Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field.  This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.

This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.

Tested on custom i.MX28 board with SSP0 SPI driver.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)

The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.

It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.

Cc: stable@kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mx31pdk target fails to build:

  CC      init/version.o
  LD      init/built-in.o
  LD      .tmp_vmlinux1
arch/arm/mach-imx/built-in.o: In function `mx31_3ds_init':
mach-mx31_3ds.c:(.init.text+0x548): undefined reference to `imx_add_mxc_mmc'
mach-mx31_3ds.c:(.init.text+0x69c): undefined reference to `imx31_mxc_mmc_data'
make: *** [.tmp_vmlinux1] Error

Fix this by passsing IMX_HAVE_PLATFORM_MXC_MMC option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

While suspending, we're enabling a clock in ->suspend() but we're in atomic
context, leading to this :

[30803.667305] PM: late suspend of devices complete after 1.237 msecs
[30803.667449] BUG: sleeping function called from invalid context at kernel/mutex.c:271
[30803.667464] in_atomic(): 0, irqs_disabled(): 128, pid: 4941, name: pm-suspend
[30803.667474] INFO: lockdep is turned off.
[30803.667483] irq event stamp: 0
[30803.667489] hardirqs last  enabled at (0): [<  (null)>]   (null)
[30803.667503] hardirqs last disabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667543] softirqs last  enabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667562] softirqs last disabled at (0): [<  (null)>]   (null)
[30803.667574] Backtrace:
[30803.667611] [<c0010e00>] (dump_backtrace+0x0/0x110) from [<c0424c00>] (dump_stack+0x18/0x1c)
[30803.667624]  r6:00000000 r5:00000000 r4:d9648000 r3:d9648000
[30803.667652] [<c0424be8>] (dump_stack+0x0/0x1c) from [<c0424eec>] (__might_sleep.part.101+0x90/0xa8)
[30803.667673] [<c0424e5c>] (__might_sleep.part.101+0x0/0xa8) from [<c001a5c4>] (__might_sleep+0x80/0x94)
[30803.667686]  r4:c05d58c0
[30803.667705] [<c001a544>] (__might_sleep+0x0/0x94) from [<c043230c>] (mutex_lock_nested+0x2c/0x30c)
[30803.667735] [<c04322e0>] (mutex_lock_nested+0x0/0x30c) from [<c0017834>] (clk_enable+0x28/0x50)
[30803.667747]  r8:c0438464 r7:00000003 r6:00000000 r5:00000000 r4:c05d2e98
[30803.667780] [<c001780c>] (clk_enable+0x0/0x50) from [<c0017260>] (mx5_suspend_enter+0x1c/0x98)
[30803.667792]  r4:00000003 r3:c060dfe0
[30803.667821] [<c0017244>] (mx5_suspend_enter+0x0/0x98) from [<c0059b48>] (suspend_enter+0xec/0x15c)
[30803.667833]  r4:00000003 r3:c0017244
[30803.667856] [<c0059a5c>] (suspend_enter+0x0/0x15c) from [<c0059c4c>] (suspend_devices_and_enter+0x94/0x130)
[30803.667868]  r6:00000000 r5:00000003 r4:c0c0af00 r3:00002710
[30803.667897] [<c0059bb8>] (suspend_devices_and_enter+0x0/0x130) from [<c0059db0>] (enter_state+0xc8/0x130)
[30803.667909]  r6:00000000 r5:00000003 r4:c05286e4
[30803.667934] [<c0059ce8>] (enter_state+0x0/0x130) from [<c00592d4>] (state_store+0xac/0xc0)
[30803.667945]  r6:00000003 r5:00000003 r4:df39d000 r3:00000003
[30803.667978] [<c0059228>] (state_store+0x0/0xc0) from [<c01b0100>] (kobj_attr_store+0x1c/0x28)
[30803.668009] [<c01b00e4>] (kobj_attr_store+0x0/0x28) from [<c00e435c>] (sysfs_write_file+0x88/0xbc)
[30803.668032] [<c00e42d4>] (sysfs_write_file+0x0/0xbc) from [<c0091fa0>] (vfs_write+0xbc/0x138)
[30803.668051] [<c0091ee4>] (vfs_write+0x0/0x138) from [<c0092204>] (sys_write+0x44/0x70)
[30803.668062]  r8:00000000 r7:00000004 r6:00000003 r5:002694d0 r4:d966acc0
[30803.668094] [<c00921c0>] (sys_write+0x0/0x70) from [<c000db00>] (ret_fast_syscall+0x0/0x3c)
[30803.668106]  r9:d9648000 r8:c000dcc4 r6:00000001 r5:002694d0 r4:00000003
[30803.669927] PM: early resume of devices complete after 0.972 msecs

Just move the clk_enable/disable in ->prepare() and ->finish()
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Add group event scheduling option to perf record/stat
  MAINTAINERS: Fix list of perf events source files
  perf tools: Fix build against newer glibc
  perf tools: Fix error handling of unknown events
  perf evlist: Fix missing event name init for default event
  perf list: Fix exit value

* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/tracing: Fix tracing config option properly
  xen: Do not enable PV IPIs when vector callback not present
  xen/x86: replace order-based range checking of M2P table by linear one
  xen: xen-selfballoon.c needs more header files

Steven Rostedt says we should use CONFIG_EVENT_TRACING.

Cc:Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Fix regression for HVM case on older (<4.1.1) hypervisors caused by

  commit 99bbb3a8
  Author: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
  Date:   Thu Dec 2 17:55:10 2010 +0000

    xen: PV on HVM: support PV spinlocks and IPIs

This change replaced the SMP operations with event based handlers without
taking into account that this only works when the hypervisor supports
callback vectors. This causes unexplainable hangs early on boot for
HVM guests with more than one CPU.

BugLink: http://bugs.launchpad.net/bugs/791850

CC: stable@kernel.org
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-and-Reported-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: core: handle ack_busy when fetching the Config ROM

This fixes a regression introduced by commit cdcb725c ("Btrfs: check
if there is enough space for balancing smarter").  We can't do 64-bit
divides on 32-bit architectures.

In cases where we need to divide/multiply by 2 we should just left/right
shift respectively, and in cases where theres N number of devices use
do_div.  Also make the counters u64 to match up with rw_devices.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Acked-and-tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: flush any pending end_io requests before DIO reads w/dioread_nolock
  ext4: fix nomblk_io_submit option so it correctly converts uninit blocks
  ext4: Resolve the hang of direct i/o read in handling EXT4_IO_END_UNWRITTEN.
  ext4: call ext4_ioend_wait and ext4_flush_completed_IO in ext4_evict_inode
  ext4: Fix ext4_should_writeback_data() for no-journal mode

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: sound/aoa/fabrics/layout.c: remove unneeded kfree
  ALSA: hda - Fix error check from snd_hda_get_conn_index() in patch_cirrus.c
  ALSA: hda - Don't spew too many ELD errors
  ALSA: usb-audio - Fix missing mixer dB information
  ALSA: hda - Add "PCM" volume to vmaster slave list
  ALSA: hda - Fix duplicated capture-volume creation for ALC268 models
  ALSA: ac97: Add HP Compaq dc5100 SFF(PT003AW) to Headphone Jack Sense whitelist
  ALSA: snd_usb_caiaq: track submitted output urbs

Fix new kernel-doc warning in pci.c:

  Warning(drivers/pci/pci.c:3259): No description found for parameter 'mps'
  Warning(drivers/pci/pci.c:3259): Excess function parameter 'rq' description in 'pcie_set_mps'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The label outnodev is only used when kzalloc has not yet taken place or has
failed, so there is no need for the call for kfree under this label.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@

(
if (...) { ... when != kfree(x)
               when != x = E3
               when != E3 = x
*  return ...;
 }
... when != x = E2
    when != I(...,x,...) S
if (...) { ... when != x = E4
 kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

snd_hda_get_conn_index() returns a negative value while the current code
stores it in an unsigned int.  It must be stored in a signed integer.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Currently HD-audio driver shows the all error ELD byte as an error
in the kernel message.  This is annoying when the video driver doesn't
set the correct ELD from the beginning. e.g. radeon sends a zero-byte
data, but we still check ELD with the fixed 128 byte as a workaround
for some broken devices, it spews 128-times errors.

For avoiding this, the driver aborts reading when the first byte is
invalid.  In such a case, the whole data is certainly invalid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
  drm/i915: set GFX_MODE to pre-Ivybridge default value even on Ivybridge

There is a race between ext4 buffer write and direct_IO read with
dioread_nolock mount option enabled. The problem is that we clear
PageWriteback flag during end_io time but will do
uninitialized-to-initialized extent conversion later with dioread_nolock.
If an O_direct read request comes in during this period, ext4 will return
zero instead of the recently written data.

This patch checks whether there are any pending uninitialized-to-initialized
extent conversion requests before doing O_direct read to close the race.
Note that this is just a bandaid fix. The fundamental issue is that we
clear PageWriteback flag before we really complete an IO, which is
problem-prone. To fix the fundamental issue, we may need to implement an
extent tree cache that we can use to look up pending to-be-converted extents.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org

Prior to Ivybridge, the GFX_MODE would default to 0x800, meaning that
MI_FLUSH would flush the TLBs in addition to the rest of the caches
indicated in the MI_FLUSH command.  However starting with Ivybridge, the
register defaults to 0x2800 out of reset, meaning that to invalidate the
TLB we need to use PIPE_CONTROL.  Since we're not doing that yet, go
back to the old default so things work.

v2: don't forget to actually *clear* the new bit
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

* 'for-linus' of git://git.kernel.dk/linux-block: (23 commits)
  Revert "cfq: Remove special treatment for metadata rqs."
  block: fix flush machinery for stacking drivers with differring flush flags
  block: improve rq_affinity placement
  blktrace: add FLUSH/FUA support
  Move some REQ flags to the common bio/request area
  allow blk_flush_policy to return REQ_FSEQ_DATA independent of *FLUSH
  xen/blkback: Make description more obvious.
  cfq-iosched: Add documentation about idling
  block: Make rq_affinity = 1 work as expected
  block: swim3: fix unterminated of_device_id table
  block/genhd.c: remove useless cast in diskstats_show()
  drivers/cdrom/cdrom.c: relax check on dvd manufacturer value
  drivers/block/drbd/drbd_nl.c: use bitmap_parse instead of __bitmap_parse
  bsg-lib: add module.h include
  cfq-iosched: Reduce linked group count upon group destruction
  blk-throttle: correctly determine sync bio
  loop: fix deadlock when sysfs and LOOP_CLR_FD race against each other
  loop: add BLK_DEV_LOOP_MIN_COUNT=%i to allow distros 0 pre-allocated loop devices
  loop: add management interface for on-demand device allocation
  loop: replace linked list of allocated devices with an idr index
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: OF: Don't crash when bridge parent is NULL.
  PCI: export pcie_bus_configure_settings symbol
  PCI: code and comments cleanup
  PCI: make cardbus-bridge resources optional
  PCI: make SRIOV resources optional
  PCI : ability to relocate assigned pci-resources
  PCI: honor child buses add_size in hot plug configuration
  PCI: Set PCI-E Max Payload Size on fabric

In pcibios_get_phb_of_node(), we will crash while booting if
bus->bridge->parent is NULL.

Check for this case and avoid dereferencing the NULL pointer.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

We have a kernel build regression since 3.1-rc1, which is about 10%
regression. The kernel source is in an ext3 filesystem.
Alex Shi bisect it to commit:
commit a07405b7
Author: Justin TerAvest <teravest@google.com>
Date:   Sun Jul 10 22:09:19 2011 +0200

    cfq: Remove special treatment for metadata rqs.

Apparently this is caused by lack metadata preemption, where ext3/ext4
do use READ_META. I didn't see a way to fix the issue, so suggest
reverting the patch.

This reverts commit a07405b7.

Reported-by: Alex Shi<alex.shi@intel.com>
Reported-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

The recent fix for testing dB range at the mixer creation time seems
to cause regressions in some devices.  In such devices, reading the dB
info at probing time gives an error, thus both dBmin and dBmax are still
zero, and TLV flag isn't set although the later read of dB info succeeds.

This patch adds a workaround for such a case by assuming that the later
read will succeed.  In future, a similar test should be performed in a
case where a wrong dB range is seen even in the later read.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: fix array bounds error setting up PCIC NMI trap

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  drivers/ata/sata_dwc_460ex.c: add missing kfree
  ata: Add iMX pata support
  pata_via: disable ATAPI DMA on AVERATEC 3200
  [libata] sata_sil: fix used-uninit warning

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4.1: Return NFS4ERR_BADSESSION to callbacks during session resets
  NFSv4.1: Fix the callback 'highest_used_slotid' behaviour
  pnfs-obj: Fix the comp_index != 0 case
  pnfs-obj: Bug when we are running out of bio
  nfs: add missing prefetch.h include

  CC      arch/sparc/kernel/pcic.o
arch/sparc/kernel/pcic.c: In function 'pcic_probe':
arch/sparc/kernel/pcic.c:359:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:359:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:8: error: array subscript is above array bounds [-Werror=array-bounds]
cc1: all warnings being treated as errors

I'm not particularly familiar with sparc but t_nmi (defined in head_32.S via
the TRAP_ENTRY macro) and pcic_nmi_trap_patch (defined in entry.S) both appear
to be 4 instructions long and I presume from the usage that instructions are
int sized.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, error handling code in this function calls the function
sata_dwc_port_stop, but this function has essentially no effect if hsdevp
has not been stored in ap, which is the case throughout this function.  The
only effect is to print a debugging message including ap->print_id.

The code is rewritten to not call sata_dwc_port_stop, but instead to jump
to a local label that prints the original error message and the print_id
information.  In the case where hsdevp has been already allocated (but not
yet stored in ap), this value is freed as well.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Add basic support for pata on iMX. It has been tested only on imx51.
SDMA support will probably be added later so this version supports only
PIO.

v2:
  - enable only when needed IORDY
  - use dev_get_drvdata
v3:
  - add missing clk_put() calls
  - use platform_get_irq()
  - fix resume code to avoid disabling IORDY on resume
v4:
  - Remove EXPERIMENTAL and switch to depends on ARCH_MXC
  - Use devm_kzalloc()
  - make clock a must-have
  - Use only 1 ioremap
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

On AVERATEC 3200, pata_via causes memory corruption with ATAPI DMA,
which often leads to random kernel oops.  The cause of the problem is
not well understood yet and only small subset of machines using the
controller seem affected.  Blacklist ATAPI DMA on the machine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11426Reported-and-tested-by: Jim Bray <jimsantelmo@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Init 'serror' to silence the following warning:

drivers/ata/sata_sil.c: In function ‘sil_interrupt’:
drivers/ata/sata_sil.c:453:14: warning: ‘serror’ may be used uninitialized in
this function [-Wuninitialized]

This is not a 'can never happen' but is nonetheless extremely unlikely.
The easiest and cleanest warning fix is simply to init the var,
rather than worry about marking the var uninit-ok.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: set i_size properly when fallocating and we already
  btrfs: unlock on error in btrfs_file_llseek()
  btrfs: btrfs_permission's RO check shouldn't apply to device nodes
  Btrfs: truncate pages from clone ioctl target range
  Btrfs: fix uninitialized sync_pending
  Btrfs: fix wrong free space information
  btrfs: memory leak in btrfs_add_inode_defrag()
  Btrfs: use plain page_address() in header fields setget functions
  Btrfs: forced readonly when btrfs_drop_snapshot() fails
  Btrfs: check if there is enough space for balancing smarter
  Btrfs: fix a bug of balance on full multi-disk partitions
  Btrfs: fix an oops of log replay
  Btrfs: detect wether a device supports discard
  Btrfs: force unplugs when switching from high to regular priority bios

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  update cifs version to 1.75
  [CIFS] possible memory corruption on mount
  cifs: demote cERROR in build_path_from_dentry to cFYI

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/iser: Support iSCSI PDU padding
  IBiser: Fix wrong mask when sizeof (dma_addr_t) > sizeof (unsigned long)
  IPoIB: Fix possible NULL dereference in ipoib_start_xmit()

* git://git.kernel.org/pub/scm/linux/kernel/git/hirofumi/fatfs-2.6:
  fat: fat16 support maximum 4GB file/vol size as WinXP or 7.
  fat: fix utf8 iocharset warning message
  fat: fix build warning

Fix kernel-doc warning in irqdesc.c:

  Warning(kernel/irq/irqdesc.c:353): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Based on a patch from the PaX Team, found during a clang analysis pass.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: stable@kernel.org [v2.6.35+]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent