression head, len, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_attr(nla, head, len, rem) +nla_for_each_attr_type(nla, ATTR, head, len, rem) { <... T x; ...> -if (nla_type(nla) == ATTR) { ... -} } @@ identifier nla; iterator nla_for_each_nested; iterator name nla_for_each_nested_type; expression attr, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_nested(nla, attr, rem) +nla_for_each_nested_type(nla, ATTR, attr, rem) { <... T x; ...> -if (nla_type(nla) == ATTR) { ... -} } @@ iterator nla_for_each_attr; iterator name nla_for_each_attr_type; identifier nla; expression head, len, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_attr(nla, head, len, rem) +nla_for_each_attr_type(nla, ATTR, head, len, rem) { <... T x; ...> -if (nla_type(nla) != ATTR) continue; ... } @@ identifier nla; iterator nla_for_each_nested; iterator name nla_for_each_nested_type; expression attr, rem; expression ATTR; type T; identifier x; @@ -nla_for_each_nested(nla, attr, rem) +nla_for_each_nested_type(nla, ATTR, attr, rem) { <... T x; ...> -if (nla_type(nla) != ATTR) continue; ... } Although I had to undo one bad change this made, and I also adjusted some other code for whitespace and to use direct variable initialization now. Signed-off-by:Johannes Berg <johannes.berg@intel.com> Link: https://lore.kernel.org/r/20240328203144.b5a6c895fb80.I1869b44767379f204998ff44dd239803f39c23e0@changeidSigned-off-by:
-
Jakub Kicinski authored
Eric Dumazet says: ==================== udp: small changes on receive path This series is based on an observation I made in UDP receive path. The sock_def_readable() costs are pretty high, especially when epoll is used to generate EPOLLIN events. First patch annotates races on sk->sk_rcvbuf reads. Second patch replaces an atomic_add_return() with a less expensive atomic_add() Third patch avoids calling sock_def_readable() when possible. Fourth patch adds sk_wake_async_rcu() to get better inlining and code generation. ==================== Link: https://lore.kernel.org/r/20240328144032.1864988-1-edumazet@google.comSigned-off-by:
-
Eric Dumazet authored
While looking at UDP receive performance, I saw sk_wake_async() was no longer inlined. This matters at least on AMD Zen1-4 platforms (see SRSO) This might be because rcu_read_lock() and rcu_read_unlock() are no longer nops in recent kernels ? Add sk_wake_async_rcu() variant, which must be called from contexts already holding rcu lock. As SOCK_FASYNC is deprecated in modern days, use unlikely() to give a hint to the compiler. sk_wake_async_rcu() is properly inlined from __udp_enqueue_schedule_skb() and sock_def_readable(). Signed-off-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240328144032.1864988-5-edumazet@google.comSigned-off-by:
-
Eric Dumazet authored
sock_def_readable() is quite expensive (particularly when ep_poll_callback() is in the picture). We must call sk->sk_data_ready() when : - receive queue was empty, or - SO_PEEK_OFF is enabled on the socket, or - sk->sk_data_ready is not sock_def_readable. We still need to call sk_wake_async(). Signed-off-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240328144032.1864988-4-edumazet@google.comSigned-off-by:
-
Eric Dumazet authored
atomic_add_return() is more expensive than atomic_add() and seems overkill in UDP rx fast path. Signed-off-by:
-
Eric Dumazet authored
sk->sk_rcvbuf is read locklessly twice, while other threads could change its value. Use a READ_ONCE() to annotate the race. Signed-off-by:
-
Jakub Kicinski authored
Arnd Bergmann says: ==================== address remaining -Wtautological-constant-out-of-range-compare The warning option was introduced a few years ago but left disabled by default. All of the actual bugs that this has found have been fixed in the meantime, and this series should address the remaining false-positives, as tested on arm/arm64/x86 randconfigs as well as allmodconfig builds for all architectures supported by clang. ==================== Link: https://lore.kernel.org/r/20240328143051.1069575-1-arnd@kernel.orgSigned-off-by:
-
Arnd Bergmann authored
When building with 64KB pages, clang points out that xsk->chunk_size can never be PAGE_SIZE: drivers/net/ethernet/mellanox/mlx5/core/en/xsk/setup.c:19:22: error: result of comparison of constant 65536 with expression of type 'u16' (aka 'unsigned short') is always false [-Werror,-Wtautological-constant-out-of-range-compare] if (xsk->chunk_size > PAGE_SIZE || ~~~~~~~~~~~~~~~ ^ ~~~~~~~~~ In older versions of this code, using PAGE_SIZE was the only possibility, so this would have never worked on 64KB page kernels, but the patch apparently did not address this case completely. As Maxim Mikityanskiy suggested, 64KB chunks are really not all that useful, so just shut up the warning by adding a cast. Fixes: 282c0c79 ("net/mlx5e: Allow XSK frames smaller than a page") Link: https://lore.kernel.org/netdev/20211013150232.2942146-1-arnd@kernel.org/ Link: https://lore.kernel.org/lkml/a7b27541-0ebb-4f2d-bd06-270a4d404613@app.fastmail.com/Signed-off-by:Arnd Bergmann <arnd@arndb.de> Acked-by:
Maxim Mikityanskiy <maxtram95@gmail.com> Reviewed-by:
Justin Stitt <justinstitt@google.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20240328143051.1069575-9-arnd@kernel.orgSigned-off-by:
-
Suraj Gupta authored
Add description of mdio enable, mdio disable and mdio wait functions. Add description of skb pointer in axidma_bd data structure. Remove 'phy_node' description in axienet local data structure since it is not a valid struct member. Correct description of struct axienet_option. Fix below kernel-doc warnings in drivers/net/ethernet/xilinx/: 1) xilinx_axienet_mdio.c:1: warning: no structured comments found 2) xilinx_axienet.h:379: warning: Function parameter or struct member 'skb' not described in 'axidma_bd' 3) xilinx_axienet.h:538: warning: Excess struct member 'phy_node' description in 'axienet_local' 4) xilinx_axienet.h:1002: warning: expecting prototype for struct axiethernet_option. Prototype was for struct axienet_option instead Signed-off-by:
Suraj Gupta <suraj.gupta2@amd.com> Reviewed-by:
Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Link: https://lore.kernel.org/r/20240328110713.12885-1-suraj.gupta2@amd.comSigned-off-by:
-
Su Hui authored
Clang static checker(scan-buid): drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c:503:2: warning: Value stored to 'rsp_hdr' is never read [deadcode.DeadStores] Remove these unused variables to save some space. Signed-off-by:
Su Hui <suhui@nfschina.com> Reviewed-by:
-
Krzysztof Kozlowski authored
Core in spi_register_driver() already sets the .owner, so driver does not need to. Signed-off-by:
-
Krzysztof Kozlowski authored
Core in spi_register_driver() already sets the .owner, so driver does not need to. Signed-off-by:
-
Krzysztof Kozlowski authored
Core in mhi_driver_register() already sets the .owner, so driver does not need to. Signed-off-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Link: https://lore.kernel.org/r/20240327174810.519676-2-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Krzysztof Kozlowski authored
Core in spi_register_driver() already sets the .owner, so driver does not need to. Signed-off-by:
-
Donald Hunter authored
The NLMSGERR_ATTR_POLICY extack attribute has been ignored by ynl up to now. Extend extack decoding to include _POLICY and the nested NL_POLICY_TYPE_ATTR_* attributes. For example: ./tools/net/ynl/cli.py \ --spec Documentation/netlink/specs/rt_link.yaml \ --create --do newlink --json '{ "ifname": "12345678901234567890", "linkinfo": {"kind": "bridge"} }' Netlink error: Numerical result out of range nl_len = 104 (88) nl_flags = 0x300 nl_type = 2 error: -34 extack: {'msg': 'Attribute failed policy validation', 'policy': {'max-length': 15, 'type': 'string'}, 'bad-attr': '.ifname'} Signed-off-by:Donald Hunter <donald.hunter@gmail.com> Link: https://lore.kernel.org/r/20240328155636.64688-1-donald.hunter@gmail.comSigned-off-by:
-
Jian Wen authored
During live migration of a virtual machine, the SR-IOV VF need to be re-registered. It may fail when the memory is badly fragmented. The related log is as follows. kernel: hv_netvsc 6045bdaa-c0d1-6045-bdaa-c0d16045bdaa eth0: VF slot 1 added ... kernel: kworker/0:0: page allocation failure: order:7, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0 kernel: CPU: 0 PID: 24006 Comm: kworker/0:0 Tainted: G E 5.4...x86_64 #1 kernel: Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090008 12/07/2018 kernel: Workqueue: events work_for_cpu_fn kernel: Call Trace: kernel: dump_stack+0x8b/0xc8 kernel: warn_alloc+0xff/0x170 kernel: __alloc_pages_slowpath+0x92c/0xb2b kernel: ? get_page_from_freelist+0x1d4/0x1140 kernel: __alloc_pages_nodemask+0x2f9/0x320 kernel: alloc_pages_current+0x6a/0xb0 kernel: kmalloc_order+0x1e/0x70 kernel: kmalloc_order_trace+0x26/0xb0 kernel: ? __switch_to_asm+0x34/0x70 kernel: __kmalloc+0x276/0x280 kernel: ? _raw_spin_unlock_irqrestore+0x1e/0x40 kernel: devlink_alloc+0x29/0x110 kernel: mlx5_devlink_alloc+0x1a/0x20 [mlx5_core] kernel: init_one+0x1d/0x650 [mlx5_core] kernel: local_pci_probe+0x46/0x90 kernel: work_for_cpu_fn+0x1a/0x30 kernel: process_one_work+0x16d/0x390 kernel: worker_thread+0x1d3/0x3f0 kernel: kthread+0x105/0x140 kernel: ? max_active_store+0x80/0x80 kernel: ? kthread_bind+0x20/0x20 kernel: ret_from_fork+0x3a/0x50 Signed-off-by:Jian Wen <wenjian1@xiaomi.com> Link: https://lore.kernel.org/r/20240327082128.942818-1-wenjian1@xiaomi.comSigned-off-by:
-
Jakub Kicinski authored
Arnd Bergmann says: ==================== enabled -Wformat-truncation for clang With randconfig build testing, I found only eight files that produce warnings with clang when -Wformat-truncation is enabled. This means we can just turn it on by default rather than only enabling it for "make W=1". Unfortunately, gcc produces a lot more warnings when the option is enabled, so it's not yet possible to turn it on both compilers. ==================== Link: https://lore.kernel.org/r/20240326223825.4084412-1-arnd@kernel.orgSigned-off-by:
-
Arnd Bergmann authored
clang warns that one error message is too long for its destination buffer: drivers/net/ethernet/mellanox/mlx5/core/esw/bridge.c:1876:4: error: 'snprintf' will always be truncated; specified size is 80, but format string expands to at least 94 [-Werror,-Wformat-truncation-non-kprintf] Reword it to be a bit shorter so it always fits. Fixes: 70f0302b ("net/mlx5: Bridge, implement mdb offload") Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Link: https://lore.kernel.org/r/20240326223825.4084412-5-arnd@kernel.orgSigned-off-by:
-
Arnd Bergmann authored
clang complains that the temporary string for the name passed into alloc_workqueue() is too short for its contents: drivers/net/ethernet/qlogic/qed/qed_main.c:1218:3: error: 'snprintf' will always be truncated; specified size is 16, but format string expands to at least 18 [-Werror,-Wformat-truncation] There is no need for a temporary buffer, and the actual name of a workqueue is 32 bytes (WQ_NAME_LEN), so just use the interface as intended to avoid the truncation. Fixes: 59ccf86f ("qed: Add driver infrastucture for handling mfw requests.") Signed-off-by:
-
Arnd Bergmann authored
As clang points out, the error message in enetc_setup_xdp_prog() still does not fit in the buffer and will be truncated: drivers/net/ethernet/freescale/enetc/enetc.c:2771:3: error: 'snprintf' will always be truncated; specified size is 80, but format string expands to at least 87 [-Werror,-Wformat-truncation] Replace it with an even shorter message that should fit. Fixes: f968c564 ("net: enetc: shorten enetc_setup_xdp_prog() error message to fit NETLINK_MAX_FMTMSG_LEN") Signed-off-by:
-
Radha Mohan Chintakuntla authored
Any NIX interface type can have maximum 256 channels. So increased the backpressure ID count to 256 so that it can cover cn9k and cn10k SoCs that have different NIX interface types with varied maximum channels. Signed-off-by:
Radha Mohan Chintakuntla <radhac@marvell.com> Link: https://lore.kernel.org/r/20240326184514.1628284-1-radhac@marvell.comSigned-off-by:
-
Jakub Kicinski authored
Balazs Scheidler says: ==================== Add IP/port information to UDP drop tracepoint In our use-case we would like to recover the properties of dropped UDP packets. Unfortunately the current udp_fail_queue_rcv_skb tracepoint only exposes the port number of the receiving socket. This patch-set will add the source/dest ip/port to the tracepoint, while keeping the socket's local port as well for compatibility. Thanks for the review comments by Jason and Kuniyuki, they helped me a lot and I tried to address all of their comments in this new iteration. ==================== Link: https://lore.kernel.org/r/cover.1711475011.git.balazs.scheidler@axoflow.comSigned-off-by:
-
