While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’

dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:

[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
 #ifdef CONFIG_MAC80211_DEBUGFS
       struct dentry *rs_sta_dbgfs_scale_table_file;
       struct dentry *rs_sta_dbgfs_stats_table_file;
       struct dentry *rs_sta_dbgfs_rate_scale_data_file;
       struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
       u32 dbg_fixed_rate;
 #endif

The issue was introduced by commit a1da077b:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use "__packed" instead of "__attribute__ ((packed))"...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 00d3f14c has removed the references of this macro,
but left it only. So remove this definition.

commit 00d3f14c
Author: Johannes Berg <johannes@sipsolutions.net>
Date:   Tue Feb 10 21:26:00 2009 +0100

    mac80211: use cfg80211s BSS infrastructure

    Remove all the code from mac80211 to keep track of BSSes
    and use the cfg80211-provided code completely.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is not required for USB devices.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.

The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

patch "iwlagn: check ready in iwlagn_bss_info_changed()" introduce
whitespace, fix it

please merge with the previous patch

Reported by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
	The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65

Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-1000.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-agn-eeprom.c
	drivers/net/wireless/iwlwifi/iwl-core.h

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-1000.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-core.h

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Change some file names and Kconfig settings so that this new module matches
the new way of using wl12xx instead of wl1271.

Also fix SDIO power enabling and disabling to match the latest way of doing
it.

Cc: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

With the current single-queue implementation traffic priorization is not
working correctly - when using multiple BE streams and one, say VI stream,
the VI stream will share bandwidth almost equally with the BE streams.

To fix the issue, implement per AC queues, which are emptied in priority
order to the firmware. To keep it relatively simple, maintain a global
buffer count and global queue stop/wake instead of per-AC.

With these changes, priorization appears to work just fine.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

Currently, the debug level is set in compilation time (by the DEBUG_LEVEL
const). This method has the advantage of compiling only the relevant
messages, while optimizing out the unused ones.

In order to allow runtime control over the debug_level, while optimizing
out messages when debug messages are not needed, we combine some methods:
1. use dynamic_debug (pr_debug) rather then printk.
2. add debug_level module param in order to set debug level during insmod.
3. add debug_level sysfs file in order to allow dynamic control over the
   debug level.

Since patches for pr_debug_hex_dump() implementation haven't been applied yet,
we are still temporarly using print_hex_dump().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

Inclusion of a WPS IE in probe requests caused a problem
in the driver due to the maximum size of the probe request
template and the max_scan_ie_len values at initialization.

Increased the size of probe request template
to the maximum size allowed by the firmware.
Struct wl12xx_probe_req_template, which was only used
for calculating the max size of the probe request template,
is no longer used and needed.

max_scan_ie_len is used for validating the size of
additional IEs in scan requests.
Initialized the max_scan_ie_len field to the maximum size
of the probe request template minus the ieee80211 header size.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.

in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

This module enables individually generating RX and TX traffic
over the SDIO bus on which the WL1271 chipset is connected.
This is required to perform RF interference testing.

The module takes 2 module parameters 'rx' and 'tx'.

To generate RX traffic:
	modprobe wl1271_sdio_test rx=1
To generate TX traffic:
	modprobe wl1271_sdio_test tx=1

To generate both RX & TX traffic, set both rx and tx to 1.

You can change the testing configuration at runtime by changing
the rx & tx values at /sys/modules/wl1271_sdio_test/

To stop testing simply unload the module.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Reviewed-by: Carlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early.  At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.

To fix this, we disable 11a channels when we read the NVS instead.  Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>

This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Multiple devices use almost the same .cfg with minor differences.
Use macro and remove the duplication. By doing this, reduce
the chance for mistake while modify .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For debugging purpose, keep track of the bt coex enable/disable state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For WiFi/WiMAX combo devices, if WiMAX own the RF, WiFi driver
try to access RF and fail. This is the W/A to To avoid WiFi keep
reloading firmware and try to access RF again.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For enhanced tx power table in EEPROM, add more detail logging
to help debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For logging EEPROM related info, instead of using IWL_DEBUG_INFO,
use the dedicated logging (IWL_DEBUG_EEPROM) for easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Adding new debug type to log EEPROM related data
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This removes the old TX power reading code, it isn't
necessary since the new code is able to read all the
various EEPROM layouts due to relying on information
contained in the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.

However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For the new 1x1 devices, hw and uCode will support rx
antenna diversity, but we need to indicate 1x1 device to
AccessPoint to make sure it won't use MIMO.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

The compiler correctly warns:
iwl-agn-tx.c: In function ‘iwlagn_tx_status_reply_compressed_ba’:
iwl-agn-tx.c:1240: warning: ‘bitmap’ may be used uninitialized in this function

Move the debug print to the branch that reads the
bitmap, and move the variables too so it's more
obvious where they are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

In function iwlagn_bss_info_changed(), we need to check if the driver
is ready before doing real work. Also, the previously put WARN() is
removed because the vif is not guaranteed to be valid. uCode restart
routine will clear the vif.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

This prevent bad fixed_rate keeps crashing uCode in an endless loop.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

For both 6005 and 6030 devices, change the led compensation to 57
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Commit 6175ddf0 changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".

Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.

This renames the queues using this mapping:
	QID_AC_BK -> QID_AC_VO (priority 0)
	QID_AC_BE -> QID_AC_VI (priority 1)
	QID_AC_VI -> QID_AC_BE (priority 2)
	QID_AC_VO -> QID_AC_BK (priority 3)

Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>