- 27 Apr, 2012 11 commits
-
-
Christian Riesch authored
commit 5b76d060 upstream. Under heavy load (flood ping) it is possible for the MDIO timeout to expire before the loop checks the GO bit again. This patch adds an additional check whether the operation was done before actually returning -ETIMEDOUT. To reproduce this bug, flood ping the device, e.g., ping -f -l 1000 After some time, a "timed out waiting for user access" warning may appear. And even worse, link may go down since the PHY reported a timeout. Signed-off-by:
Christian Riesch <christian.riesch@omicron.at> Cc: Cyril Chemparathy <cyril@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Oliver Neukum authored
commit 5bd7b419 upstream. Fatal errors such as a device disconnect must not trigger error handling. The error returns must be checked. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Oliver Neukum authored
commit 9426cd05 upstream. del_timer_sync() cannot be used in interrupt. Replace it with del_timer() and a flag Signed-off-by:
-
Tomoki Sekiyama authored
commit 532f17b5 upstream. Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb structure, and this causes BUG_ON with some USB host implementations. This patch fixes the issue. Signed-off-by:
Tomoki Sekiyama <tomoki.sekiyama@gmail.com> Signed-off-by:
-
Tomoki Sekiyama authored
commit 523fc5c1 upstream. Removes allocation of coherent buffer for the control-request setup-packet buffer from the yurex driver. Using coherent buffers for setup-packet is obsolete and does not work with some USB host implementations. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 3066616c upstream. A rather annoying and common case is when booting a PVonHVM guest and exposing the PV KBD and PV VFB - as broken toolstacks don't always initialize the backends correctly. Normally The HVM guest is using the VGA driver and the emulated keyboard for this (though upstream version of QEMU implements PV KBD, but still uses a VGA driver). We provide a very basic two-stage wait mechanism - where we wait for 30 seconds for all devices, and then for 270 for all them except the two mentioned. That allows us to wait for the essential devices, like network or disk for the full 6 minutes. To trigger this, put this in your guest config: vfb = [ 'vnc=1, vnclisten=0.0.0.0 ,vncunused=1'] instead of this: vnc=1 vnclisten="0.0.0.0" Acked-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> [v3: Split delay in non-essential (30 seconds) and essential devices per Ian and Stefano suggestion] [v4: Added comments per Stefano suggestion] Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Stefano Stabellini authored
commit e8e937be upstream. Since we are using the m2p_override we do have struct pages corresponding to the user vma mmap'ed by gntdev. Removing the VM_PFNMAP flag makes get_user_pages work on that vma. An example test case would be using a Xen userspace block backend (QDISK) on a file on NFS using O_DIRECT. Signed-off-by:
-
Alexander Shiyan authored
commit 7a6fbc9a upstream. Since 2.6.30-rc1 clps711x serial driver hungs system. This is a result of call disable_irq from ISR. synchronize_irq waits for end of interrupt and goes to infinite loop. This patch fix this problem. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Takashi Iwai authored
commit ca3649de upstream. Some output pins on Conexant chips have no HP control bit, but the auto-parser initializes these pins unconditionally with PIN_HP. Check the pin-capability and avoid the HP bit if not supported. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kent Yoder authored
commit 25c3d30c upstream. The current code only increments the upper 64 bits of the SHA-512 byte counter when the number of bytes hashed happens to hit 2^64 exactly. This patch increments the upper 64 bits whenever the lower 64 bits overflows. Signed-off-by:
Kent Yoder <key@linux.vnet.ibm.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Zeev Tarantov authored
[Patch not needed upstream as this is a backport build bugfix - gregkh gcc correctly complains: util/hist.c: In function ‘__hists__add_entry’: util/hist.c:240:27: error: invalid type argument of ‘->’ (have ‘struct hist_entry’) util/hist.c:241:23: error: invalid type argument of ‘->’ (have ‘struct hist_entry’) for this new code: + if (he->ms.map != entry->ms.map) { + he->ms.map = entry->ms.map; + if (he->ms.map) + he->ms.map->referenced = true; + } because "entry" is a "struct hist_entry", not a pointer to a struct. In mainline, "entry" is a pointer to struct passed as argument to the function. So this is broken during backporting. But obviously not compile tested. Signed-off-by:Zeev Tarantov <zeev.tarantov@gmail.com> Cc: Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
- 22 Apr, 2012 29 commits
-
-
Greg Kroah-Hartman authored
-
Martin Schwidefsky authored
commit cd94154c upstream. Git commit 36409f63 "use generic RCU page-table freeing code" introduced a tlb flushing bug. Partially revert the above git commit and go back to s390 specific page table flush code. For s390 the TLB can contain three types of entries, "normal" TLB page-table entries, TLB combined region-and-segment-table (CRST) entries and real-space entries. Linux does not use real-space entries which leaves normal TLB entries and CRST entries. The CRST entries are intermediate steps in the page-table translation called translation paths. For example a 4K page access in a three-level page table setup will create two CRST TLB entries and one page-table TLB entry. The advantage of that approach is that a page access next to the previous one can reuse the CRST entries and needs just a single read from memory to create the page-table TLB entry. The disadvantage is that the TLB flushing rules are more complicated, before any page-table may be freed the TLB needs to be flushed. In short: the generic RCU page-table freeing code is incorrect for the CRST entries, in particular the check for mm_users < 2 is troublesome. This is applicable to 3.0+ kernels. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Dave Airlie authored
commit a09d431f upstream. When the force changes went in back in 3.3.0, we ended up returning disconnected in the !force case, and the connected in when forced, as it hit the hardcoded check. Fix it so all exits go via the hardcoded check and stop spurious modesets on platforms with hardcoded EDIDs. Reported-by: Evan McNabb (Red Hat) Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Dave Airlie authored
commit 16a5e32b upstream. My rv515 card is very flaky with msi enabled. Every so often it loses a rearm and never comes back, manually banging the rearm brings it back. Reviewed-by:
-
Takashi Iwai authored
commit e3632507 upstream. The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms: fix analog load detection on DVI-I connectors] is obviously wrong, and it's the culprit of the regression on my workstation with DVI-analog connection resulting in the blank output. Fixed the typo now. Signed-off-by:
-
Kees Cook authored
commit bdbb776f upstream. It was possible to extract the robust list head address from a setuid process if it had used set_robust_list(), allowing an ASLR info leak. This changes the permission checks to be the same as those used for similar info that comes out of /proc. Running a setuid program that uses robust futexes would have had: cred->euid != pcred->euid cred->euid == pcred->uid so the old permissions check would allow it. I'm not aware of any setuid programs that use robust futexes, so this is just a preventative measure. (This patch is based on changes from grsecurity.) Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: David Howells <dhowells@redhat.com> Cc: Serge E. Hallyn <serge.hallyn@canonical.com> Cc: kernel-hardening@lists.openwall.com Cc: spender@grsecurity.net Link: http://lkml.kernel.org/r/20120319231253.GA20893@www.outflux.netSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Cho, Yu-Chen authored
commit 07c0ea87 upstream. Add Atheros maryann 0cf3:311d PIDVID support This module is AR3012 Series. Include /sys/kernel/debug/usb/devices output here for reference before: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.01 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms after: T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0cf3 ProdID=311d Rev= 0.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Cho, Yu-Chen <acho@suse.com> cked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
-
Eran authored
commit 9498ba7a upstream. The bluetooth module in the Asus UX31/UX21 is based on Atheros AR3012 and requires a firmware to be uploaded before it's usable. output of usb-devices for this module: T: Bus=01 Lev=02 Prnt=02 Port=07 Cnt=03 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3375 Rev=00.02 S: Manufacturer=Atheros Communications S: Product=Bluetooth USB Host Controller S: SerialNumber=Alaska Day 2006 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
Eran <eran@over-here.org> Tested-by:
Michal Labedzki <michal.labedzki@tieto.com> Signed-off-by:
Gustavo F. Padovan <padovan@profusion.mobi> Cc: Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
-
NeilBrown authored
commit afbaa90b upstream. If a bitmap is added while the array is active, it is possible for bitmap_daemon_work to run while the bitmap is being initialised. This is particularly a problem if bitmap_daemon_work sees bitmap->filemap as non-NULL before it has been filled in properly. So hold bitmap_info.mutex while filling in ->filemap to prevent problems. This patch is suitable for any -stable kernel, though it might not apply cleanly before about 3.1. Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Tomoya MORINAGA authored
commit ca7fe2db upstream. ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by:
Tomoya MORINAGA <tomoya.rohm@gmail.com> Signed-off-by:
Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit c43f1508 upstream. Currently, executing suspend/hibernation, memory access violation occurs. In pch_dma_save_regs() called by suspend(), you can see the following code. static void pch_dma_save_regs(struct pch_dma *pd) { snip... list_for_each_entry_safe(chan, _c, &pd->dma.channels, device_node) { pd_chan = to_pd_chan(chan); pd->ch_regs[i].dev_addr = channel_readl(pd_chan, DEV_ADDR); pd->ch_regs[i].mem_addr = channel_readl(pd_chan, MEM_ADDR); pd->ch_regs[i].size = channel_readl(pd_chan, SIZE); pd->ch_regs[i].next = channel_readl(pd_chan, NEXT); i++; } } Max loop count is 12 defined at pci_table. So, this caused memory access violation. This patch fixes the issue - Modify array size (MAX_CHAN_NR) Signed-off-by:
Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 0b052f4a upstream. Currently, Mode-Control register is accessed by read-modify-write. According to DMA hardware specifications datasheet, prohibits this method. Because this register resets to 0 by DMA HW after DMA transfer completes. Thus, current read-modify-write processing can cause unexpected behavior. The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'. e.g. Set DMA0=01b DMA11=10b CTL0=33333331h CTL2=00002333h NOTE: CTL0 includes DMA0~7 Mode-Control register. CTL2 includes DMA8~11 Mode-Control register. This patch modifies the issue. Signed-off-by:
Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Alexander Stein authored
commit 70f18915 upstream. Fix for the following INFO message ================================= [ INFO: inconsistent lock state ] 2.6.39+ #89 --------------------------------- inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage. rs232/822 [HC1[1]:SC0[0]:HE0:SE1] takes: (&(&pd_chan->lock)->rlock){?.....}, at: [<c123b9a1>] pdc_desc_get+0x16/0xab {HARDIRQ-ON-W} state was registered at: [<c104fe28>] mark_irqflags+0xbd/0x11a [<c1050386>] __lock_acquire+0x501/0x6bb [<c1050945>] lock_acquire+0x63/0x7b [<c131c51d>] _raw_spin_lock_bh+0x43/0x51 [<c123bee4>] pd_alloc_chan_resources+0x92/0x11e [<c123ad62>] dma_chan_get+0x9b/0x107 [<c123b2d1>] __dma_request_channel+0x61/0xdc [<c11ba24b>] pch_request_dma+0x61/0x19e [<c11bb3b8>] pch_uart_startup+0x16a/0x1a2 [<c11b8446>] uart_startup+0x87/0x147 [<c11b9183>] uart_open+0x117/0x13e [<c11a5c7d>] tty_open+0x23c/0x34c [<c1097705>] chrdev_open+0x140/0x15f [<c10930a6>] __dentry_open.clone.14+0x14a/0x22b [<c1093dfb>] nameidata_to_filp+0x36/0x40 [<c109f28b>] do_last+0x513/0x635 [<c109f4af>] path_openat+0x9c/0x2aa [<c109f6e4>] do_filp_open+0x27/0x69 [<c1093f02>] do_sys_open+0xfd/0x184 [<c1093fad>] sys_open+0x24/0x2a [<c131d58c>] sysenter_do_call+0x12/0x32 irq event stamp: 2522 hardirqs last enabled at (2521): [<c131ca3b>] _raw_spin_unlock_irqrestore+0x36/0x52 hardirqs last disabled at (2522): [<c131db27>] common_interrupt+0x27/0x34 softirqs last enabled at (2354): [<c102fa11>] __do_softirq+0x10a/0x11a softirqs last disabled at (2299): [<c10041a4>] do_softirq+0x57/0xa4 other info that might help us debug this: 2 locks held by rs232/822: #0: (&tty->atomic_write_lock){+.+.+.}, at: [<c11a4b7a>] tty_write_lock+0x14/0x3c #1: (&port_lock_key){-.....}, at: [<c11bad72>] pch_uart_interrupt+0x17/0x1e9 stack backtrace: Pid: 822, comm: rs232 Not tainted 2.6.39+ #89 Call Trace: [<c1319f90>] ? printk+0x19/0x1b [<c104f893>] print_usage_bug+0x184/0x18f [<c104e5b1>] ? print_irq_inversion_bug+0x10e/0x10e [<c104f943>] mark_lock_irq+0xa5/0x1f6 [<c104fc9c>] mark_lock+0x208/0x2d7 [<c104fdc0>] mark_irqflags+0x55/0x11a [<c1050386>] __lock_acquire+0x501/0x6bb [<c10042ee>] ? dump_trace+0x92/0xb6 [<c1050945>] lock_acquire+0x63/0x7b [<c123b9a1>] ? pdc_desc_get+0x16/0xab [<c131c2d0>] _raw_spin_lock+0x3e/0x4c [<c123b9a1>] ? pdc_desc_get+0x16/0xab [<c123b9a1>] pdc_desc_get+0x16/0xab [<c10504d8>] ? __lock_acquire+0x653/0x6bb [<c123bb2c>] pd_prep_slave_sg+0x7c/0x1cb [<c1006c3f>] ? nommu_map_sg+0x6e/0x81 [<c11bace6>] dma_handle_tx+0x2cf/0x344 [<c11bad72>] ? pch_uart_interrupt+0x17/0x1e9 [<c11baebb>] pch_uart_interrupt+0x160/0x1e9 [<c10642fb>] handle_irq_event_percpu+0x25/0x127 [<c1064429>] handle_irq_event+0x2c/0x43 [<c1065e0d>] ? handle_fasteoi_irq+0x84/0x84 [<c1065eb9>] handle_edge_irq+0xac/0xce <IRQ> [<c1003ecb>] ? do_IRQ+0x38/0x9d [<c131db2e>] ? common_interrupt+0x2e/0x34 [<c105007b>] ? __lock_acquire+0x1f6/0x6bb [<c131ca3d>] ? _raw_spin_unlock_irqrestore+0x38/0x52 [<c11b798b>] ? uart_start+0x2d/0x32 [<c11b7998>] ? uart_flush_chars+0x8/0xa [<c11a7962>] ? n_tty_write+0x12c/0x1c6 [<c1027a73>] ? try_to_wake_up+0x251/0x251 [<c11a4d0b>] ? tty_write+0x169/0x1dc [<c11a7836>] ? n_tty_ioctl+0xb7/0xb7 [<c1094841>] ? vfs_write+0x91/0x10d [<c11a4ba2>] ? tty_write_lock+0x3c/0x3c [<c1094a69>] ? sys_write+0x3e/0x63 [<c131d58c>] ? sysenter_do_call+0x12/0x32 Signed-off-by:
Alexander Stein <alexander.stein@systec-electronic.com> Tested-by:
-
Tomoya MORINAGA authored
commit c3d4913c upstream. ISSUE: In case PCH_DMA with I2S communications with ch8~ch11, sometimes I2S data is not send correctly. CAUSE: The following patch I submitted before was not enough modification for supporting DMA ch8~ch11. The modification for status register of ch8~11 was not enough. pch_dma: Support I2S for ML7213 IOH author Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Mon, 9 May 2011 07:09:38 +0000 (16:09 +0900) committer Vinod Koul <vinod.koul@intel.com> Mon, 9 May 2011 11:42:23 +0000 (16:42 +0530) commit 194f5f27 tree c9d4903ea02b18939a4f390956a48be1a3734517 parent 60092d0b This patch fixes the issue. We can confirm PCH_DMA with I2S communications with ch8~ch11 works well. Signed-off-by:
-
Tomoya MORINAGA authored
commit 64d91cfa upstream. Currently, ".setup" function is not set. As a result, when detecting our IOH's uart device without pch_uart, kernel panic occurs at the following of pciserial_init_ports(). for (i = 0; i < nr_ports; i++) { if (quirk->setup(priv, board, &serial_port, i)) break; So, this patch adds the ".setup" function. We can use pci_default_setup because our IOH's uart is compatible with 16550. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 6c4b47d2 upstream. Currently, PCIe bus number is set as fixed value "2". However, PCIe bus number is not always "2". This patch sets bus number using probe() parameter. Signed-off-by:
-
Jonghwan Choi authored
commit 51b79bee upstream. Add missing "personality.h" security/commoncap.c: In function 'cap_bprm_set_creds': security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function) security/commoncap.c:510: error: (Each undeclared identifier is reported only once security/commoncap.c:510: error: for each function it appears in.) Signed-off-by:
Jonghwan Choi <jhbird.choi@samsung.com> Acked-by:
Serge Hallyn <serge.hallyn@canonical.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Cc: Eric Paris <eparis@redhat.com> Signed-off-by:
-
Lin Ming authored
commit 8931d9ea upstream. Allow referenced objects to be in a different scope. http://www.acpica.org/bugzilla/show_bug.cgi?id=937 http://marc.info/?l=linux-acpi&m=131636632718222&w=2 ACPI Error: [RAMB] Namespace lookup failure, AE_NOT_FOUND (20110112/psargs-359) ACPI Exception: AE_NOT_FOUND, Could not execute arguments for [RAMW] (Region) (20110112/nsinit-349) Scope (_SB) { Name (RAMB, 0xDF5A1018) OperationRegion (\RAMW, SystemMemory, RAMB, 0x00010000) } For above ASL code, we need to save scope node(\_SB) to lookup the argument node(\_SB.RAMB). Reported-by:
Jim Green <student.northwestern@gmail.com> Signed-off-by:
Lin Ming <ming.m.lin@intel.com> Signed-off-by:
Bob Moore <robert.moore@intel.com> Signed-off-by:
Len Brown <len.brown@intel.com> Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 731ad81e upstream. ML7831 is companion chip for Intel Atom E6xx series. Signed-off-by:
-
Tomoya MORINAGA authored
commit 83331040 upstream. ISSUE: USB Suspend interrupts occur frequently. CAUSE: When it is called pch_udc_reconnect() in USB Suspend, it repeats reset and Suspend. SOLUTION: pch_udc_reconnect() does not enable all interrupts. When an enumeration event occurred the driver enables all interrupts. Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Tomoya MORINAGA authored
commit 1c575d2d upstream. ISSUE: After a USB cable is connect/disconnected, the system rarely freezes. CAUSE: Since the USB device controller cannot know to disconnect the USB cable, when it is used without detecting VBUS by GPIO, the UDC driver does not notify to USB Gadget. Since USB Gadget cannot know to disconnect, a false setting occurred when the USB cable is connected/disconnect repeatedly. Signed-off-by:
-
Tomoya MORINAGA authored
commit 84566abb upstream. ISSUE: After USB Suspend, a system rarely freezes. CAUSE: When USB Suspend occurred, the driver is not notifying a gadget of the event. Signed-off-by:
-
Tomoya MORINAGA authored
commit c802672c upstream. ISSUE: If the return value of pch_udc_pcd_init() is False, the return value of this function is unsettled. Since pch_udc_pcd_init() always returns 0, there is not actually the issue. CAUSE: If pch_udc_pcd_init() is True, the variable, retval, is not set for an appropriate value. Signed-off-by:
-
Tomoya MORINAGA authored
commit c50a3bff upstream. ISSUE: When the driver notifies a gadget of a disconnect event, a system rarely freezes. CAUSE: When the driver calls dev->driver->disconnect(), it is not calling spin_unlock(). Signed-off-by:
-
Tomoya MORINAGA authored
commit 9914a0de upstream. Currently, external ROM access is enabled/disabled in probe()/remove(). So, when a buggy software access unanticipated memory area, in case of enabling this ADE bit, external ROM memory area can be broken. This patch enables the ADE bit only accessing external ROM area. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Tomoya MORINAGA authored
commit dd7d7fea upstream. Only ML7213/ML7223(Bus-n) has this register. Currently,this driver doesn't care register "FUNCSEL" in suspend/resume. This patch saves/restores FUNCSEL register only when the device is ML7213 or ML7223(Bus-n). Signed-off-by:
-
Tomoya MORINAGA authored
commit 20ae6d0b upstream. Register "interrupt delay value" is for GbE which is connected to Bus-m of PCIe. However currently, the value is set for Bus-n. As a result, the value is not set correctly. This patch moves setting the value processing of Bus-n to Bus-m. Signed-off-by:
-
Johan Hovold authored
commit 94324962 upstream. Make sure hci_dev_open returns immediately if hci_dev_unregister has been called. This fixes a race between hci_dev_open and hci_dev_unregister which can lead to a NULL-pointer dereference. Bug is 100% reproducible using hciattach and a disconnected serial port: 0. # hciattach -n /dev/ttyO1 any noflow 1. hci_dev_open called from hci_power_on grabs req lock 2. hci_init_req executes but device fails to initialise (times out eventually) 3. hci_dev_open is called from hci_sock_ioctl and sleeps on req lock 4. hci_uart_tty_close calls hci_dev_unregister and sleeps on req lock in hci_dev_do_close 5. hci_dev_open (1) releases req lock 6. hci_dev_do_close grabs req lock and returns as device is not up 7. hci_dev_unregister sleeps in destroy_workqueue 8. hci_dev_open (3) grabs req lock, calls hci_init_req and eventually sleeps 9. hci_dev_unregister finishes, while hci_dev_open is still running... [ 79.627136] INFO: trying to register non-static key. [ 79.632354] the code is fine but needs lockdep annotation. [ 79.638122] turning off the locking correctness validator. [ 79.643920] [<c00188bc>] (unwind_backtrace+0x0/0xf8) from [<c00729c4>] (__lock_acquire+0x1590/0x1ab0) [ 79.653594] [<c00729c4>] (__lock_acquire+0x1590/0x1ab0) from [<c00733f8>] (lock_acquire+0x9c/0x128) [ 79.663085] [<c00733f8>] (lock_acquire+0x9c/0x128) from [<c0040a88>] (run_timer_softirq+0x150/0x3ac) [ 79.672668] [<c0040a88>] (run_timer_softirq+0x150/0x3ac) from [<c003a3b8>] (__do_softirq+0xd4/0x22c) [ 79.682281] [<c003a3b8>] (__do_softirq+0xd4/0x22c) from [<c003a924>] (irq_exit+0x8c/0x94) [ 79.690856] [<c003a924>] (irq_exit+0x8c/0x94) from [<c0013a50>] (handle_IRQ+0x34/0x84) [ 79.699157] [<c0013a50>] (handle_IRQ+0x34/0x84) from [<c0008530>] (omap3_intc_handle_irq+0x48/0x4c) [ 79.708648] [<c0008530>] (omap3_intc_handle_irq+0x48/0x4c) from [<c037499c>] (__irq_usr+0x3c/0x60) [ 79.718048] Exception stack(0xcf281fb0 to 0xcf281ff8) [ 79.723358] 1fa0: 0001e6a0 be8dab00 0001e698 00036698 [ 79.731933] 1fc0: 0002df98 0002df38 0000001f 00000000 b6f234d0 00000000 00000004 00000000 [ 79.740509] 1fe0: 0001e6f8 be8d6aa0 be8dac50 0000aab8 80000010 ffffffff [ 79.747497] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 79.756011] pgd = cf3b4000 [ 79.758850] [00000000] *pgd=8f0c7831, *pte=00000000, *ppte=00000000 [ 79.765502] Internal error: Oops: 80000007 [#1] [ 79.770294] Modules linked in: [ 79.773529] CPU: 0 Tainted: G W (3.3.0-rc6-00002-gb5d5c879 #421) [ 79.781066] PC is at 0x0 [ 79.783721] LR is at run_timer_softirq+0x16c/0x3ac [ 79.788787] pc : [<00000000>] lr : [<c0040aa4>] psr: 60000113 [ 79.788787] sp : cf281ee0 ip : 00000000 fp : cf280000 [ 79.800903] r10: 00000004 r9 : 00000100 r8 : b6f234d0 [ 79.806427] r7 : c0519c28 r6 : cf093488 r5 : c0561a00 r4 : 00000000 [ 79.813323] r3 : 00000000 r2 : c054eee0 r1 : 00000001 r0 : 00000000 [ 79.820190] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 79.827728] Control: 10c5387d Table: 8f3b4019 DAC: 00000015 [ 79.833801] Process gpsd (pid: 1265, stack limit = 0xcf2802e8) [ 79.839965] Stack: (0xcf281ee0 to 0xcf282000) [ 79.844573] 1ee0: 00000002 00000000 c0040a24 00000000 00000002 cf281f08 00200200 00000000 [ 79.853210] 1f00: 00000000 cf281f18 cf281f08 00000000 00000000 00000000 cf281f18 cf281f18 [ 79.861816] 1f20: 00000000 00000001 c056184c 00000000 00000001 b6f234d0 c0561848 00000004 [ 79.870452] 1f40: cf280000 c003a3b8 c051e79c 00000001 00000000 00000100 3fa9e7b8 0000000a [ 79.879089] 1f60: 00000025 cf280000 00000025 00000000 00000000 b6f234d0 00000000 00000004 [ 79.887756] 1f80: 00000000 c003a924 c053ad38 c0013a50 fa200000 cf281fb0 ffffffff c0008530 [ 79.896362] 1fa0: 0001e6a0 0000aab8 80000010 c037499c 0001e6a0 be8dab00 0001e698 00036698 [ 79.904998] 1fc0: 0002df98 0002df38 0000001f 00000000 b6f234d0 00000000 00000004 00000000 [ 79.913665] 1fe0: 0001e6f8 be8d6aa0 be8dac50 0000aab8 80000010 ffffffff 00fbf700 04ffff00 [ 79.922302] [<c0040aa4>] (run_timer_softirq+0x16c/0x3ac) from [<c003a3b8>] (__do_softirq+0xd4/0x22c) [ 79.931945] [<c003a3b8>] (__do_softirq+0xd4/0x22c) from [<c003a924>] (irq_exit+0x8c/0x94) [ 79.940582] [<c003a924>] (irq_exit+0x8c/0x94) from [<c0013a50>] (handle_IRQ+0x34/0x84) [ 79.948913] [<c0013a50>] (handle_IRQ+0x34/0x84) from [<c0008530>] (omap3_intc_handle_irq+0x48/0x4c) [ 79.958404] [<c0008530>] (omap3_intc_handle_irq+0x48/0x4c) from [<c037499c>] (__irq_usr+0x3c/0x60) [ 79.967773] Exception stack(0xcf281fb0 to 0xcf281ff8) [ 79.973083] 1fa0: 0001e6a0 be8dab00 0001e698 00036698 [ 79.981658] 1fc0: 0002df98 0002df38 0000001f 00000000 b6f234d0 00000000 00000004 00000000 [ 79.990234] 1fe0: 0001e6f8 be8d6aa0 be8dac50 0000aab8 80000010 ffffffff [ 79.997161] Code: bad PC value [ 80.000396] ---[ end trace 6f6739840475f9ee ]--- [ 80.005279] Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by:
Johan Hovold <jhovold@gmail.com> Acked-by:
-
Sarah Sharp authored
commit c7713e73 upstream. The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering that the xHCI registers are saved and restored in. It moves the interrupt pending (IMAN) and interrupt control (IMOD) registers to be saved and restored last. I believe that's because the host controller may attempt to fetch the event ring table when interrupts are re-enabled. Therefore we need to restore the event ring registers before we re-enable interrupts. This should be backported to kernels as old as 2.6.37, that contain the commit 5535b1d5 "USB: xHCI: PCI power management implementation" Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by:
Elric Fu <elricfu1@gmail.com> Cc: Andiry Xu <andiry.xu@amd.com> Signed-off-by:
-
